Sony MEX-BT5100 Service Manual page 10

MEX-BT5100
1
1
1 8 2
m m
5 3 m
m
A
TOYOTA
max. size
5 8 mm
( 7 / 11 / in)
32 32
Dimensions
max. 5 8 mm
( 7 / 11 / po)
32 32
Tamaño máx.
5 8 mm
Bracket
Support
Soporte
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
Piezas existentes suministradas con su automóvil
A
Precautions
• Choose the installation location carefully so that the
unit will not interfere with normal driving operations.
• Avoid installing the unit in areas subject to dust, dirt,
excessive vibration, or high temperatures, such as in
direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a safe
and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket
Before installing the unit, remove the protection
collar and the bracket from the unit.
1
Remove the protection collar .
Pinch both edges of the protection collar , then
pull it out.
2
Remove the bracket .
Insert both release keys together between
the unit and the bracket until they click.
Pull down the bracket , then pull up the unit
to separate.
10
2
Face the hook inwards.
Tournez le crochet vers
l'intérieur.
El gancho debe
encontrarse en la parte
interior.
2
Claws
Griffes
Uñas
B
NISSAN
max. size
5 8 mm
( 7 / 11 / in)
32 32
Dimensions
to dashboard/center console max. 5 8 mm
vers le tableau de bord/la console centrale
( 7 / 11 / po)
32 32
al tablero o consola central
Tamaño máx.
5 8 mm
max. size
5 8 mm
( 7 / 11 / in)
32 32
Dimensions
max. 5 8 mm
( 7 / 11 / po)
32 32
Tamaño máx.
5 8 mm
Bracket
Support
Soporte
B
Mounting example
Installation in the dashboard
Notes
• Bend these claws outward for a tight fi t, if necessary (
• Make sure that the 4 catches on the protection collar
properly engaged in the slots of the unit ( -3).
Mounting the unit in a Japanese
car
You may not be able to install this unit in some makes of
Japanese cars. In such a case, consult your Sony dealer.
Note
To prevent malfunction, install only with the supplied screws
3
Dashboard
Tableau de bord
Tablero
to dashboard/center console
vers le tableau de bord/la console centrale
al tablero o consola central
Bracket
Support
Soporte
Bracket
Support
Soporte
Existing parts supplied with your car
Pièces existantes fournies avec la voiture
Piezas existentes suministradas con su automóvil
How to detach and attach the
front panel
Before installing the unit, detach the front panel.
-2).
are
-A To detach
Before detaching the front panel, be sure to press
Press , then slide the front panel to the right, and
gently pull out the left end of the front panel.
-B To attach
Place the hole of the front panel onto the spindle
on the unit, then lightly push the left side in.
.
max. size
5 8 mm
( 7 / 11 / in)
32 32
Dimensions
max. 5 8 mm
( 7 / 11 / po)
32 32
Tamaño máx.
5 8 mm
Warning if your car's ignition
has no ACC position
After turning the ignition off, be sure to press
and hold on the unit until the display
disappears.
Otherwise, the display does not turn off and this causes
. battery drain.
RESET button
When the installation and connections are completed,
be sure to press the RESET button with a ball-point pen,
etc., after detaching the front panel.