Using An Extension Cable - Stanley STDH8013 Instruction Manual

f Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods ensure you take
regular breaks.
f Impairment of hearing.
f Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)

USING AN EXTENSION CABLE

If an extension cable is requred, use an approved extension
cable suitable for the power input of this tool (see technical
data). The minimum conductor size is 1.5 mm
When using a cable reel, always unwind the cable
completely. Also refer to the table below.
Conductor size (mm )
2
0.75
1.00
1.50
2.50
4.00
Voltage Amperes
115 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230 0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
FEATURES (Fig. A)
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Mode selector
5. Ventilation slots
6. Side handle
7. Depth adjustment rod
8. Keyed chuck
9. Sleeve
10. Chuck key
11. Speed dail
ASSEMBLY
Warning! Before assembly, please ensure that the
power tool is powered off and the power plug of the tool is
unplugged from the power source.
.
2
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5 15 25 30 45
Cable rating (Amperes)
6 6 6 6
6 6 6 6
6 6 10 15
10 10 15 20
15 15 20 25
20 20 25 -
6 6 6 6
6 6 6 6
6 6 6 6
10 10 10 10
15 15 15 15
20 20 20 20
Selecting the operating mode (FIG. B)
The tool can be used in two operating modes:
Rotary drilling: for steel, wood and plastics.
Impact drilling: simultaneous rotating and impacting
for concrete and masonry drilling operations.
f Select the required operating mode by rotating the
mode selector (4) to the required position.
Inserting and removing a bit (FIG. A)
Keyed chuck
f Open the chuck by turning the sleeve (9)
counterclockwise and insert the bit shank.
f Put the chuck key (10) into each hole in the side of
the chuck and turn clockwise until tight.
f To remove the bit, proceed in reverse order.
Fitting the side handle (FIG. A)
The side handle (6) can be fitted to suit both RH- and
LH-users.
60
Warning! Always use the drill with the side handle
properly assembled.
6 10
f Loosen the side handle.
15 15
f For RH-users, slide the side handle clamp over-
20 20
the collar behind the chuck, handle at the left.
20 25
f For LH-users, slide the side handle clamp over-
25 -
the colar behind the chuck, handle at the right.
- -
f Rotate the side handle to the desired position-
6 6
and tighten the handle.
6 6
10 15
Setting the drilling depth (FIG. C)
15 15
f Insert the required drill bit into the chuck.
20 20
f Slacken the side handle (6).
25 -
f Fit the depth adjustment rod (7) through the
hole in the side handle clamp.
f Adjust the drilling depth as shown.
f Tighten the side handle.
Forward/reverse slider (FIG. A)
f To select forward or reverse rotation, use the forward/
reverse-switch (3) (see arrow on tool).
Warning! Always wait until the motor has come to
a complete standstill before changing the direction of
rotation.
Chuck removal (FIG. D)
f Open the chuck jaws as far as possible
f Insert a screwdriver into the chuck and remove the
chuck retaining screw (12) by turning clockwise
f Tighten an Allen key into the chuck and strike it
with a hammer as shown.
ENGLISH • 17