Advertisement
MAINTENANCE OF REMOTE CONTROL
Before using the remote control, pull out the insulating patch. This
patch was installed to insulate the battery from draining until ready to use.
BATTERY INFORMATION:
Lithium Battery: CR2025 3V
Battery Life: Approximately 6 months.
Replacing the Battery from the Remote Control:
1) Remove the battery holder by pressing the locking tab with your thumb
and pulling it out.
2) Replace the battery with the same type and the
3) Gently push in the holder until securely locked into place.
WARNING:
Do not recharge, disassemble or dispose of in fire.
Battery leakage may cause damage to the unit.
To avoid the risk of accident, keep batteries out of reach of children.
WIRING DIAGRAM
ANTENNA PLUG
YELLOW
CONSTANT B+
7A FUSE
BLACK(GND)
FILTER BOX
IGNITION SWITCH
0.5A FUSE
RED (B+)
+
WHITE
FRONT
-
WHITE/BLACK
LEFT
LOUDSPEAKER
+
GREEN
-
REAR
GREEN/BLACK
Note:
1.Make sure use a speaker with 4 ohm load impedance.
2.Do not make the auto antenna wire and ground touch each other.
Page 7
+
side facing up.
RED R
RCA LINE OUT
WHITE L
FUSE 0.5A
BLUE AUTO ANT
+
FRONT
GRAY
-
GRAY/BLACK
RIGHT
+
LOUDSPEAKER
VIOLET
-
REAR
VIOLET/BLACK
9. BAND BUTTON
Press the BND button briefly to select the radio broadcasting band you would
like to hear. The AM/FM band is toggled cyclically through the tuning bands
->FM 1-> FM 2 -> FM 3 -> AM 1->AM 2 ->.
10. MODE BUTTON
When a disc is present in the CD slot, pressing the MODE button will allow you
to change to RADIO mode (and back). The LCD display information changes
with the mode (please note: when no disc is present in the unit, this button does
not provide a function).
11. MUTE BUTTON
This button serves to switch the MUTED state on/off.
Press the MUTE button to suppress the loudspeaker temporarily, and press
again to resume listening. The muted state will be also released when the
MODE, LOUD, SEL and VOL(+), VOL(-) button on the front panel is pressed.
12. INFRARED REMOTE CONTROL SENSOR
13. A.P BUTTON
a) Automatic store preset station memory:
During radio mode, press the A.P button and hold for longer than one
second to activate automatic station storage. The radio searches within the
current frequency band, and the six strongest signal stations are allocate to
the corresponding storage locations each band. The stations that have now
been stored will be played for approximately five seconds each time, then
the station storage location is set. The radio will finish the searching for and
storage, the preset channel number and the frequency will appear on the
display.
b) Automatic scan preset station memory:
After the A.P button has been pressed briefly, the radio scan all the pre-set
stations in the current frequency band. In FM band, FM 1, FM 2 and FM 3 is
checked on at a time.
14-19. PRESET STATION MEMORY AND TOP/>||, INT, RPT, RDM BUTTONS
a) During radio mode:
Press the six buttons briefly directly selects a preset radio station.
If the six buttons are pressed for more than 2 seconds, the station currently
being listened to is memorized into the selected preset button.
b) During CD mode:
Press the >|| button briefly to interrupt the playback of the CD disc.
Press again to resume normal playback of the CD.
Press the TOP button and hold for approximately 2 seconds to play the first
track of the current disc.
Press the INT button to play the first 10 seconds part of each track.
Press again to stop scan, while the currently selected track will be played.
Press the RPT button to play the current track repeatedly.
Press again to cancel this function.
Press the RDM button to play all tracks on disc in random.
Press again to cancel this function.
Page 4
Advertisement
