Related Manuals for LifeFitness FIT SERIES
Summary of Contents for LifeFitness FIT SERIES
-
Page 1: Assembly Instructions
FIT SERIES LEG PRESS/CALF ASSEMBLY INSTRUCTIONS Part # 7488901 Revision:5/06/03 Rev A. -
Page 2: Parts List
PARTS LIST DESCRIPTION PART # DESCRIPTION PART # TOWER ACU04-1641 ACUDA1C03804316NU 3/8 X 43mm BOLT LEG PRESS FRAME ACU04-1636 ACUDA1C03805016NU 3/8 X 50mm BOLT HANDLE ACU04-1378 ACUDA1C03806716NU 3/8 X 67mm BOLT MAIN PIVOT ARM ACU04-1379 3/8 X 73mm BOLT ACUDA1C03807316NU SECONDARY PIVOT ARM ACU04-1380 3/8 X 90mm BOLT... - Page 3 25 3/8 X 43mm BOLT 3/8” LOW HEIGHT LOCK 26 3/8 X 50mm BOLT 3/8” SAE WASHER 27 3/8 X 67mm BOLT 28 3/8 X 73mm BOLT 3/8” BLACK FLAT WASHER 29 3/8 X 90mm BOLT RH CAP (WHITE/PLATINUM/BLACK) 3/8 X 1/2” FLANGE SPACER WASHER 3/8 X 1-1/2”...
- Page 4 30 3/8 X117mm BOLT 31 3/8 X 25mm BUTTON HEAD BOLT 32 3/8 X 90mm BUTTON HEAD BOLT 47 5/16 X1/2” SHOULDER BOLT 3/8 X 3/8” SPACER Bolt Length Ruler NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH...
- Page 5 27 3/8 X 67mm 29 3/8 X 90mm 27 3/8 X 67mm 3/8 X 117mm 30 FIGURE 1 STEP 1: • LOOSELY assemble the BASE (7) to the LEG PRESS FRAME (2) and TOWER (1) using eight RH CAPS (38), two 3/8 X 117mm BOLTS (30), two 3/8 X 90mm BOLTS (29), eight 3/8”...
- Page 6 TIGHTEN! TIGHTEN! FIGURE 2 STEP 2: • Pull up the SPRING PIN on the LEG PRESS FRAME (2) and insert the BACK PAD ADJUST (46). Assemble one 5/16 X 1/2” SHOULDER BOLT (47) to the BACK PAD ADJUST (46) as shown in FIGURE 2. •...
- Page 7 1” 13” FIGURE 4 3/8 X 117mm 30 STEP 4: • Assemble four 3/4 X 4” PIVOT SHAFTS (15) to the MAIN & SECONDARY PIVOT ARMS (4 & 5) as shown in FIGURE 4. • SECURELY assemble the MAIN & SECONDARY PIVOT ARMS (4 & 5) to the LEG PRESS FRAME (2) using four RH CAPS (38), two 3/8 X 117mm BOLTS (30), four 3/8”...
- Page 8 28 3/8 X 73mm BLACK FIGURE 6 STEP 6: • SECURELY assemble the BACK PAD (12) to the BACK PAD ADJUST (46) using two BLACK RH CAPS (37), two 3/8 X 73mm BOLTS (28), two 3/8” SAE WASHERS (35) and two 3/8” RH WASHERS (36) as shown in FIGURE 6. 28 3/8 X 73mm FIGURE 7 STEP 7:...
- Page 9 25 3/8 X 43mm 27 3/8 X 67mm FIGURE 8 STEP 8: • Route the WEIGHT STACK CABLE (13) through the TOWER (1) as shown, and SECURELY assemble one 4-1/2” PULLEY (16) inside the TOWER (1) using one 3/8 X 67mm BOLT (27), two 3/8 X 1/2” FLANGE SPACERS (23) and one 3/8” LOW HEIGHT LOCK NUT (34) as shown in FIGURE 8.
- Page 10 LUBRICATION NOTE: When finished assembling the Weight Stack, open the lube Pack provided with this unit and apply a thin film of Lubricant around the first 2 to 3 inches of each Guide Rod above the Head Plate Assembly. After the cables are installed, use of the ma- chine will spread the lubricant over the length of the Guide Rods and into the...
- Page 11 27 3/8 X 67mm TIGHTEN! FIGURE 10 STEP 10: • Route the threaded end of the WEIGHT STACK CABLE (13) through the GUIDE ROD SUPPORT (10) and SECURELY assemble the GUIDE ROD SUPPORT (10) to the TOWER (1) using two 3/8 X 67mm BOLTS (27), four 3/8” FLAT WASHERS (44) and two 3/8” LOW HEIGHT LOCK NUTS (34) as shown in FIGURE 10.
- Page 12 25 3/8 X 43mm 25 3/8 X 43mm FIGURE 11 STEP 11: • Route the WEIGHT STACK CABLE (13) around one 4-1/2” PULLEY (16) and SECURELY assemble the 4-1/2” PULLEY (16) to the FLOATING PULLEY BRACKET (9) using two 3/8 X 43mm BOLTS (25), four RH CAPS (38), four 3/8” SAE WASHERS (35), four 3/8” RH WASHERS (36), and two 3/8”...
- Page 13 26 3/8 X 50mm FIGURE 12 27 3/8 X 67mm STEP 12: • Route the LEG PRESS CABLE (14) through the MAIN PIVOT ARM (4) as shown, and SECURELY assemble one 4-1/2” PULLEY (16) to the MAIN PIVOT ARM (4) using two RH CAPS (38), one 3/8 X 67mm BOLT (27), two 3/8 X 1/2” FLANGE SPACERS (23), two 3/8” SAE WASHERS (35), two 3/8”...
- Page 14 3/8 X 43mm 25 25 3/8 X 43mm FIGURE 14 STEP 14: • Route the LEG PRESS CABLE (14) through the horizontal bracket on the LEG PRESS FRAME (2) and SECURELY assemble one 4-1/ 2” PULLEY (16) to the bracket using two RH CAPS (38), two 3/8 X 43mm BOLTS (25), two 3/8” SAE WASHERS (35) and two 3/8” RH WASHERS (36) as shown in FIGURE 14.
- Page 15 ADJUSTMENT ADJUSTMENT FIGURE 15 STEP 15: • LOOSELY thread end of the LEG PRESS CABLE (14) into the end of the stem on the FLOATING PULLEY BRACKET (9). See FIGURE 15. • Adjustments can be made in the above locations to set the correct amount of tension in the cables. •...
- Page 16 HEAD BOLTS (32), twenty-four 3/8” BLACK FLAT WASHERS (33) and twelve 3/8” ACORN NUTS (43) as shown above. Thank you for purchasing the LifeFitness FIT SERIES LEG PRESS/CALF. If unsure of proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at...
-
Page 17: Warranty Information
• Upholstery with mild soap and water. • Guide rods with a cotton cloth. • Hand grips with mild soap and water. • Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at (800) 351-3737 Inspect: •...