Download Print this page
ETC ColorSource PAR Installation Manual

ETC ColorSource PAR Installation Manual

Hide thumbs Also See for ColorSource PAR:

Advertisement

Quick Links

ETC Installation Guide
ColorSource
Overview
The ColorSource PAR is an affordable LED wash fixture that uses the RGB-L (red, green, blue, and
lime) color system to provide a rich, bright light.
265mm
6.1"
154.9mm
CAUTION:
Environment
The ColorSource PAR operates in ambient temperatures of 0°- 40°C and it comes with a variable-
speed fan.
Note:
Electrical
WARNING:
• Operates between 100V and 240VAC at a frequency of 50/60Hz.
• Up to 9 luminaires (15A max) may be linked via power thru connector (10 luminaires total
per circuit) when used with an R20 relay module or Unison Echo Relay Panel. Consult breaker
trip curves when used with other equipment. Requires power from a non-dimmable source.
Installation
Mounting hardware
The ColorSource PAR ships with a standard yoke. An
expandable floor stand yoke is available as an optional
accessory. Contact your local dealer for more information.
Corporate Headquarters
London, UK
Tel +44 (0)20 8896 1000
Rome, IT
Tel +39 (06) 32 111 683
Holzkirchen, DE
Hong Kong
Tel +852 2799 1220
Web:
www.etcconnect.com
7412M2100
Rev C
ColorSource PAR
PAR
18.7"
475.2mm
14.3"
362.2mm
4.3"
10.4"
110mm
• Risk of eye injury. Do not stare directly into the light.
• Do not operate in proximity to flammable materials.
The ColorSource PAR is for indoor use only.
Disconnect the fixture from power and DMX and allow it to cool before
performing any cleaning and maintenance.
Middleton, WI, USA
Tel +608 831 4116
Service: (UK)
Service: (UK)
service@etceurope.com
Tel +49 (80 24) 47 00-0
Service: (DE)
Service: (Asia)
service@etcasia.com
© 2015 ETC. All Rights Reserved.
Released 2015-04
ETC intends this document to be provided in its entirety.
12.2"
309.8mm
8.2"
207.7mm
4.0"
102.5mm
4.8"
121.8mm
9.5"
241mm
Service: (Americas)
service@etceurope.com
techserv-hoki@etcconnect.com
Product information and specifications subject to change.
Page 1 of 4
16.6"
422.8mm
7.8"
199mm
8.2"
209mm
9.9"
251mm
Safety cable
attachment
loop
service@etcconnect.com
Electronic Theatre Controls, Inc.

Advertisement

loading
Need help?

Need help?

Do you have a question about the ColorSource PAR and is the answer not in the manual?

Questions and answers

Summary of Contents for ETC ColorSource PAR

  • Page 1 ETC Installation Guide ™ ColorSource Overview The ColorSource PAR is an affordable LED wash fixture that uses the RGB-L (red, green, blue, and lime) color system to provide a rich, bright light. 16.6" 18.7" 422.8mm 475.2mm 12.2" 14.3" 309.8mm 362.2mm 8.2"...
  • Page 2: Fixture Setup

    This fixture is not Ethernet/data network compatible. Note: The ColorSource PAR is not self terminating. You must terminate the last fixture in line with a 120 ohm resistor. XLR terminators are not available from ETC. To purchase an RJ45 terminator, please contact your ETC customer service representative and request part number N4086.
  • Page 3: Dmx Addressing

    ETC Installation Guide ColorSource PAR • The DMX address will blink when no DMX is present and a preset or sequence is not active. The inactivity time-out is disabled while in a data loss state. • After five seconds of inactivity when DMX is present, the display goes dark.
  • Page 4: Power Consumption

    • CAL: Indicates a problem with the color calibration. The fixture will need to be returned to the ETC factory; contact your local dealer to setup a repair. • OtP: Indicates that the fixture has gone into over-temperature protection mode to avoid damaging the fixture.