XPROHELI Spektrum DX8i User Manual

For the xp2 quadcopter with gps

Hide thumbs

page of 18

/ 18
Bookmarks

Quick Links

Download this manual

User Manual

XProHeli XPG Brushless Gimbal

TheAppTimes

[

SPEKTRUM DX8i Programming

]

Instructions for XP2 Quadcopter GPS

This user manual provides information on the specifications, programming and functions of

the SPECTRUM DX8i Radio transmitter for the XP2 Quadcopter with GPS.

XP2 Quadcopter GPS

Page i

Summary of Contents for XPROHELI Spektrum DX8i

Page 1 SPEKTRUM DX8i Programming Instructions for XP2 Quadcopter GPS This user manual provides information on the specifications, programming and functions of the SPECTRUM DX8i Radio transmitter for the XP2 Quadcopter with GPS. XP2 Quadcopter GPS Page i ©2014 XPROHELI. All Rights Reserved.
Page 2 User Manual XProHeli XPG Brushless Gimbal Programing Guide for Spektrum DX8i with GPS 1. Carefully unbox radio and contents. 2. Internal battery in the DX8 radio will be partially charged out of box, be sure to fully charge the radio prior to flying.
Page 3 6. Hold the menu select roller down on radio and turn on. Power on - > HOLD DOWN 7. Scroll down to system setup and put model type as Airplane and the model name as XP2 GPS. XP2 Quadcopter GPS Page 1 ©2014 XPROHELI. All Rights Reserved.
Page 4 Aux2. If you would like to control the tilt with the Knob you will have to set Knob to Aux3. 9. Exit out to Main Screen, Radio will restart, press down roll button to enter the Function List. XP2 Quadcopter GPS Page 2 ©2014 XPROHELI. All Rights Reserved.
Page 5 11. With the props off of your XP2, Connect your NAZA controller to the computer and plug in your flight battery. If this is your first time XP2 Quadcopter GPS Page 3 ©2014 XPROHELI. All Rights Reserved.
Page 6 After the upgrade the bar at the bottom will blink from red to green. Unplug the flight battery, then plug back in to restart the controller. 13. Go to Motor Mixer on computer and select Quad-rotor x. XP2 Quadcopter GPS Page 4 ©2014 XPROHELI. All Rights Reserved.
Page 7 X as -8 cm, Y as 8 cm, and Z as -1 cm. 15. Go to RC Tab and select Tradition and then go to Advanced – Motor tab and set to Immediately XP2 Quadcopter GPS Page 5 ©2014 XPROHELI. All Rights Reserved.
Page 8 If they do not correspond, click the buttons on the right side to switch. See: http://community.xproheli.com/training/naza-software-updates additional video tutorial. XP2 Quadcopter GPS Page 6 ©2014 XPROHELI. All Rights Reserved.
Page 9 Using the F mode toggle (3 way switch left side of controller) adjust the percentages both to 84% for now. This will be checked later. 18. Select Aux 1 and make sure both percentages are 100%. XP2 Quadcopter GPS Page 7 ©2014 XPROHELI. All Rights Reserved.
Page 10 Manual. Also check that the failsafe is activating correctly by flipping the return to home switch (back right two-way switch), the indicator on the slider should move and highlight in blue the failsafe mode. XP2 Quadcopter GPS Page 8 ©2014 XPROHELI. All Rights Reserved.
Page 11 21. Go to the RC tab once again and verify that the Flap switch for AUX 2 is operating X2 in the Naza software correctly (low med high) XP2 Quadcopter GPS Page 9 ©2014 XPROHELI. All Rights Reserved.
Page 12 GPS calibration video link: https://www.youtube.com/watch?v=xF5-H0SwBt4 Once the calibration is complete, connect your NAZA back to your computer to verify the course lock / home lock function is activating correctly. XP2 Quadcopter GPS Page 10 ©2014 XPROHELI. All Rights Reserved.
Page 14 102% for the right side. OPTIONAL: To setup XPG tilt set AUX 3 left 100% right 29%, then set the Subtrim to -67%. See the DX8 XPG tilt video at: http://xproheli.com/pages/training XP2 Quadcopter GPS Page 12 ©2014 XPROHELI. All Rights Reserved.
Page 15 0% and the one below to -54% OPTIONAL: To Setup the mix to control the tilt of the XPG gimbal on the FLAP switch change the mix to AX2 > GER XP2 Quadcopter GPS Page 13 ©2014 XPROHELI. All Rights Reserved.
Page 16 30. Next we will set the control sticks EXPO settings, this is optional but is highly recommended for everyone. 31. To set the EXPO settings go to the Function List and scroll down to select D/R and Expo XP2 Quadcopter GPS Page 14 ©2014 XPROHELI. All Rights Reserved.
Page 17 User Manual XProHeli XPG Brushless Gimbal 32. Set Aileron as follows: 33. On the channel (Chan) select Elevator and set as follows: XP2 Quadcopter GPS Page 15 ©2014 XPROHELI. All Rights Reserved.
Page 18 System Setup menu. Scroll down to Transfer SC Card. Go to Select Option and select. Scroll to Export Model. Then select Export at the bottom. XP2 Quadcopter GPS Page 16 ©2014 XPROHELI. All Rights Reserved.