Related Manuals for Jasic Cut 45P
Summary of Contents for Jasic Cut 45P
- Page 1 Cut 45P Air Plasma Cutting machine Order code ! JP-45P OPERATOR MANUAL...
- Page 2 Your new product Thank you for selecting this Jasic Technology, Wilkinson Star product. This product manual has been designed to ensure that you get the most from your new product. Please ensure that you are fully conversant with the information provided paying particular attention to the safety precautions. The information will help protect yourself and others against the potential hazards that you may come across.
-
Page 3: Safety Precautions
Safety Precautions These general safety norms cover both arc welding Insulate yourself from work and ground using dry insulating mats or covers big enough to prevent any physical contact machines and plasma cutting machines unless with the work ground. otherwise noted. Never touch the electrode if you are in contact with the work The equipment must only be used for the purpose it was ground, or another electrode from a different machine. - Page 4 Do not weld on coated metals, unless the coating is Replace the coverings and protections and close all doors removed from the weld area, the area is well ventilated, and when the intervention is finished, and before starting the while wearing an air-supplied respirator. The coatings on equipment.
- Page 5 Keep your head and face away from the cylinder valve outlet RF Declaration when opening the cylinder valve. Equipment that complies with directive 2004/108/EC Always secure the cylinder safely concerning electromagnetic compatibility (EMC) and the technical requirements of EN60974-10 is designed for use in Never deface or alter any cylinder industrial buildings and not those for domestic use where electricity is provided via the low voltage public distribution...
-
Page 6: Product Overview
Product Overview This is a digital plasma cutting machine with high Powerful cutting performance performance and using advanced technology. The CUT45P This machine is economical and practical since it can cut is an ultra-portable plasma cutting system suitable for a metals by using compressed air as the plasma gas source. -
Page 7: Technical Data
Technical data MODEL CUT45P Rated input voltage (V) 230V AC±15% Rated input frequency (Hz) 50/60 Rated input capacity (KVA) Recommended supply fuse (A) Compressed air requirement 0.45Mpa; 170L/Min. No load voltage 280V DC Cutting current (A) 20-45 Rated output voltage (V) Rated duty cycle (%) 45A @ 35% Efficiency (%) - Page 8 Controls PANEL LAYOUT FRONT REAR AIR PRESSURE GUAGE MAINS INPUT CABLE WORK RETURN CONNECTOR MAINS ON/OFF SWITCH TORCH CONNECTOR AIR INLET CONNECTION CURRENT CONTROL KNOB...
- Page 9 Front panel of CUT45P Symbol Function Power indicator: It illuminates when the machine is powered on, and it flashes after arc is successfully ignited. Overheating indicator: It illuminates when the working temperature of the IGBT is too high. When in this state, the machine stops working. Torch protection indicator: It illuminates when the consumable parts of the machine are incorrectly fitted or the torch head is shorted.
-
Page 10: Installation
Installation Unpacking Connection of cutting torch Check the packaging for any signs of damage. Connect the central connection plug on the cutting torch to the central connection socket of the power supply, and Carefully remove the machine and retain the packaging until tighten It clockwise to avoid gas leakage. - Page 11 current or inner temperature exceeds the set standard, the Operation of the reducer valve machine will stop automatically. However, excessive use (e.g. too high voltage) of machine may also damage the machine: Embedded filter reducer The embedded filter reducer is correctly set when leaving factory, and users do not need to set it themselves in general.
- Page 12 Operation It is recommended to initiate the cutting from the Before starting any cutting activity ensure that you have edge of workpiece, unless penetration is needed. suitable eye protection and protective clothing. Also take the necessary steps to protect any persons within the area.
-
Page 13: Maintenance And Troubleshooting
Maintenance and troubleshooting The following operation requires sufficient professional Troubleshooting knowledge on electric aspects and comprehensive Before arc cutting machines are dispatched from the factory, safety knowledge. Make sure the input cable of the they have already been checked thoroughly. The machine machine is disconnected from the electricity supply and should not be tampered with or altered. -
Page 14: Electrical Schematic
Electrical schematic... -
Page 15: Parts List
Parts list Cut 45P - (JP-45P) - Page 16 Heatsink 10048684 Cover 10048628 Thermal switch 10048681 Display panel 10037075 Insulating strip 10007295 Pressure guage 10050319 Main PCB 10041712 Jasic ident 10050326 Insulation 10037152 Quick connector socket 10037028 Support 10043926 Blanking plate 10048706 Base plate 10048633 Central connector 10006256 Rectifier...
- Page 17 JP-45P AIR PLASMA CUTTING MACHINE Order code ! JP-45P © Wilkinson Star Limited Issue 1 November 2014 Product is subject to change without notice...