Subscribe to Our Youtube Channel
Related Manuals for Hilti DX 460 SM
Summary of Contents for Hilti DX 460 SM
- Page 1 DX 460 SM Operating instructions Mode d’emploi Manual de instrucciones Инструкция по зксплуатации Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01...
- Page 2 Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01...
- Page 3 DX 460 MX SM DX 460 Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01...
- Page 4 DX 460 DX 460 DX 460 DX 460 DX 460 DX 460 DX 460 MX SM Steel base material Untergrund Stahl min. max. C L I C K Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01...
-
Page 5: Table Of Contents
● Do not operate the tool in an explosive or flammable 4. Accessories atmosphere, unless the tool is approved for such use. 5. Technical data ● To avoid the risk of injury, use only original Hilti fas- 6. Before use teners, cartridges, accessories and spare parts or those 7. Operation of equivalent quality. -
Page 6: General Information
● Store cartridges and unused tools unloaded, in a dry, material, hollow brick, glazed tile, thin-gauge sheet met- al (< 4 mm), grey cast iron, spheroidal cast iron and gas high or locked place out of the reach of children. concrete. -
Page 7: Description
This to it when making an inquiry to your Hilti representative prevents the Hilti DX tool from firing when it is dropped or service department. onto a hard surface, no matter at which angle the impact occurs. -
Page 8: Accessories
* Due to variations in site conditions, site testing required. Note: Refer to the nail/cartridge selector chart for more detail information. Contact your local Hilti marketing organiza- tion for technical support with diaphragm design calculations and project submittals. Fastener program: For approval relevant roof and floor decking applications (SDI, ICBO, FM, UL approved): Article no. - Page 9 Fastening guidelines For more specific information, refer to the Product Technical Guide, which is available from your local Hilti orga- nization or if necessary, your national technical regulations. Note: The MX SM magazine and associated fasteners are only suitable for fastenings on steel! Steel: ″)
-
Page 10: Technical Data
DX 460 tool. when the controls do not operate properly. If necessary, have the tool repaired at a Hilti service centre. ● Check the buffer and piston for wear (see 8. Care and Fitting the DX 460 SM to the standup handle X-SH 460 maintenance). -
Page 11: Operation
7. Operation Unload / Reload the MX SM fastener magazine 1. Ensure that there is no cartridge strip in the tool. If there is a cartridge strip in the tool, remove it by hand from the tool. 2. To unload unused fasteners turn the unload button at a right angle position to the magazine. -
Page 12: Care And Maintenance
– Wash your hands after cleaning the tool 2. To disassemble the exhaust gas return unit from the DX 460 SM tool unlock the push button on the grip Daily maintenance and inspection / Cleaning section of the tool and servicing (minor service) 3. -
Page 13: Malfunctions, Remedies And Troubleshooting
If the tool then still displays big variations in driving power or penetration depths, please contact your Hilti representative. Piston does not return when the joist or beam is missed: Pull the cartridge strip out of the tool. Push back the... - Page 14 ■ Clean the cartridge strip guide- way (see 8.4, point 5) If the problem persists: ■ Tool damaged ■ Contact Hilti Center. ■ Tool overheated because of high ■ Let the tool cool down Cartridge strip cannot be ■ Then carefully try to remove the...
-
Page 15: Disposal
■ Carbon build-up 10. Disposal Most of the materials from which Hilti power actuated tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrange- ments for taking back your old powder actuated tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. -
Page 16: Manufacturer's Warranty - Dx Tools
(PTB, Braun- The Hilti DX 460 has been system and type tested. As a schweig)) and to the Office of the Permanent Interna- result, the tool bears the square approval mark showing tional Commission (C.I.P.) (Permanent Internationial... -
Page 17: Health And Safety Of The User
Vibration The declared total vibration value according to 2006/42/EC does not exceed 2.5 m/s Further information regarding the health and safety of the user can be found at the Hilti web site: www.hilti.com/hse Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01... - Page 18 Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01...
- Page 19 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2713 | 0713 | 10-Pos. 3 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 371686 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5129667 / 000 / 01...
Need help?
Do you have a question about the DX 460 SM and is the answer not in the manual?
Questions and answers