Related Manuals for Hilti DX 460 GR
Summary of Contents for Hilti DX 460 GR
- Page 1 DX 460 GR Bedienungsanleitung Operating instructions Mode d’emploi Istruzioni d’uso Manual de instruções Manual de instrucciones Οδηγιες χρησεως Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01...
- Page 2 Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01...
- Page 3 Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01...
- Page 4 8.10 8.11 8.12 8.13 C L I C K Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01...
- Page 5 8.14 Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01...
-
Page 6: Table Of Contents
9. Troubleshooting ● To avoid the risk of injury, use only original Hilti fas- 10. Disposal teners, cartridges, accessories and spare parts or those 11. Manufacturer's warranty – DX Tools of equivalent quality. - Page 7 Have the tool checked and repaired if necessary at per, natural rock, insulation material, hollow brick, glazed a Hilti repair center. tile, thin-gauge sheet metal (< 4 mm), grey cast iron, ● Never attempt to pry a cartridge from the magazine spheroidal cast iron and gas concrete.
-
Page 8: General Information
This Type: DX460 GR prevents the Hilti DX tool from firing when it is dropped onto a hard surface, no matter at which angle the impact occurs. The trigger safety device ensures that the cartridge Serial no.:... - Page 9 The tool can be fired only when pressed ful- ly against the work surface in this way. In addition, all Hilti DX tools are equipped with an unin- tentional firing safety device . This prevents the tool from firing if the trigger is pulled and the tool then pressed against the work surface.
-
Page 10: Accessories
6.8/11 M red Heavy 6.8/11 M black Black/purple Extra heavy Cleaning set Hilti spray, flat brush, large round brush, small round brush, scraper, cleaning cloth. Hilti recommendations for grating application areas Application areas X-FCM + X-EM X-FCM-M + X-CRM X-FCM-R + X-CRM... -
Page 11: Technical Data
Do not operate the tool when parts are damaged or when the controls do not operate properly. If necessary, have the tool repaired at a Hilti service centre. ● Check the buffer and piston for wear (see “8. Care and maintenance”). -
Page 12: Operation
● Never attempt to drive a fastener in an existing hole tool could be made ready to fire by pulling back the fastener guide except where recommended by Hilti, e.g. when using or the fastener by hand. the DX X-BT system. -
Page 13: Care And Maintenance
● Never use grease for maintenance/lubrication of tool parts. This may strongly affect the functionality of the tool. Use only Hilti spray or such of equivalent quality. ● Dirt from DX tool contains substances that could be endangering your health. - Page 14 1. Use the large round brush to clean inside the hous- ● excessive, uneven wear beneath the metal ring is ing. noticed. 2. Spray the inside of the housing lightly with Hilti spray. Replace the piston if: 8.11 Clean the cartridge strip guideway ●...
-
Page 15: Troubleshooting
■ Clean the cartridge strip guide- way (see 8.11) If the problem persists: ■ Tool damaged ■ Contact Hilti Repair Centre ■ Tool overheated because of high ■ Let the tool cool down and then Cartridge strip cannot be setting rate... - Page 16 (see 8.4). ■ Damaged buffer If the problem persists: ■ Contact Hilti Repair Centre ■ Carbon build-up ■ Carbon build-up ■ Manually pull the front part of Piston return unit is stuck the piston return unit out of the tool ■...
-
Page 17: Disposal
O.K. 10. Disposal Most of the materials from which Hilti power actuated tools are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrange- ments for taking back your old powder actuated tools for recycling. Please ask your Hilti customer service department or Hilti sales representative for further information. -
Page 18: Manufacturer's Warranty - Dx Tools
(PTB, Braun- The Hilti DX 460 has been system and type tested. As a schweig)) and to the Office of the Permanent Interna- result, the tool bears the square approval mark showing tional Commission (C.I.P.) (Permanent Internationial... -
Page 19: Health And Safety Of The User
The declared total vibration value according to 2006/42/EC does not exceed 2.5 m/s Further information regarding the health and safety of the user can be found at the Hilti web site: www.hilti.com/hse Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01... - Page 20 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 2678 | 0613 | 5-Pos. 2 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 282819 / A3 Printed: 12.08.2013 | Doc-Nr: PUB / 5129640 / 000 / 01...