Table of Contents
Advertisement
IMPORTANT SAFEGUARDS (Continued)
Place of installation
For safety's sake, do not use the projector at any place subjected to high temperature and
high humidity. Please maintain an operating temperature, humidity, and altitude as
specified below.
• Operating temperature: between +32 F (0 C) and +95 F (+35 C)
• Operating humidity: between 30% and 70%
• Never put any heat-producing device under the projector to prevent the projector from
being overheated.
• Do not install the projector at a place that is unstable or subject to vibration.
• Do not install the projector near any equipment that produces a strong magnetic field.
Also refrain from installing the projector near any cable carrying a large amount of
current.
• Place the projector on a solid, vibration-free surface. Otherwise it may fall, causing
serious injury or damage.
• Do not stand the projector on its end. It may fall, causing serious injury or damage.
• Slanting the projector more than 10˚(right and left) or 20˚(front and rear) may cause
trouble or explosion of the lamp.
• Do not place the projector near air-conditioning unit or heater to avoid the air outlet and
inlet grilles from being exposed to hot air.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user's
authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
6
ABOUT LAMP
The lamp is designed to project the image on the LCD panels. When the lamp no longer
functions, replace it with a new one.
Caution:
• Do not remove the lamp immediately after using the projector. You may get burned
because the lamp is very hot after use.
• Before replacing the lamp, press the POWER button to turn off the lamp and wait for
two minutes for the lamp and LCD panels to cool down. Unplug the power cord from the
wall outlet and wait one hour for the lamp to cool down completely.
• Do not remove the lamp except for replacement. Careless handling can cause injury or
fire.
• Do not touch the lamp directly. It may break and cause injury or burn.
• Be sure not to drop the lamp lid screw into the projector. Also be sure not to put metal or
any flammable objects inside because it may cause fire or electric shock. If any objects
should fall inside, unplug and contact your dealer.
• Install the lamp securely to prevent failure and fire.
• If the lamp should break, small glass fragments may fall out through the grilles and
some may remain inside of the projector or the lamp box. When taking the lamp box
out, be sure to turn over the projector and hold the handle of the lamp box to avoid
injury due to the glass fragments.
• If the lamp should break, never shake the lamp box or hold it in front of your face after
removing it. The glass fragments may fall out and cause injury to your eyes.
• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
• The replacement span of the lamp depends on the environment. For replacement
lamps, please contact your dealer.
• This projector uses a lamp that contains mercury. Disposal of the lamp or the projector
with the lamp may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries
Alliance: www.eiae.org. (For US only).
ABOUT REMOTE BATTERIES
Caution:
• Use of a battery of wrong type may cause explosion.
• Dispose of used batteries according to the instructions. Batteries may explode if
misused. Do not recharge, disassemble, or dispose of in fire.
• Be sure to handle the battery according to the instructions.
• Load the battery with its positive (+) and negative (-) sides correctly oriented as
indicated on the remote control.
• Keep batteries out of reach of children and pets.
• Remove the battery, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• Do not try to recharge batteries. Do not use rechargeable batteries.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If
the solution comes in contact with your eyes, rinse them with water and then consult
your doctor.
7
Advertisement
Table of Contents
