JUKI lbh-1790 series Engineer's Manual page 143

INITIAL VALUE DATA FOR EACH SHAPE TABLE
No. Item
S01 Sewing shape
S02 Cloth cutting length
S03 Knife groove width, right
S04 Knife groove width, left
S05 Overedging width, left
S06 Left/right shape ratio (right side in terms of left side)
S07 Pitch at parallel section
S08 2nd bar-tacking length
S09 1st bar-tacking length
S10 Bar-tacking width, right compensation
S11 Bar-tacking width, left compensation
S12 Flow bar-tacking offset, left
S13 Flow bar-tacking offset, right
S14 Eyelet shape length
S15 Number of stitches of eyelet shape
S16 Eyelet width
S17 Eyelet length
S18 Round type shape length
S19 Number of stitches of radial shape
S20 Radial shape reinforcement (with/without)
S21 Pitch at bar-tacking section
S22 1st clearance
S23 2nd clearance
S31 1/2 stitching
S32 Double stitching cross selection
S33 Double stitching width compensation
S34 Number of times of basting
S35 Pitch of basting
S36 Rolling length of basting
S37 Rolling pitch of basting
S38 Rolling width of basting
S39 Compensation before/after needle entry of basting
S40 Compensation left/right needle entry of basting
S41 Compensation of left side position of basting
S42 Compensation of right side position of basting
S44 Speed setting of basting
S45 Sewing together function (without/with)
S46 Width of sewing together
S47 Pitch of sewing together
S51 Left parallel section tension
S52 Right parallel section tension
S53 Left parallel section tension (1st cycle of double stitching)
S54 Right parallel section tension (1st cycle of double stitching)
S55 1st bar-tacking section tension
S56 2nd bar-tacking section tension
S57 Setting of needle thread tension at sewing start
S58 Setting of needle thread tension of basting
S59 ACT timing adjustment at 1st bar-tacking start
S60 ACT timing adjustment at the start of right overedging
S61 ACT timing adjustment at 2nd bar-tacking start
S62 Number of stitches of tie stitching at the start of sewing
S63 Sewing pitch of tie stitching at the start of sewing
S64 Tie stitching width at sewing start
S65 Lengthwise compensation of tie stitching at the start of sewing
S66 Crosswise compensation of tie stitching at the start of sewing
S67 Tie stitching width at sewing end
S68 Number of stitches of tie stitching at sewing end
S69 Lengthwise compensation of tie stitching at the end of sewing
S70 Crosswise compensation of tie stitching at the end of sewing
S81 Knife motion (With/without)
S83 Knife at 1st cycle of double stitching (Without/with)
S84 Max. speed limitation
S86 Pitch of going
S87 Width of going
S88 Pitch of returning
S89 Width of returning
Unit
mm 12.7 12.7 12.7 12.7 12.7 12.7 12.7
mm 0.10 0.10 0.10 0.10 0.10 0.10 0.10
mm 0.10 0.10 0.10 0.10 0.10 0.10 0.10
mm 1.70 1.70 1.70 1.70 1.70 1.70 1.4
% 100 100 100 100 100 100 100
mm 0.35 0.35 0.35 0.35 0.35 0.35 0.35
mm 1.0 – 1.0 – 1.5 3.0 1.0
mm 1.0 – – – – – –
mm 0.0 – 0.0 – 0.0 – 0.0
mm 0.0 – 0.0 – 0.0 – 0.0
mm – – – – – 0.85 –
mm – – – – – 0.85 –
mm – – – – – – 2.0
Stitch – – – – – – 3
mm – – – – – – 1.0
mm – – – – – – 3.0
mm – 2.0 2.0 2.0 2.0 2.0 –
Stitch – – 3 3 3 3 –
– – Without Without Without Without – Without
mm 0.30 0.30 0.30 Å[ 0.30 0.30 0.30
mm 1.5 1.5 1.5 1.5 1.5 1.5 1.5
mm 1.3 1.3 1.3 1.3 1.3 1.3 1.3
Single Single Single Single Single Single Single
< < < < < < <
mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0
Time 0 0 0 0 0 0 0
mm 4.0 4.0 4.0 4.0 4.0 4.0 4.0
mm 8.0 8.0 8.0 8.0 8.0 8.0 8.0
mm 0.8 0.8 0.8 0.8 0.8 0.8 0.8
mm 1.5 1.5 1.5 1.5 1.5 1.5 1.5
mm 1.5 1.5 1.5 1.5 1.5 1.5 1.5
mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0
mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0
mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0
rpm 2000 2000 2000 2000 2000 2000 2000
Without Without Without Without Without Without Without Without
mm 2.0 2.0 2.0 2.0 2.0 2.0 2.0
mm 2.0 2.0 2.0 2.0 2.0 2.0 2.0
120 60 120 120 120 120 60
120 60 120 120 120 120 60
60 60 60 60 60 60 60
60 60 60 60 60 60 60
35 60 120 35 35 35 60
35 60 35 35 35 35 60
25 25 25 25 25 25 25
80 80 80 80 80 80 80
Stitch 0 0 0 0 0 0 0
Stitch 0 0 0 0 0 0 0
Stitch 0 0 0 0 0 0 0
Stitch 3 3 3 3 3 3 3
0.00 0.00 0.00 0.00 0.00 0.00 0.00
mm 0.6 0.6 0.6 0.6 0.6 0.6 0.6
mm 0.0 1.5 0.0 1.5 0.0 0.0 0.0
mm 0.0 0.0 0.0 0.0 0.0 0.7 0.0
mm 0.6 0.6 0.6 0.6 0.6 0.6 0.6
Stitch 3 3 3 3 3 3 3
mm 0.0 0.0 0.0 0.0 0.0 0.0 0.0
mm 0.9 0.9 0.9 0.9 0.0 0.7 0.9
With With With With With With With
Without Without Without Without Without Without Without Without
rpm 3600 3600 3600 3600 3600 3600 3600
mm – – – – – – –
mm – – – – – – –
mm – – – – – – –
mm – – – – – – –
Shape selection Level 1 (12 shapes)
12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7
0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10
0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10
1.4 1.4 1.4 1.70 1.70 1.70 1.70 1.70 1.4
100 100 100 100 100 100 100 100 100
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
– 1.5 3.0 – 1.0 1.0 1.5 3.0 –
– – – – – – – – –
– 0.0 – – 0.0 0.0 0.0 – –
– 0.0 – – 0.0 0.0 0.0 – –
– – 0.85 – – – – 0.85 –
– – 0.85 – – – – 0.85 –
2.0 2.0 2.0 – – – – – 2.0
3 3 3 – – – – – 3
1.0 1.0 1.0 – – – – – 1.0
3.0 3.0 3.0 – – – – – 3.0
2.0 – – 2.0 2.0 2.0 2.0 2.0 2.0
3 – – – – – – – –
– – – – – – – –
– 0.30 0.30 0.25 0.30 0.25 0.25 0.25 0.25
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3
Single Single Single Single Single Single Single Single Single
< < < < < < < < <
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0 0 0 0 0 0 0 0 0
4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0
8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0
0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
2000 2000 2000 2000 2000 2000 2000 2000 2000
Without Without Without Without Without Without Without Without
2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
60 60 60 60 60 60 60 60 60
60 60 60 60 60 60 60 60 60
60 60 60 60 60 60 60 60 60
60 60 60 60 60 60 60 60 60
60 60 60 60 60 60 60 60 60
60 60 60 60 60 60 60 60 60
25 25 25 25 25 25 25 25 25
80 80 80 80 80 80 80 80 80
0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
3 3 3 3 3 3 3 3 3
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.5 0.0 0.0 1.5 0.0 0.0 0.0 0.0 1.5
0.0 0.0 0.7 0.0 0.0 0.0 0.0 0.7 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
3 3 3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.9 0.0 0.7 0.9 0.9 0.9 0.0 0.7 0.9
With With With With With With With With With
Without Without Without Without Without Without Without Without
3600 3600 3600 3600 3600 3600 3600 3600 3600
– – – – – – – – –
– – – – – – – – –
– – – – – – – – –
– – – – – – – – –
Shape selection Level 2 (20 shapes)
12.7 12.7 12.7 12.7 12.7 12.7 12.7 12.7
0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10
0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10
1.4 1.70 1.70 1.70 1.70 1.70 1.70 1.70
100 100 100 100 100 100 100 100
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
– – – – 1.5 3.0 – –
– 1.0 1.0 1.0 1.0 1.0 – –
– 0.0 0.0 0.0 0.0 0.0 – –
– 0.0 0.0 0.0 0.0 0.0 – –
– – – – – 0.85 – –
– – – – – 0.85 – –
2.0 – – – – – – –
3 – – – – – – –
1.0 – – – – – – –
3.0 – – – – – – –
2.0 2.0 2.0 2.0 – – 2.0 2.0
– 3 – – – – 3 3
– Without – – – – Without Without
0.30 0.30 0.25 0.30 0.30 0.30 0.25 0.30
1.5. 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.3 1.3 1.3 1.3 1.3 1.3 1.3 1.3
Single Single Single Single Single Single Single Single
< < < < < < < <
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0 0 0 0 0 0 0 0
4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0
8.0 8.0 8.0 8.0 8.0 8.0 8.0 8.0
0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
2000 2000 2000 2000 2000 2000 2000 2000
Without Without Without Without Without Without Without Without
2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
60 120 60 60 60 60 60 60
60 120 60 60 60 60 60 60
60 60 60 60 60 60 60 60
60 60 60 60 60 60 60 60
60 30 60 60 60 60 60 60
60 120 60 60 60 60 60 60
25 25 25 25 25 25 25 25
80 80 80 80 80 80 80 80
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
3 3 3 3 3 3 3 3
0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.5 1.5 1.5 1.5 0.0 0.0 1.5 1.5
0.0 0.0 0.0 0.0 0.0 0.7 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
3 3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.9 0.9 0.9 0.9 0.0 0.7 0.9 0.9
With With With With With With With With
Without Without Without Without Without Without Without Without
3600 3600 3600 3600 3600 3600 3600 3600
– – – – – – – –
– – – – – – – –
– – – – – – – –
– – – – – – – –
Shape selection Level 3 (30 shapes)
12.7 12.7 13.0 19.1 19.1 19.1
0.10 0.10 – – 0.10 0.10
0.10 0.10 – 0.10 – 0.10
1.70 1.70 – – – –
100 100 – – – –
0.35 0.35 – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
– – – – – –
2.0 2.0 – – – –
3 – – – – –
Without – – – – –
0.25 0.25 – – – –
1.5 1.5 – 2.0 2.0 2.0
1.3 1.3 – 2.0 2.0 2.0
Single Single – – – Single
< < – – – <
0.0 0.0 – – – –
0 0 3 2 2 –
4.0 4.0 4.0 4.0 4.0 –
8.0 8.0 8.0 8.0 8.0 –
0.8 0.8 0.8 0.8 0.8 –
1.5 1.5 1.5 1.5 1.5 –
1.5 1.5 1.5 1.5 1.5 –
0.0 0.0 0.0 0.0 0.0 –
0.0 0.0 0.0 0.0 0.0 –
0.0 0.0 0.0 0.0 0.0 –
2000 2000 2000 2000 2000 –
Without Without – – – –
2.0 2.0 – – – –
2.0 2.0 – – – –
60 60 60 60 60 60
60 60 60 60 60 60
60 60 – – – –
60 60 – – – –
60 60 – – – –
60 60 – – – –
25 25 25 25 25 25
80 80 80 80 80 ---
0 0 – – – –
0 0 0 0 0 0
0 0 – – – –
3 3 3 3 3 3
0.00 0.00 0.00 0.00 0.00 0.00
0.6 0.6 0.6 0.6 0.6 0.6
1.5 1.5 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6
3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0
0.9 0.9 0.0 0.0 0.0 0.0
With With – With With With
Without Without – – – –
3600 3600 3600 3600 3600 3600
– – 0.80 0.80 0.80 0.80
– – 1.7 1.7 1.7 1.7
– – 0.80 0.80 0.80 0.80
– – 1.7 1.7 1.7 1.7