Sewing Data; Sewing Data List - JUKI LBH-1700 Series Engineer's Manual

1
READY
4
5
PATTERN
3
6
WIDTH
PITCH

(2) Sewing data list

No. Setting item
1 Cloth cut length
2 Knife groove width, right
3 Knife groove width, left
＊3
4 Stitch width, left
5 2nd bar-tacking length
6 1st clearance
7 2nd clearance
8 Pitch at pararell section
9 Pitch at bar-tacking section
＊5
10 Shape
11 Length of radial round type shape
12 Number of stitches of radial shape
2
RESET CLAMP WINDER THREAD
DATA COUNTER TENSION
KNIFE
LEFT/BARTACK/RIGHT
CLEARANCE
LENGTH
LEFT/CLEARANCE/RIGHT
– +
FEED
This item sets length of cloth that is cut by cloth cutting knife.
When knife performs plural motions, plural motions are performed in accordance
with knife size which has been set, and the cloth is cut as much as the set value.
Normally, knife length is set for the knife drop of one time.
(Setting more than 3 types of presser size is treated as the special order.)
This item sets the clearance between cloth cutting knife and right parallel section.
This item sets the clearance between cloth cutting knife and left parallel section.
This item sets stitch width of left parallel section.
This item sets length of 2nd bar-tacking section.
Square type, radial square type, radial taper bar, radial straight bar, eyelet square
type, eyelet flow bar-tacking, eyelet straight bar-tacking : 2nd bar-tacking setting
This item sets the clearance between 1st bar-tacking and knife groove.
This item sets the clearance between 2nd bar-tacking and knife groove.
Sewing machine performs jump feed after stopping and knife operates depending on
the set value.
This item sets sewing pitch of left and right parallel sections.
This item sets sewing pitch of bar-tacking section.
This item selects the shape.
0 : Square 1 : Radial 2 : Radial square
type type type
9 : Eyelet 10 : Eyelet
square type radial type
This item sets length of bar-tacking section.
Radial square type, round square type, radial taper bar, radial straight bar :
1st bar-tacking setting
Radial, round type, semilunar type : Common setting to 1st abd 2nd bar-tacking.
Eyelet radial type : 2nd bar-tacking setting
This item sets number of stitches of radial shape section.
1

(1) Sewing data

1) Make sure that sewing LED 1 goes off.
(When it lights up, press [Ready]
the LED go off.)
2) Press [Pattern No.]
7
No. (It is not necessary when the pattern is not
changed.)
3) Press [Left
8
pattern No. you desire to change. (It is not necessary
when the pattern is not changed.)
4) Press [Data]
5) Press [Left
data No. you desire to change.
6) Press [Right
the data.
7) Repeat steps 5), and 6) and when setting is completed,
press [Ready]
(When turning OFF the power without pressing
[Ready]
Then, it is necessary to re-enter.)
Description
5 : Radial
4 : Round 6 : Radial
taper
square straight
3 : Round
bar
type bar
type
11 : Eyelet flow bar- 12 : Eyelet straight bar-
tacking type tacking type
2 3
54
− −
key 3 to display the pattern
] key 4 or [Left ] key 5 to select the
key 6 to display the data No.
] key 4 or [Left ] key 5 to select the
] key 7 or [Right
key 2 to light up sewing LED.
key 2, the data is not stored in memory.
Setting range
6.0 to 67.0
0 to 2.0
0 to 2.0
0.1 to 3.0
0.2 to 5.0
0 to 4.0
0 to 4.0
0.20 to 2.5
0.20 to 2.5
0/1/2/3/4/5/6/7/8/9/
7 : Bar-tacking 8 : Semilunar
10/11/12
type
1.0 to 5.0
1 to 4
4
key 2 to make
] key 8 to change
Unit
0.1 mm
0.05 mm
0.05 mm
0.05 mm
0.1 mm
0.1 mm
0.1 mm
0.05 mm
0.05 mm
1
0.1 mm
1N