Table of Contents
Advertisement
T8611G CHRONOTHERM
Programming the First Day
Start by programming the Wake time and temperature (and
fan operation on select models) for any one day:
1. Press Wake.
Time
Set Program
Run
Set Current
Wake
Leave
Return
Program
Day/Time
Wake
Heat/Cool
Hold Temp
Day
System
Settings
Daylight
Copy
Time
2. Press Day until the desired day is displayed.
Time
Set Program
Run
Set Current
Wake
Leave
Return
Program
Day/Time
Day
Heat/Cool
Hold Temp
Day
Settings
System
Daylight
Copy
Time
3. Press Time
or Time
displayed.
NOTE: The program times are in fifteen minute
intervals. (Example: 8:00, 8:15, 8:30).
Time
Time
Set Program
Run
Set Current
Leave
Day/Time
Wake
Return
Program
Heat/Cool
Hold Temp
Day
System
Settings
Daylight
Copy
Time
4. Press increase
or decrease
Wake temperature is displayed.
NOTE: The setpoint temperature range is 40 to 90°F
(7 to 31°C) for heating and 45 to 99°F (9 to
37°C) for cooling.
Time
Set Program
Run
Set Current
Wake
Leave
Return
Program
Day/Time
Heat/Cool
Hold Temp
Day
System
Settings
Daylight
Copy
Time
NOTE: Press Fan to modify fan operation. Auto means
the fan will run only when the heating or
cooling equipment is operating. On means the
fan will run continuously for the entire period.
5. Press Heat/Cool Settings to switch to other system
temperature setpoint.
NOTE: The program times are the same for both
heating and cooling.
Heat/Cool
Time
Set Program
Run
Set Current
Wake
Leave
Return
Program
Day/Time
Settings
Heat/Cool
Hold Temp
Day
System
Settings
Daylight
Copy
Time
68-0165—1
®
IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTAT
Setting
Set Program
Start Time
AM
Tue
Heat
Sleep
Wake
System
Fan
Fan
Heat
Auto
M10317
Setting
Set Program
Start Time
AM
Mon
Heat
Sleep
Wake
System
Fan
Fan
Heat
Auto
M10318
until the desired Wake time is
Set Program
Start Time
Setting
AM
Mon
Heat
Sleep
Wake
System
Fan
Fan
Heat
Auto
M10319
key until the desired
Set Program
Start Time
Setting
AM
Mon
Heat
Sleep
Wake
System
Fan
Fan
Heat
Auto
M10320
Setting
Set Program
Start Time
AM
Mon
Cool
Sleep
Wake
System
Fan
Fan
Heat
Auto
M10321
6. Press increase
or decrease
temperature setpoint is displayed.
Time
Set Current
Run
Wake
Program
Day/Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
7. Press Leave, Return or Sleep and repeat steps 3, 4, 5
and 6 for programming the rest of the day. The first day
is now programmed.
IMPORTANT
Repeat steps 1 through 7 for each day of the week
that has a different program than the first day. Refer
to Copying a Day section to copy any program day to
another.
8. Press Run Program when all days are programmed.
Time
Run
Run
Set Current
Wake
Program
Day/Time
Program
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
Copying a Day
NOTE: The thermostat must be in the program mode to use
the copy feature. Go to step 2. if the thermostat is
already in the program mode.
1. Press Wake.
Time
Set Current
Run
Wake
Wake
Program
Day/Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
2. Press Day to select the day to be copied if different from
the day displayed.
Time
Run
Set Current
Wake
Day/Time
Program
Day
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
3. Press Copy.
Copy
Time
Run
Set Current
Wake
Program
Day/Time
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
4. Press Day until the day to be copied to is displayed.
Time
Run
Set Current
Wake
Program
Day/Time
Day
Heat/Cool
Hold Temp
Day
Settings
Daylight
Copy
Time
14
key until the desired
Set Program
Start Time
AM
Set Program
Mon
Cool
Leave
Return
Sleep
Wake
System
Fan
System
Fan
Heat
AM
Set Program
Tue
Leave
Return
Sleep
Wake
System
DST
Fan
System
Fan
Heat
Set Program
Start Time
AM
Set Program
Tue
Heat
Leave
Return
Sleep
Wake
System
Fan
System
Fan
Heat
Set Program
Start Time
AM
Set Program
Mon
Heat
Leave
Return
Sleep
Wake
System
Fan
System
Fan
Heat
Set Program
Mon
Leave
Return
Sleep
System
Fan
Set Program
Mon
Wed
Leave
Return
Sleep
System
Fan
Setting
Auto
M10322
Room
Auto
M10323
Setting
Auto
M10324
Setting
Auto
M10325
M10326
M10327
Hide quick links:
Advertisement
Table of Contents
