SCANMASKIN Scan Combiflex 800 User Manual
  1. Manuals
  2. Brands
  3. SCANMASKIN Manuals
  4. Grinder
  5. Scan Combiflex 800
  6. User manual

SCANMASKIN Scan Combiflex 800 User Manual

Grinding machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Scan Combiflex 800
Users Guide
http://www.scanmaskin.com

Advertisement

Table of Contents
loading

Related Manuals for SCANMASKIN Scan Combiflex 800

Summary of Contents for SCANMASKIN Scan Combiflex 800

  • Page 1 Scan Combiflex 800 Users Guide http://www.scanmaskin.com...
  • Page 2 Scan Combiflex 800 – Manual Dear Customer! Thank you for choosing Scanmaskin as your supplier. We wish you all the best with your new Scan Combiflex™ 800 and hope that it lives up to your expectations. Scanmaskin Sverige AB Claes-Göran Bergstrand...
  • Page 3 800” hereby referred to as “SC-800”. SC-800 may only be used for grinding horizontal surfaces approved by Scanmaskin Sweden AB. If SC-800 is used for other purposes or handled in ways other than that described in this User Guide, Scanmaskin Sweden AB disclaims all responsibility. Especially note the section “...

  • Page 4: Table Of Contents

    Scan Combiflex 800 – Manual Table of Contents Specifications ............................2 Electrical specifications ....................... 2 Mechanical specifications ......................3 1.2.1 Water connection ........................3 Tools ............................. 4 Range of application ........................5 Scope of supply ..........................5 Overview ............................6 Safety Regulations ..........................
  • Page 5 Scan Combiflex 800 – Manual 5.6.1 Common faults ........................20 5.6.2 Error codes .......................... 21 Spare Parts ............................22 Warranty ............................26 EU Declaration ..........................27 Alphabetical reference ........................28 10 Contact information .......................... 30 - v -...

  • Page 6: Specifications

    Scan Combiflex 800 – Manual Chapter -1 1 Specifications The SC-800 is available with different power inputs and some options regarding wet grinding. This is described in the different sections later on in this chapter. 1.1 Electrical specifications To find the specifications that apply to your machine, check the information plate on the electrical cabinet door.

  • Page 7: Mechanical Specifications

    Scan Combiflex 800 – Manual Chapter -1 1.2 Mechanical specifications Model SC-800 800 mm (32”) Grinding diameter Grinding plate diameter 240 mm (9.5”) 500 – 1400 RPM Grinding plate speed Mass 400 kg (880 lbs) Synchronized Gear barrel Table 1-2...

  • Page 8: Tools

    Chapter -1 Figure 1-1 Standard SC-800 1.3 Tools The machine must be equipped with tools approved by Scanmaskin Sweden AB before operation. See “Grinding guide” for information about available tools and “4.11Changing tools” for information about how to change the tools.

  • Page 9: Range Of Application

    Scan Combiflex 800 – Manual Chapter -1 1.4 Range of application SC800 is exclusively designed to process horizontal surfaces. SC800 must not be used for other purposes than stated in this user guide. The manufacturer will not be liable for damage or injury resulting from incorrect usage of SC800.

  • Page 10: Overview

    Scan Combiflex 800 – Manual Chapter -1 1.6 Overview Figure 1-3 Overview of SC-800 Item Description Reference Control panel 4.3Control panel Handle Power inlet 1.1Electrical specifications Dust collector connection System fan Wheel Grinding head 4.11Changing tools Dust cover Cover Bolt...

  • Page 11: Safety Regulations

    Scan Combiflex 800 – Manual Chapter 0 2 Safety Regulations Read this entire chapter carefully! Failure to comply with safety regulations may result in serious injuries or damages. 2.1 Legend Notation regarding safety Notation regarding electrical safety Notation regarding safety during transport...

  • Page 12: Organizational Measures

    Scan Combiflex 800 – Manual Chapter 0 2.3 Organizational measures The user guide is to be kept near the location where the machine is being operated and must be within reach at all times. In addition to this user guide general and legal regulations regarding accident prevention and environmental protection must be complied with as per local regulations.

  • Page 13: Personnel Selection And Qualification

    To perform maintenance work correctly it is imperative to be equipped with the proper tools for the task in question. Repairs may only be made by Scanmaskin Sweden AB certified service technicians. Some grinding work may generate sparks under certain circumstances. Personnel working with the machine must therefore be aware of the risk of fire and how to handle a fire situation properly.

  • Page 14: Electrical Safety

    Scan Combiflex 800 – Manual Chapter 0 Secure the work area around the machine in public areas providing a safety distance of at least 10 m (3.3 ft) from the machine. Faults must be immediately rectified. Carry out the switch on, and switch off operations in accordance with this user guide.

  • Page 15: Cables

    Scan Combiflex 800 – Manual Chapter 0 The work area must be secured against any third party entering the work area. Follow local electrical engineering regulations while working on the machine. Never leave a machine unattended. Use only tools that are insulated against electricity.

  • Page 16: Safety Regarding Maintenance

    Scan Combiflex 800 – Manual Chapter 0 2.8 Safety regarding maintenance Set the machine into the Safety off position before beginning any work on the machine. See “2.7Definition of the “Safety off position””. Never work on the machine while power is still connected! All parts must have come to a complete stop before beginning any work! When the machine is lying down on its back it might tilt to it’s upwards position.

  • Page 17: Lifting

    Scan Combiflex 800 – Manual Chapter 0 2.9.2 Lifting The machine must be secured according to local safety regulations before lifted. No person is allowed beneath a lifted machine! The machine must be lifted according to the instructions in “3.3Lifting”Observe the machines point of balance before lifting! Failure to comply with these regulations may cause injuries or damages.

  • Page 18: Transport

    Scan Combiflex 800 – Manual Chapter 1 3 Transport 3.1 Precautions Read “2.9Safety regarding transport” before attempting to transport the machine. 3.2 Manual transport  Detach the tools according to the instructions in “4.11Changing tools”.  Push the handle downwards to lift the gear barrel about 10 cm (4”) from the ground.

  • Page 19: Operation

    Scan Combiflex 800 – Manual Chapter 2 4 Operation 4.1 Precautions Any machine, if it is not used according the regulations, may be hazardous for operating, setting-up and service personnel. The operating authority is responsible for compliance with the safety regulations during operation and maintenance, and for the use of safety devices supplied with the machine, as well as the provision of appropriate additional safety devices! Never operate the machine without proper tools.

  • Page 20: Control Panel

    Scan Combiflex 800 – Manual Chapter 2 4.3 Control panel Figure 4-2 Control panel of SC-800. Item Text Description Selects rotation direction HOURS Hour meter EMERGENCY STOP Emergency stop START Starts the machine STOP Stops the machine SPEED Speed of rotation Table 4-1 Description of the control panel.

  • Page 21: Start Up

    Scan Combiflex 800 – Manual Chapter 2 4.5 Start up See ”4.1Precautions” before starting the machine. How to start the machine  Make sure that the power plug and hoses for dust collector and water (if used) are connected to the machine.

  • Page 22: Using With Generator

    Scan Combiflex 800 – Manual Chapter 2 This illustration shows how to change the Scan-On tools. Figure 4-3 How to fit the diamond segments on the Scan-On plate Insert the segment at the widest part of the slot Push the segment outwards...

  • Page 23: Maintenance

    Scan Combiflex 800 – Manual Chapter 3 5 Maintenance 5.1 Precautions Set the machine into the Safety off position before beginning any work on the machine. See “2.7Definition of the “Safety off position””. Read “2.6Electrical safety” before beginning any maintenance work.

  • Page 24: Cleaning The Machine

    Scan Combiflex 800 – Manual Chapter 3  Make sure the machine is in its “Safety off position”  Tilt the machine backwards and secure it.  Remove any tools used.  Loosen the three screws holding the Scan-On plate.

  • Page 25: Error Codes

    Scan Combiflex 800 – Manual Chapter 3 5.6.2 Error codes Code Description Cause Correction  One of the three phases is missing from the  Inspect the fuses in the worksites fuse box A2001 Over current  Inspect cables power supply ...

  • Page 26: Spare Parts

    Scan Combiflex 800 – Manual Chapter 4 6 Spare Parts - 22 -...
  • Page 27 Scan Combiflex 800 – Manual Chapter 4 No. Part Control panel Handle Frame Water inlet (optional) Power inlet O ring Electrical cabinet Fan grid Wheel Bolt Washer Wheel axis Cover Handleaxis Handle lock pin Interna dusthose Rubber seal Left dust hose...
  • Page 28 Scan Combiflex 800 – Manual Chapter 4 6.1 Grinding head - 24 -...

  • Page 29: Electrical Schematics

    Scan Combiflex 800 – Manual Chapter 4 6.1.1 Electrical schematics Panel Hour Meter Speed Emergency Stop Stop Start 8 8 8 8 8 h 11 10 Inverter and fans Connectors + (Red) - (Black) Internal External Cable description + (Red)

  • Page 30: Warranty

    This product from Scanmaskin Sweden AB comes with a twelve month warranty. If the product does not function satisfactorily during this period, Scanmaskin will return the product to full working order for normal use which the product is intended for – with no charge for labour or spare parts, according to the following conditions: The warranty only applies to persons that have legal right to the equipment during the warranty period.

  • Page 31: Eu Declaration

    Scan Combiflex 800 – Manual Chapter 6 8 EU Declaration Declaration of conformity CE Scanmaskin Sweden AB Manufacturer Address Heljesvägen 10 437 36Lindome Sweden Product Grinding machine Name Scan Combiflex 800 Serialnumber _________ Standards used including number Machine directives 2006/42/EG...

  • Page 32: Alphabetical Reference

    Scan Combiflex 800 – Manual Chapter 7 9 Alphabetical reference Application range of ....................................5 typical ..................................... 5 Cleaning ....................................20 Contact information................................... 30 Control panel ..................................... 16 Electrical schematics ................................25 Error codes ....................................21 EU Declaration ..................................27 Faults troubleshooting ..............................
  • Page 33 Scan Combiflex 800 – Manual Chapter 7 Transport ....................................14 lifting ....................................14 manual ....................................14 Warranty ....................................26 - 29 -...

  • Page 34: Contact Information

    Scan Combiflex 800 – Manual Chapter 8 10 Contact information Sweden (Head Office) Heljesvägen 10 Box 187 SE-437 22 Lindome Phone: +46 (0) 31 99 49 70 Fax: +46 (0) 31 99 48 70 E-mail: info@scanmaskin.se Website: www.scanmaskin.se Denmark Torvegade 22...

Table of Contents