1. Manuals
  2. Brands
  3. DFI Manuals
  4. Motherboard
  5. 865PE-ALE
  6. User manual

DFI 865PE-ALE User Manual

Hide thumbs Also See for 865PE-ALE:
Table of Contents

Advertisement

Quick Links

Download this manual
865PE-ALE Rev. B
System Board
User's Manual
83400438

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 865PE-ALE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for DFI 865PE-ALE

Summary of Contents for DFI 865PE-ALE

  • Page 1 865PE-ALE Rev. B System Board User’s Manual 83400438...
  • Page 2 Copyright This publication contains information that is protected by copyright. No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior written permission from the copyright holders. This publication is provided for informational purposes only. The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any...

  • Page 3: Fcc And Doc Statement On Class B

    Battery: • Danger of explosion if battery incorrectly replaced. • Replace only with the same or equivalent type recommend by the manufacturer. • Dispose of used batteries according to the batter y manufacturer’s instructions. FCC and DOC Statement on Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.

  • Page 4: About This Manual

    About this Manual This user’s manual contains detailed information about the system board. If, in some cases, some information doesn’t match those shown in the multilingual manual, the multilingual manual should al- ways be regarded as the most updated version. The multilingual manual is included in the system board package.

  • Page 5: Table Of Contents

    Table of Contents Chapter 1 - Introduction 1.1 Specifications........................1.2 Special Features of the System Board............. 1.3 Package Checklist......................Chapter 2 - Hardware Installation System Board Layout ................... System Memory......................CPU............................Jumper Settings......................Rear Panel I/O Ports....................I/O Connectors......................Chapter 3 - Award BIOS Setup Utility 3.1 The Basic Input/Output System..............
  • Page 6 Introduction Appendix A - Enabling the Hyper-Threading Technology A.1 Enabling the Hyper-Threading Technology........... Appendix B - System Error Messages B.1 POST Beep........................B.2 Error Messages......................Appendix C - Troubleshooting C.1 Troubleshooting Checklist.................

  • Page 7: Chapter 1 - Introduction

    Introduction Chapter 1 - Introduction 1.1 Specifications Processor ® ® • Intel Pentium 4 (Prescott and Northwood) processor up to 3.4GHz+ Intel Hyper-Threading Technology FSB: 533MHz and 800MHz ® ® • Intel Celeron D processor 533MHz system data bus ® ®...
  • Page 8 Introduction Energy Efficient Design • Suppor ts ACPI specification and OS Directed Power Management • Supports ACPI STR (Suspend to RAM) function • Wake-On-Events include: Wake-On-PS/2 Keyboard/Mouse Wake-On-USB Keyboard/Mouse Wake-On-Ring (external modem) Wake-On-LAN RTC timer to power-on the system • AC power failure recovery Hardware Monitor •...

  • Page 9: Mic-In

    Introduction Rear Panel I/O Ports • 1 mini-DIN-6 PS/2 mouse port • 1 mini-DIN-6 PS/2 keyboard port • 1 DB-25 parallel por t • 1 DB-9 serial port • 1 RJ45 LAN port • 4 USB 2.0 ports • Mic-in, line-out and line-in jacks I/O Connectors •...

  • Page 10: Special Features Of The System Board

    Introduction 1.2 Special Features of the System Board Hyper-Threading Technology Functionality Requirements The system board supports Intel processors with Hyper-Threading Technology. Enabling the functionality of Hyper-Threading Technology for your computer system requires ALL of the following platforms. Components: ® ® •...
  • Page 11 Introduction S/PDIF S/PDIF is a standard audio file transfer format that transfers digital audio signals to a device without having to be converted first to an analog format. This prevents the quality of the audio signal from degrading whenever it is converted to analog. S/PDIF is usually found on digital audio equipment such as a DAT machine or audio processing device.
  • Page 12 Introduction Dual Function Power Button Depending on the setting in the “Soft-Off By PWR-BTTN” field of the Power Management Setup, this switch will allow the system to enter the Soft-Off or Suspend mode. Wake-On-Ring This feature allows the system that is in the Suspend mode or Soft Power Off mode to wake-up/power-on to respond to calls coming from an external modem or respond to calls from a modem PCI card that uses the PCI PME (Power Management Event) signal to...
  • Page 13 Introduction Wake-On-USB Keyboard/Mouse This function allows you to use a USB keyboard or USB mouse to wake up a system from the S3 (STR - Suspend To RAM) state. Important: • If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the 5VSB power source of your power supply must support ≥...

  • Page 14: Package Checklist

    Introduction AC Power Failure Recovery When power returns after an AC power failure, you may choose to either power-on the system manually, let the system power-on automatically or return to the state where you left off before power failure occurs. 1.3 Package Checklist One system board One IDE cable...

  • Page 15: Chapter 2 - Hardware Installation

    Hardware Installation Chapter 2 - Hardware Installation 2.1 System Board Layout CPU fan Mouse PS/2 power select (JP6) COM 1 DDR 1 DDR 2 ATX power USB 1 USB 2 +12V power IDE 2 IDE 1 USB 3 USB 4 USB 1-4 power select (JP3)

  • Page 16: System Memory

    Hardware Installation Warning: Electrostatic discharge (ESD) can damage your system board, processor, disk drives, add-in boards, and other components. Perform the upgrade instruction procedures described at an ESD workstation only. If such a station is not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the system chassis.

  • Page 17: Hardware Installation

    Hardware Installation Virtual Single Channel (VSC) If both channels are populated with different memory configura- tions, the MCH defaults to Virtual Single Channel. Dual Channel (DC) Dual channel provides better system performance because it doubles the data transfer rate. Only one socket is populated with Single Channel DIMM.

  • Page 18: Installing The Dim Module

    Hardware Installation 2.2.1 Installing the DIM Module A DIM module simply snaps into a DIMM socket on the system board. Pin 1 of the DIM module must correspond with Pin 1 of the socket. Notch Pin 1 1. Pull the “tabs” which are at the ends of the socket to the side. 2.

  • Page 19: Cpu

    Hardware Installation 2.3 CPU 2.3.1 Overview The system board is equipped with a surface mount 478-pin CPU socket. This socket is exclusively designed for installing an Intel processor. 2.3.2 Installing the CPU 1. Locate Socket 478 on the system board. 2.
  • Page 20 Hardware Installation 3. Position the CPU above the socket then align the gold mark on the corner of the CPU (designated as pin 1) with pin 1 of the socket. Important: Handle the CPU by its edges and avoid touching the pins. Gold mark Pin 1 4.

  • Page 21: Installing The Fan And Heat Sink

    Hardware Installation 5. Once the CPU is in place, push down the lever to lock the socket. The lever should click on the side tab to indicate that the CPU is completely secured in the socket. 2.3.3 Installing the Fan and Heat Sink The CPU must be kept cool by using a CPU fan with heatsink.
  • Page 22 Hardware Installation 1. The system board comes with the retention module base already installed. Retention Retention hole hole Retention Retention hole hole Retention module base 2. Position the fan / heat sink and retention mechanism assembly on the CPU, then align and snap the retention legs’ hooks to the retention holes at the 4 corners of the retention module base.
  • Page 23 Hardware Installation 3. The retention levers at this time remains unlocked as shown in the illustration below. Retention lever Retention lever 4. Move the retention levers to their opposite directions then push them down. This will secure the fan / heat sink and retention mechanism assembly to the retention module base.

  • Page 24: Jumper Settings

    Hardware Installation 2.4 Jumper Settings 2.4.1 Clear CMOS Data 1-2 On: Normal 2-3 On: (default) Clear CMOS Data If you encounter the following, a) CMOS data becomes corrupted. b) You forgot the supervisor or user password. c) You are unable to boot-up the computer system because the processor’s ratio/clock was incorrectly set in the BIOS.
  • Page 25 Hardware Installation 4. After powering-on the system, press <Del> to enter the main menu of the BIOS. 5. Select the Frequency/Voltage Control submenu and press <Enter>. 6. Set the processor’s ratio/clock to its default setting or an appropriate frequency ratio or bus clock. Refer to the Frequency/ Voltage Control section in chapter 3 for more information.
  • Page 26 Hardware Installation 2.4.2 CPU FSB Select JP1 JP2 JP1 JP2 JP1 JP2 1-2 On 2-3 On All Off 1-2 On 1-2 On Auto* 2-3 On 2-3 On 100MHz 2-3 On All Off 133MHz All Off All Off 166MHz All Off 2-3 On 200MHz “*”...
  • Page 27 Hardware Installation 2.4.3 PS/2 Power Select 2-3 On: 5VSB 1-2 On: 5V (default) JP6 is used to select the power of the PS/2 keyboard/mouse port. Selecting 5VSB will allow you to use the PS/2 keyboard or PS/2 mouse to wake up the system. BIOS Setting Configure the PS/2 keyboard/mouse wake up function in the Power Management Setup submenu of the BIOS.

  • Page 28: Usb Power Select

    Hardware Installation 2.4.4 USB Power Select USB 1-4 (JP3) 1-2 On: 5V 2-3 On: 5VSB (default) USB 5-8 (JP4) 1-2 On: 5V 2-3 On: 5VSB (default) JP3 and JP4 are used to select the power of the USB ports. Selecting 5VSB will allow you to use the USB keyboard or USB mouse to wake up the system..

  • Page 29: Rear Panel I/O Ports

    Hardware Installation 2.5 Rear Panel I/O Ports PS/2 Parallel Mic-in Mouse USB 2 Line-out Line-in PS/2 COM 1 USB 3-4 USB 1 The rear panel I/O ports consist of the following: • PS/2 mouse port • PS/2 keyboard port • Parallel port •...
  • Page 30 Hardware Installation 2.5.1 PS/2 Mouse and PS/2 Keyboard Ports PS/2 Mouse PS/2 Keyboard The system board is equipped with an onboard PS/2 mouse (Green) and PS/2 keyboard (Purple) ports - both at location CN1 of the system board. The PS/2 mouse port uses IRQ12. If a mouse is not connected to this port, the system will reserve IRQ12 for other expansion cards.

  • Page 31: Parallel Port

    Hardware Installation 2.5.2 Parallel Port Parallel The system board has a standard parallel port (Burgundy) at location CN7 for interfacing your PC to a parallel printer. It supports SPP, ECP and EPP. Setting Function Allows normal speed operation but (Standard Parallel Port) in one direction only.

  • Page 32: Serial Ports

    Hardware Installation 2.5.3 Serial Ports COM 1 COM 2 The system board is equipped with an onboard serial port (CN4 - Teal/Turquoise) for COM 1 and a 9-pin connector at location J8 for COM 2. These ports are RS-232C asynchronous communication ports with 16C550A-compatible UARTs that can be used with modems, serial printers, remote display terminals, and other serial devices.

  • Page 33: Universal Serial Bus Ports

    Hardware Installation 2.5.4 Universal Serial Bus Ports USB 2 USB 1 USB 4 USB 3 USB 5-6 USB 7-8 Four onboard USB 2.0/1.1 ports (Black) are at locations CN5 and CN6 for USB 1-2 and USB 3-4 respectively. J10 (USB 5-6) and J11 (USB 7-8) connectors allow you to connect 4 additional USB 2.0/1.1 ports.
  • Page 34 Hardware Installation Wake-On-USB Keyboard/Mouse The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function: • BIOS Setting: “USB KB Wake-Up From S3” in the Power Management Setup submenu of the BIOS must be set to Enabled.
  • Page 35 Hardware Installation 2.5.5 RJ45 Fast-Ethernet Port RJ45 LAN The system board is equipped with an onboard RJ45 fast-ethernet LAN por t at location CN6 of the system board. It allows the system board to connect to a local area network by means of a network hub.
  • Page 36 Hardware Installation 2.5.6 Audio (Rear Panel Audio and Front Audio) Mic-in Line-out Line-in Front audio Rear Panel Audio (CN3) • Mic-in (Pink) In a 2-channel mode, this jack is used to connect an external microphone. In a 4-channel or 6-channel mode, this jack functions as rear right/left speaker out.
  • Page 37 Hardware Installation 4-channel 2-channel 6-channel Line-in Light Blue Line-in Center/Subwoofer Front R/L Lime Line-out Front R/L Rear R/L Pink Mic-in Rear R/L Front Audio The front audio connector (J5) allows you to connect to the line-out and mic-in jacks that are at the front panel of your system. Using this connector will disable the rear audio’s line-out and mic-in func- tions.

  • Page 38: I/O Connectors

    Hardware Installation 2.6 I/O Connectors 2.6.1 CD-in Internal Audio Connector Ground Ground Left audio Right audio channel channel The CD-in (J4) connector is used to receive audio from a CD-ROM drive, TV tuner or MPEG card.
  • Page 39 Hardware Installation 2.6.2 S/PDIF Connector SPDIF in SPDIF out The system board is equipped with a S/PDIF connector. One card- edge bracket, mounted with S/PDIF ports, will be provided as an option. Install the card-edge bracket to the system chassis then connect the audio cable connector to J3.

  • Page 40: Floppy Disk Drive Connector

    Hardware Installation 2.6.3 Floppy Disk Drive Connector The system board is equipped with a shrouded floppy disk drive connector that supports two standard floppy disk drives. To prevent improper floppy cable installation, the shrouded floppy disk header has a keying mechanism. The 34-pin connector on the floppy cable can be placed into the header only if pin 1 of the connector is aligned with pin 1 of the header.

  • Page 41: Serial Ata Connectors

    Hardware Installation 2.6.4 Serial ATA Connectors SATA 2 SATA 1 The system board is equipped with two Serial ATA connectors for connecting Serial ATA devices. Connect one end of the Serial ATA cable to J15 (SATA 1) or J14 (SATA 2) and the other end to your Serial ATA device.

  • Page 42: Ide Disk Drive Connector

    Hardware Installation 2.6.5 IDE Disk Drive Connector IDE 2 IDE 1 The system board is equipped with two shrouded PCI IDE headers that will interface four Enhanced IDE (Integrated Drive Electronics) disk drives. To prevent improper IDE cable installation, each shrouded PCI IDE header has a keying mechanism.
  • Page 43 Hardware Installation Note: Refer to your disk drive user’s manual for information about selecting proper drive switch settings. Adding a Second IDE Disk Drive When using two IDE drives, one must be set as the master and the other as the slave. Follow the instructions provided by the drive manufacturer for setting the jumpers and/or switches on the drives.

  • Page 44: Irda Connector

    Hardware Installation 2.6.6 IrDA Connector IRRX Ground N. C. IRTX Connect your IrDA cable to connector J6 on the system board. Note: The sequence of the pin functions on some IrDA cable may be reversed from the pin function defined on the system board. Make sure to connect the cable to the IrDA connector according to their pin functions.

  • Page 45: Cooling Fan Connectors

    Hardware Installation 2.6.7 Cooling Fan Connectors Power Ground Sense CPU fan Ground N. C. Power Chassis fan Connect the CPU fan’s cable connector to the CPU fan connector (J13) on the system board. The chassis fan connector (J17) is used to connect an additional cooling fan.

  • Page 46: Power Connectors

    Hardware Installation 2.6.8 Power Connectors 3.3V 3.3V -12V 3.3V Ground Ground PS-ON Ground Ground Ground Ground Ground PW-OK 5VSB +12V +12V Ground Ground +12V We recommend that you use a power supply that complies with the ATX12V Power Supply Design Guide Version 1.1. An ATX12V power supply has a standard 20-pin ATX main power connector and a 4-pin +12V power connector that must be inserted onto CN9 and CN8 connectors respectively.

  • Page 47: Front Panel Connectors

    Hardware Installation 2.6.9 Front Panel Connectors RESET SPEAKER HD-LED PWR-LED ATX-SW HD-LED: Primary/Secondary IDE LED This LED will light when the hard drive is being accessed. RESET: Reset Switch This switch allows you to reboot without having to power off the system thus prolonging the life of the power supply or system.
  • Page 48 Hardware Installation PWR-LED: Power/Standby LED When the system’s power is on, this LED will light. When the system is in the S1 (POS - Power On Suspend) or S3 (STR - Suspend To RAM) state, it will blink every second. Note: If a system did not boot-up and the Power/Standby LED did not light after it was powered-on, it may indicate that the CPU...

  • Page 49: Chapter 3 - Award Bios Setup Utility

    BIOS Setup Chapter 3 - BIOS Setup 3.1 Award BIOS Setup Utility The Basic Input/Output System (BIOS) is a program that takes care of the basic level of communication between the processor and peripherals. In addition, the BIOS also contains codes for various advanced features found in this system board.

  • Page 50: Bios Setup

    BIOS Setup 3.1.1 Standard CMOS Features Use the arrow keys to highlight “Standard CMOS Features” and press <Enter>. A screen similar to the one below will appear. The settings on the screen are for reference only. Your version may not be identical to this one.
  • Page 51 BIOS Setup 3.1.1.3 IDE Channel 0 Master, IDE Channel 0 Slave, IDE Channel 1 Master and IDE Channel 1 Slave Move the cursor to the “IDE Channel 0 Master”, “IDE Channel 0 Slave”, “IDE Channel 1 Master” or “IDE Channel 1 Slave” field, then press <Enter>.
  • Page 52 BIOS Setup Access Mode For hard drives larger than 528MB, you would typically select the LBA type. Certain operating systems require that you select CHS or Large. Please check your operating system’s manual or Help desk on which one to select. Capacity Displays the approximate capacity of the disk drive.
  • Page 53 BIOS Setup 3.1.1.4 Drive A and Drive B These fields identify the types of floppy disk drives installed. None No floppy drive is installed 360K, 5.25 in. 5-1/4 in. standard drive; 360KB capacity 1.2M, 5.25 in. 5-1/4 in. AT-type high-density drive; 1.2MB capacity 720K, 3.5 in.
  • Page 54 BIOS Setup 3.1.1.7 Base Memory Displays the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512K for systems with 512K memory installed on the motherboard or 640K for systems with 640K or more memor y installed on the motherboard.

  • Page 55: Advanced Bios Features

    BIOS Setup 3.1.2 Advanced BIOS Features The Advanced BIOS Features allows you to configure your system for basic operation. Some entries are defaults required by the system board, while others, if enabled, will improve the performance of your system or let you set some features according to your preference. The screen above list all the fields available in the Advanced BIOS Features submenu, for ease of reference in this manual.
  • Page 56 BIOS Setup 3.1.2.1 CPU Feature Move the cursor to this field and press <Enter>. The following screen will appear. The settings on the screen are for reference only. Your version may not be identical to this one. Delay Prior To Thermal This field is used to select the time that would force the CPU to a 50% duty cycle when it exceeds its maximum operating temperature therefore protecting the CPU and the system board from...
  • Page 57 BIOS Setup Limit CPUID MaxVal The CPUID instruction of some newer CPUs will return a value greater than 3. The default is Disabled because this problem does not exist in the Windows series operating systems. If you are using an operating system other than Windows, this problem may occur. To avoid this problem, enable this field to limit the return value to 3 or lesser than 3.
  • Page 58 BIOS Setup 3.1.2.3 Virus Warning This field protects the boot sector and partition table of your hard disk drive. When this field is enabled, the Award BIOS will monitor the boot sector and partition table of the hard disk drive. If an attempt is made to write to the boot sector or partition table of the hard disk drive, the BIOS will halt the system and an error message will appear.
  • Page 59 BIOS Setup 3.1.2.8 None BBS SCSI Card Boot If you are using a non-BBS (BIOS Boot Specificaton) SCSI card, you must set this field to Enabled. 3.1.2.9 USB Flash Disk Type Auto Automatically detects the USB device. Emulates the USB flash disk to HDD mode. Floppy Emulates the USB flash disk to floppy mode.
  • Page 60 BIOS Setup 3.1.2.14 Gate A20 Option This entry allows you to select how gate A20 is handled. Gate A20 is a device used to address memory above 1 Mbyte. Initially, gate A20 was handled via the keyboard controller. Today, while keyboards still provide this support, it is more common, and much faster, for the system chipset to provide support for gate A20.
  • Page 61 BIOS Setup 3.1.2.18 Security Option This field determines when the system will prompt for the password - everytime the system boots or only when you enter the BIOS setup. Set the password in the Set Supervisor/User Password submenu. System The system will not boot and access to Setup will be denied unless the correct password is entered at the prompt.
  • Page 62 BIOS Setup 3.1.2.24 Full Screen Logo Show This field is applicable only if you want a particular logo to appear during system boot-up. Enabled The logo will appear in full screen during system boot- Disabled The logo will not appear during system boot-up. 3.1.2.25 Small Logo(EPA) Show Enabled The EPA logo will appear during system boot-up.

  • Page 63: Advanced Chipset Features

    BIOS Setup 3.1.3 Advanced Chipset Features The settings on the screen are for reference only. Your version may not be identical to this one. This section gives you functions to configure the system based on the specific features of the chipset. The chipset manages bus speeds and access to system memory resources.
  • Page 64 BIOS Setup Manual If you want better performance for your system other than the one “by SPD”, select “Manual” then select the best option in the “CAS Latency Time” to “DRAM RAS# Precharge” fields. 3.1.3.2 CAS Latency Time This field is used to select the local memory clock periods. 3.1.3.3 Active to Precharge Delay The options are 5, 6, 7, 8, 9 and 10.
  • Page 65 BIOS Setup 3.1.3.8 Video BIOS Cacheable As with caching the system BIOS, enabling the Video BIOS cache will allow access to video BIOS addresssed at C0000H to C7FFFH to be cached, if the cache controller is also enabled. The larger the range of the Cache RAM, the faster the video performance.
  • Page 66 BIOS Setup 3.1.3.12 Fast Chip Select The options are Auto, Enabled and Disabled. 3.1.3.13 CPC Addr/Control The options are Auto, Enabled and Disabled.

  • Page 67: Integrated Peripherals

    BIOS Setup 3.1.4 Integrated Peripherals The settings on the screen are for reference only. Your version may not be identical to this one. 3.1.4.1 OnChip IDE Device Move the cursor to this field and press <Enter>. The following screen will appear. The settings on the screen are for reference only.
  • Page 68 BIOS Setup IDE HDD Block Mode Enabled The IDE HDD uses the block mode. The system BIOS will check the hard disk drive for the maxi- mum block size the system can transfer. The block size will depend on the type of hard disk drive. Disabled The IDE HDD uses the standard mode.

  • Page 69: Sata

    BIOS Setup IDE Primary Master/Slave UDMA and IDE Secondary Master/ Slave UDMA These fields allow you to set the Ultra DMA in use. When Auto is selected, the BIOS will select the best available option after checking your hard drive or CD-ROM. Auto The BIOS will automatically detect the settings for you.
  • Page 70 BIOS Setup 3.1.4.2 Onboard Device Move the cursor to this field and press <Enter>. The following screen will appear. The settings on the screen are for reference only. Your version may not be identical to this one. USB Controller This field is used to enable or disable the onboard USB. USB 2.0 Controller If you are using a USB 2.0 device, this field must be set to Enabled.
  • Page 71 BIOS Setup BIOS Flash Protect Enabled This option will protect the system from unnecessary updating or flashing of the BIOS. When enabled, it secures the BIOS therefore any updates to the BIOS will not take effect. Disabled Disables the “BIOS flash lock” function, allowing you to update or flash the BIOS any time needed.
  • Page 72 BIOS Setup 3.1.4.3 Super IO Device Move the cursor to this field and press <Enter>. The following screen will appear. The settings on the screen are for reference only. Your version may not be identical to this one. KBC Input Clock This is used to select the input clock of your keyboard.
  • Page 73 BIOS Setup UART Mode Select This field is used to select the type of IrDA standard supported by your IrDA device. For better transmission of data, your IrDA peripheral device must be within a 30 angle and within a distance of 1 meter.
  • Page 74 BIOS Setup “EPP (Enhanced Parallel Port)” Allows bidirectional parallel port operation at maximum speed. If you selected EPP, the “EPP Mode Select” field is selectable. If you selected ECP, the “ECP Mode Use DMA” field is selectable. If you selected ECP+EPP, both “EPP Mode Select” and “ECP Mode Use DMA”...

  • Page 75: Power Management Setup

    BIOS Setup 3.1.5 Power Management Setup The Power Management Setup allows you to configure your system to most effectively save energy. The settings on the screen are for reference only. Your version may not be identical to this one. 3.1.5.1 ACPI Function This function should be enabled only in operating systems that sup- ®...
  • Page 76 BIOS Setup 3.1.5.3 Run VGABIOS if S3 Resume When this field is set to Auto, the system will initialize the VGA BIOS when it wakes up from the S3 state. This can be configured only if the “ACPI Suspend Type” field is set to “S3(STR)”. 3.1.5.4 Power Management This field allows you to select the type (or degree) of power saving by changing the length of idle time that elapses before the Suspend...
  • Page 77 BIOS Setup 3.1.5.7 Suspend Mode This is selectable only when the Power Management field is set to User Define. When the system enters the Suspend mode according to the power saving time selected, the CPU and onboard peripherals will be shut off. 3.1.5.8 HDD Power Down This is selectable only when the Power Management field is set to User Define.
  • Page 78 BIOS Setup 3.1.5.11 Power On By Ring Set this field to Enabled to use the modem ring-on function. This will allow your system to power-on to respond to calls coming from an external modem. 3.1.5.12 USB KB Wake-Up From S3 This field, when enabled, allows you to use a USB keyboard or USB mouse to wake up a system that is in the S3 (STR - Suspend To RAM) state.
  • Page 79 BIOS Setup 3.1.5.16 Keyboard/Mouse Power On This field allows you to use the PS/2 keyboard or PS/2 mouse to power-on the system. Disabled Default setting. Password When this option is selected, set the password you would like to use to power-on the system in the “KB Power On Password”...
  • Page 80 BIOS Setup 3.1.5.19 PWR Lost Resume State Keep Off When power returns after an AC power failure, the system’s power is off. You must press the Power button to power-on the system. Turn On When power returns after an AC power failure, the system will automatically power-on.
  • Page 81 BIOS Setup 3.1.6 PnP/PCI Configurations This section describes configuring the PCI bus system. It covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. The settings on the screen are for reference only. Your version may not be identical to this one.
  • Page 82 BIOS Setup 3.1.6.3 IRQ Resources Move the cursor to this field and press <Enter>. This field is used to set each system interrupt to either Reserved or PCI Device. The settings on the screen are for reference only. Your version may not be identical to this one.

  • Page 83: Pc Health Status

    BIOS Setup 3.1.7 PC Health Status The settings on the screen are for reference only. Your version may not be identical to this one. 3.1.7.1 CPU Warning Temperature This field is used to select the CPU’s temperature limit. Once the system has detected that the CPU’s temperature exceeded the limit, warning beeps will sound.
  • Page 84 BIOS Setup 3.1.7.4 Shutdown Temperature You can prevent the system from overheating by selecting a tem- perature in this field. If the system detected that its temperature exceeded the one set in this field, it will automatically shutdown. This function will work only when you enable this function in the Hardware Monitor utility.
  • Page 85 BIOS Setup 3.1.8 Frequency/Voltage Control The settings on the screen are for reference only. Your version may not be identical to this one. 3.1.8.1 CPU Clock Ratio This field is used to select the frequency ratio of the processor. Important: The frequency ratio of some processors may have been locked by the manufacturer.
  • Page 86 BIOS Setup 3.1.8.4 Async AGP/PCI Clock This field is used to select the bus clock of the AGP and PCI. 3.1.8.5 CPU Clock This field provides several options for selecting the external system bus clock of the processor. The available options allow you to adjust the processor’s bus clock by 1MHz increment.
  • Page 87 BIOS Setup 3.1.9 Load Fail-Safe Defaults The “Load Fail-Safe Defaults” option loads the troubleshooting default values permanently stored in the ROM chips. These settings are not optimal and turn off all high performance features. You should use these values only if you have hardware problems. Highlight this option in the main menu and press <Enter>.

  • Page 88: Load Optimized Defaults

    BIOS Setup 3.1.10 Load Optimized Defaults The “Load Optimized Defaults” option loads optimized settings from the BIOS ROM. Use the default values as standard values for your system. Highlight this option in the main menu and press <Enter>. Type <Y> and press <Enter> to load the Setup default values.

  • Page 89: Set Password

    BIOS Setup 3.1.11 Set Password If you want to protect your system and setup from unauthorized entry, set a password with the “System” option selected in the Advanced BIOS Features. If you want to protect access to setup only, but not your system, set a password with the “Setup” option selected in the Advanced BIOS Features.
  • Page 90 BIOS Setup 3.1.12 Save & Exit Setup When all the changes have been made, highlight “Save & Exit Setup” and press <Enter>. Type “Y” and press <Enter>. The modifications you have made will be written into the CMOS memory, and the system will reboot. You will once again see the initial diagnostics on the screen.

  • Page 91: Exit Without Saving

    BIOS Setup 3.1.13 Exit Without Saving When you do not want to save the changes you have made, highlight “Exit Without Saving” and press <Enter>. Type “Y” and press <Enter>. The system will reboot and you will once again see the initial diagnostics on the screen. If you wish to make any changes to the setup, press <Ctrl>...

  • Page 92: Updating The Bios

    BIOS Setup 3.2 Updating the BIOS To update the BIOS, you will need the new BIOS file and a flash utility, AWDFLASH.EXE. You can download them from DFI’s web site or contact technical support or your sales representative. Note: AWDFLASH.EXE works only in DOS mode.
  • Page 93 BIOS Setup 6. The following will appear. Do You Want to Save BIOS (Y/N) This question refers to the current existing BIOS in your system. We recommend that you save the current BIOS and its flash utility; just in case you need to reinstall the BIOS. To save the current BIOS, press <Y>...

  • Page 94: Chapter 4 - Supported Softwares

    Supported Software Chapter 4 - Supported Software 4.1 Drivers, Utilities and Software Applications The CD that came with the system board contains drivers, utilities and software applications required to enhance the performance of the system board. Inser t the CD into a CD-ROM drive. The autorun screen (Mainboard Utility CD) will appear.

  • Page 95: Supported Software

    Supported Software 4.1.1 Intel Chipset Software Installation Utility The Intel Chipset Software Installation Utility is used for updating  Windows 98/98SE/2000/ME/XP's INF files so that the Intel chipset can be recognized and configured properly in the system. To install the utility, please follow the steps below. 1.

  • Page 96: Audio Drivers

    Supported Software 4.1.2 Audio Drivers To install, please follow the steps below. 1. On the left side of the autorun screen, click the “AUDIO” icon. 2. Click “Audio Drivers” on the main menu. The following screen will appear. 3. Follow the prompts on the screen to complete installation. 4.
  • Page 97 Supported Software 4.1.3 Intel USB 2.0 Drivers If you are using a USB 2.0 device, you must install the USB 2.0 driver. The drivers are supported in the following operating systems:    Windows 98 SE, Windows ME and Windows 2000.
  • Page 98 Supported Software  Windows 2000 does not support auto-installation of the USB 2.0 driver. When you click “Intel USB 2.0 Drivers”, the “readme” screen will appear. 3. Follow the installation instructions shown on the screen. 4. Reboot the system for the driver to take effect. Important: ®...

  • Page 99: Lan Drivers

    Supported Software 4.2.4 LAN Drivers The LAN drivers support autorun for the following operating     systems: Windows 98, Windows 98 SE, Windows ME, Windows  2000 and Windows To install the driver, please follow the steps below. 1.

  • Page 100: Hardware Monitor

    Supported Software 4.1.5 Hardware Monitor The system board comes with the Hardware Monitor utility con- tained in the provided CD. This utility is capable of monitoring the system’s “health” conditions and allows you to manually set a range (Highest and Lowest Limit) to the items being monitored. If the settings/values are over or under the set range, a warning message will pop-up.
  • Page 101 Supported Software 4.1.6 Microsoft DirectX 9 To install, please follow the steps below. 1. On the left side of the autorun screen, click the “TOOLS” icon. 2. Click “Microsoft DirectX 9” on the main menu. The following screen will appear. 3.

  • Page 102: Installation Notes

    2. All steps or procedures to install software drivers are subject to change without notice as the softwares are occassionally updated. Please go to DFI's web site at "http://www.dfi.com/support1/ download2.asp" for the latest version of the drivers or software applications.

  • Page 103: Enabling The Hyper-Threading Technology

    Enabling Hyper-Threading Technology Appendix A - Enabling Hyper-Threading Technology A.1 Enabling Hyper-Threading Technology To enable the functionality of the Hyper-Threading Technology, please follow the requirements and steps below. Basically, the following ® ® presumes that you have already installed an Intel Pentium Processor with Hyper-Threading Technology.
  • Page 104 Enabling Hyper-Threading Technology Click the General tab. The processor shown under Computer should resemble the one shown below. Now click the Hardware tab then click Device Manager. The items shown under Computer and Processors should resemble the ones shown below.
  • Page 105 Enabling Hyper-Threading Technology Lastly, press the <Ctr l> <Alt> and <Del> keys simultaneously. The Windows Task Manager dialog box will appear. Click the Performance tab. The diagram under CPU Usage History should resemble the one shown below.

  • Page 106: Appendix B - System Error Messages

    System Error Message Appendix B - System Error Message When the BIOS encounters an error that requires the user to correct something, either a beep code will sound or a message will be displayed in a box in the middle of the screen and the message, PRESS F1 TO CONTINUE, CTRL-ALT-ESC or DEL TO ENTER SETUP, will be shown in the information box at the bottom.
  • Page 107 System Error Message setting than indicated in Setup. Determine which setting is correct, either turn off the system and change the jumper or enter Setup and change the VIDEO selection. FLOPPY DISK(S) fail (80) Unable to reset floppy subsystem. FLOPPY DISK(S) fail (40) Floppy type mismatch.

  • Page 108: Appendix C - Troubleshooting

    Troubleshooting Appendix C - Troubleshooting C.1 Troubleshooting Checklist This chapter of the manual is designed to help you with problems that you may encounter with your personal computer. To efficiently troubleshoot your system, treat each problem individually. This is to ensure an accurate diagnosis of the problem in case a problem has multiple causes.

  • Page 109: Power Supply

    Troubleshooting The picture seems to be constantly moving. 1. The monitor has lost its vertical sync. Adjust the monitor’s vertical sync. 2. Move away any objects, such as another monitor or fan, that may be creating a magnetic field around the display. 3.

  • Page 110: Hard Drive

    Troubleshooting Hard Drive Hard disk failure. 1. Make sure the correct drive type for the hard disk drive has been entered in the BIOS. 2. If the system is configured with two hard drives, make sure the bootable (first) hard drive is configured as Master and the second hard drive is configured as Slave.

  • Page 111: Serial Port

    Troubleshooting Serial Port The serial device (modem, printer) doesn’t output anything or is outputting garbled characters. 1. Make sure that the serial device’s power is turned on and that the device is on-line. 2. Verify that the device is plugged into the correct serial port on the rear of the computer.

Table of Contents