Table of Contents
Advertisement
Using handy features
I Using auto positioning (Auto Positioning)
This function sets up the projector to the optimum state for
each type of the input signal by using simple operations.
1
Press the AUTO POSITION button.
The Auto positioning menu appears.
2
Press the AUTO POSITION button again.
The menu item is automatically adjusted/positioned.
For computer input, the
icon will appear during
processing.
Note
• Auto adjustment/positioning may not be performed correctly for source signals other
than those supported by the projector
G Manual adjustment and positioning
The menu items vary depending on the source type, as shown in the table below.
Use the
buttons to adjust the items in the table below, then press
the
button when you are finished. The menu disappears. (The EXPAND OFF
button on the remote control also allows you to exit the menu mode.)
Source
Item
Computer
Phase
Adjust with
Frequency
Adjust with
flickering when many vertical lines appear on the screen.
H-position
Move left
V-position
Move down
Clamp 1
Adjusts the clamp pulse position with
Clamp 2
Adjusts the clamp pulse width with
Y/P
/P
Phase
Adjust with
B
R
Signal format [
of the following]
480i(525i)@60Hz/480p(525p)@60Hz/
576i(625i)@50Hz/576p(625p)@50Hz/
720p(750p)@60Hz/720p(750p)@50Hz/
1080i(1125i)@60Hz/1080i(1125i)@50Hz/
1035i(1125i)@60Hz/1152i(1250i)@50Hz
Video
Video mode
[
S-video
of the followings]
NTSC/PAL/SECAM/PAL-N/PAL-M/PAL60/NTSC4.43
Note
• Moving pictures generated with the DVD software for computers may appear
unnatural if it is projected with this projector, but it is not a malfunction.
Remote
Control panel
Control
FAN TEMP LAMP POWER
SOURCE
ON / STANDBY
+
ZOOM.
MENU/ENTER
-
+
VOL.
VOL.
KEYSTONE
AUTO POSITION
-
ZOOM.
p.38
,
p.39
.
Description
to eliminate flicker.
to eliminate periodic patterns and
Move right
Move up
or
or
to eliminate flicker.
: Enter to setting mode]
[
: Select one
[Apply:
]
: Enter to setting mode]
[
: Select one
[Apply:
]
24
I Correcting the keystone distortion (Keystone)
When the foot adjuster
projection angle, the picture will undergo keystone (trap-
ezoidal) distortion.
This projector is capable of correcting this keystone distortion.
1
Press the KEYSTONE button.
The Keystone menu appears.
2
Use the
On completing the adjustment, press the
EXPAND OFF button on the remote control for menu dismissal).
Item
Keystone
Notes
• Depending on the amount of keystone adjustment and the content of images, some
information may be lost, or the picture quality may suffer.
• Keystone adjustment will not change the shape of the menus.
I Zooming out the images
This equipment is provided with the digital zoom (electric zoom: 100-80%). (Note that
the display, if digitally zoomed out, may suffer from some degradation.)
.
1
Press the ZOOM – button.
.
Each time the ZOOM – button is pressed, the
image is reduced in size.
2
Press the ZOOM + button to bring it back
to the original size.
Each time the ZOOM + button is pressed, the
image size increases.
(You cannot make it larger than the original size.)
p.23
is used to change the
Control panel
Before correction After correction
VOL.
buttons for keystone adjustment.
button to dismiss the menu (you can also use the
Description
Shrink bottom of the screen
Control panel
VOL.
• Pressing either the ZOOM-
• The adjustment value will
25
Remote
Control
FAN TEMP LAMP POWER
SOURCE
ON / STANDBY
ZOOM.
+
MENU/ENTER
-
VOL.
+
KEYSTONE
AUTO POSITION
ZOOM.
-
Shrink top of the screen
Remote
Control
FAN TEMP LAMP POWER
SOURCE
ON / STANDBY
ZOOM.
+
MENU/ENTER
-
VOL.
+
KEYSTONE
AUTO POSITION
ZOOM.
-
Notes
or ZOOM+ button would
display the
icon.
automatically be saved.
Advertisement
Table of Contents
