Table of Contents
Advertisement
Display Unit Setup
The display unit operates with batteries and/or power adapter. Regardless of
the power source, it is recommended that batteries always be installed to
ensure continuous operation (and retain records) in case of a power outage.
1
Install or Replace Batteries
(Optional)
1. Slide off the battery
compartment cover.
2. Insert 6 x AA alkaline batteries
into the battery compartment,
as shown. Follow the polarity
(+/-) diagram in the battery
compartment.
3. Replace the battery cover.
2
Plug Power Adapter into Electric
Outlet
Write Down
3
MAC ADDRESS
12-digit number
A-B-C Switch
4
set to match
sensor
A B C
2
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to
be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of
used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries
in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT
recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
3
Write Down the MAC ADDRESS
12-digit unique ID needed for
online connectivity functions.
4
Set the A-B-C Switch
Locate the A-B-C switch inside the
battery compartment. Set the
A-B-C switch to A, B or C. You
must select the same letter choices
for both the display unit and the
sensor in order for the units to
synchronize.
MAC ADDRESS
Install Batteries
1
6 AA batteries
(Optional)
Momentary
backlight during
battery power.
Backlight can
always remain
LIGHT
on (or off) when
Plug in
power adapter
Power
is plugged in.
Adapter
8
Troubleshooting
Problem
• Confirm the status readout in PC Connect software
on your PC indicates that data was uploaded OK.
• Make certain you created an account or logged
into your existing account on www.acu-link.com,
and that you have setup your display unit MAC
ADDRESS online, as well.
• Check that the USB cable is securely connected to
the display unit AND to your PC USB port.
• Make certain the display unit is powered on.
• Make certain the PC your display unit is
connected to is always powered on.
Cannot access data
• Make certain the PC your display unit is
online or on the
connected to is always connected to the internet.
• Confirm the display unit USB mode is 3 or 4.
AcuRite mobile app
• Confirm your display unit MAC ADDRESS is
entered into the "UPLOAD" window correctly in
the PC Connect Software on your PC.
• Confirm that the "ENABLE" box is checked in the
"UPLOAD" window in the PC Connect Software
on your PC.
• Confirm your display unitʼs MAC ADDRESS is
correct in your account at www.acu-link.com and
on the AcuRite mobile app.
• Restart the PC Connect Software.
• Restart your PC.
• Check that the USB cable is securely connected to
the display unit AND to your PC USB port.
• Confirm that the correct USB mode is selected on
your display unit.
PC Connect software
• Restart the PC Connect Software.
data is different than
• Unplug the USB cable from your PC for about 1
display unit data
minute, re-insert.
• USB port may be malfunctioning, try another USB
port.
• USB cable may be malfunctioning, try another
USB cable.
If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
(877) 221-1252 for assistance.
Possible Solution
21
Advertisement
Table of Contents
