Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pulsar VD53
Summary of Contents for Pulsar VD53
- Page 1 CAL. VD53 & VD54 CHRONOGRAPH CALIBER OF THREE HANDS WITH THREE EYES (MINUTES, 1/1 SECOND CHRONOGRAPH, 24-HUOR INDICATOR) TIME/CALENDAR l Hour, minute and second hands l Date displayed in numerals (VD53 only) STOPWATCH l Measures up to 60 minutes in one second increments.
-
Page 2: Screw Down Crown
1 Turn Crown counterclockwise until you no longer feel the threads turning. 2 Crown can be pulled out. STOPWATCH CROWN minute hand a b c Locking the crown 1 Push Crown back in to normal position. HOUR. Second hand 24 - hour hand 2 Turn Crown clockwise while pressing it lightly until tight. STOPWATCH second hand Date (VD53 only) a: Normal position b: First click c: Second click... -
Page 3: Time Setting
* If either of the STOPWATCH hands is not at the "0" position, reset them , following the procedure below: HOUR. CROWN Pull out to second click STOPWATCH minute hand Hour hand CROWN Date (VD53 only) Press A or B to reset the STOP- 1 Pull out to first click, and turn clockwise until the previous day’s date WATCH second and minute appears. (VD53 only) hands to the “0” position. 2 Pull out to second click when the second hand is at the 12 o’clock position. A: The hands move counterclockwise. The second hand will stop on the spot. And advance the hour and B: The hands move clockwise. minute hands by turning the crown. 3 Turn clockwise until the desired date appears. (VD53 only) 4 Turn to set the hour and minute hands. STOPWATCH Push back in to normal CROWN second hand 5 Push back in to normal position in accordance with a time signal. - Page 4 STOPWATCH Standard measurement l The stopwatch can measure up to 60 minutes in one second increments. l The measured time is indicated by the STOPWATCH hands that move inde- START RESET STOP pendently of the center and 24-hour hands. l Before using the stopwatch, be sure to check that the crown is set at the nor- mal position and that the STOPWATCH hands are reset to the “0” position. Accumulated elapsed time measurement * If the STOPWATCH hands do not return to the "0" position when the stopwatch is reset, follow the procedure in "STOPWATCH HAND POSITION ADJUSTMENT".
-
Page 5: Notes On Operating The Watch
Battery life : Approx. 2 years time and then turn it back to the exact minute. Years Battery : SEIKO SR920SW [Date setting (VD53 only)] It is necessary to adjust the date on the first day after a 30-day month and February. l If the stopwatch is used for more than 2 hours a day, the battery life may be less Do not set the date between 9:00 p.m. and 1:00 a.m., as the date may not change than the specified period. - Page 6 We recommend that you contact an AUTHORIZED PULSAR DEALER for battery l Necessary procedure after battery change replacement. After the battery is replaced with a new one, or in case any of the hands should move l After the battery is replaced with a new one, adjust the stopwatch hand position and STOPWATCH improperly, follow the procedure below to reset the hands to “0” po- set the time/calendar.
- Page 7 CAUTION l Water resistance (10 bar/15 bar/20 the watch becomes wet, we suggest that you bar)* have it checked by an AUTHORIZED PULSAR If “WATER RESISTANT 10 BAR”, The battery is not rechargeable. Never attempt to recharge it, as this DEALER or SERVICE CENTER. “WATER RESISTANT 15 BAR” or may cause battery leakage or damage to the battery.
-
Page 8: Periodic Check
* Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the CARE OF CASE AND BRACELET MAGNETISM crown is pushed in completely. Do not operate the crown when the watch is wet or in water. If used in sea water, Your watch will be ad- To prevent possible rusting of rinse the watch in fresh water and dry it completely.
Need help?
Do you have a question about the VD53 and is the answer not in the manual?
Questions and answers