Related Manuals for Evolution RAGE 2
Summary of Contents for Evolution RAGE 2
- Page 1 Original Instructions Written in UK English Date Published: 04 / 10 / 2013...
- Page 3 ENGLISH Original Instructions...
-
Page 4: Table Of Contents
www.evolutionpowertools.com TABLE OF CONTENTS English Page 4 Español Página 22 Français Page 44 INTrOduCTION Guarantee Page 5 Machine Specification Page 6 Labels and Symbols Page 7 Vibration Page 8 Intended use of this Power Tool Page 8 Prohibited use of this Power Tool Page 8 SAFETY PrECAuTIONS Electrical Safety... -
Page 5: Guarantee
In no event shall you to validate your machine’s guarantee period via Evolutions website by entering your Evolution Power Tools be liable for loss or details and thus ensure prompt service if ever damage resulting directly or indirectly from the use of our merchandise or from any other needed. -
Page 6: Machine Specification
www.evolutionpowertools.com SPECIFICATIONS CuTTING CAPACITY METrIC IMPErIAL Mild Steel Plate (Optimal Cutting Thickness) 1/4” Square Tube at 90° (Mild Steel) 120 x 120mm 4-3/4 x 4-3/4” Square Tube at 45° (Mild Steel) 89 x 89mm 3-1/2 x 3-1/2” Rectangle Tube at 90° (Mild Steel) 95 x 180mm 3-3/4 x 7-1/8”... -
Page 7: Labels And Symbols
Do not operate this machine medical advice. if warning and/or instruction labels are • The measurement and assessment of human missing or damaged. Contact Evolution exposure to hand-transmitted vibration in the Power Tools for replacement labels. workplace is given in: BS EN ISO 5349-1:2001 Note: All or some of the following symbols and BS EN ISO 5349-2:2002. -
Page 8: Intended Use Of This Power Tool
This product is a Hand Operated Chop Saw and has been designed to be Volts used with special Evolution blades. Only use accessories designed for use in this machine and/or those recommended specifically Amperes by Evolution Power Tools Ltd. -
Page 9: Electrical Safety
www.evolutionpowertools.com (1.14) ELECTrICAL SAFETY (2.2) 1) General Power Tool Safety warnings [work area safety] This machine is fitted with the correct moulded plug and mains lead for the designated market. If the supply cord is a) Keep work area clean and well lit. damaged, it must be replaced by a special Cluttered or dark areas invite accidents. - Page 10 www.evolutionpowertools.com (2.4) 3) General Power Tool Safety (2.5) 4) General Power Tool Safety warnings [Personal Safety]. warnings [Power tool use and care]. a) Do not force the power tool. Use the a) Stay alert, watch what you are doing and use common sense when operating a power correct power tool for your application.
-
Page 11: Additional Safety Instructions
www.evolutionpowertools.com (2.6) 5) General Power Tool (2.8) wArNING: the operation of any power Safety warnings [Service] tool can result in foreign objects being thrown towards your eyes, which could result in a) Have your power tool serviced by a severe eye damage. Before beginning power qualified repair person using only identical tool operation, always wear safety goggles replacement parts. - Page 12 www.evolutionpowertools.com i) Do not use High Speed b) If the blades are binding, or when Steel (HSS) saw blades. interrupting a cut for any reason, release j) Inspect the machine and the blade the trigger and hold the saw motionless before each use.
-
Page 13: Getting Started Unpacking
(3.4) wArNING: If any parts are missing, do with this machine the following accessories not operate your machine until the missing are also available from the Evolution online parts are replaced. Failure to follow this rule shop at www.evolutionpowertools.com could result in serious personal injury. -
Page 14: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW A parts diagram can be downloaded from www.evolutionpowertools.com. 1. Lower Blade Guard 2. Front Swiveling Vice Jaw 3. Repositionable Rear Vice Jaw 4. Upper Blade Guard 5. Arbor Guard 6. Hold Down Chain... -
Page 15: Assembly And Preparation
Lock Down Chain engaged onto the Lock Down Pin. >5.1) INSTALLING Or rEMOVING A BLAdE wArNING: Only use genuine Evolution blades, or Evolution approved blades which are designed for this machine. Ensure that the maximum speed of the blade is compatible with the machine. - Page 16 www.evolutionpowertools.com • Remove the arbor screw, washer and outer blade flange and store safely for future installation. • Retract the lower blade guard up into the upper blade guard by rotating it by hand. (Fig. 5) • Remove the blade, leaving the inner blade flange in its service position.
- Page 17 www.evolutionpowertools.com If the downward travel of the Cutting head needs to be adjusted: • Loosen the locknut on the downward travel stop screw. (Fig. 7) • Turn the adjusting screw (Fig. 7) out (counter-clockwise) to decrease the downwards travel of the Cutting Head. •...
-
Page 18: Operating Instructions
www.evolutionpowertools.com (>5.2) OPErATING INSTruCTIONS (5.4) ThE ON/OFF TrIGGEr SwITCh PrEPArING TO MAKE A CuT This machine is equipped with Do not overreach. Keep good footing and a safety start trigger switch. balance. Stand to one side so that your face To start the tool: and body are out of line of a possible kickback. -
Page 19: Maintenance
www.evolutionpowertools.com (6) MAINTENANCE TrANSPOrTATION/STOrAGE For ease and convenience, when transporting (6.1) Note: Any maintenance must be carried or storing the machine, the Cutting Head can be held in the ‘down’ position. out with the machine switched off and disconnected from the mains/battery To hold the Cutting head down: power supply. -
Page 20: Declaration Of Conformity
In accordance with EN ISO 17050-1:2004 The manufacturer of the product covered by this declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below. -
Page 21: Notes
www.evolutionpowertools.com NOTES... - Page 22 Evolution Power Tools Ltd Evolution Power Tools LLC Venture One 8363 Research Drive Longacre Close Davenport Holbrook Industrial Estate Iowa Sheffield 52806 S20 3FR +44 (0)114 251 1022 866-EVO-TOOL エボリューション Evolution Power Tools Ltd パワーツール株式会社 61 Avenue Lafontaine 〒544-0031 33560 大阪府大阪市生野区...
Need help?
Do you have a question about the RAGE 2 and is the answer not in the manual?
Questions and answers