Default Setup - Rotel RSX-03 Owner's Manual

front panel STANDBY button or the remote
ON/OFF buttons.
With the DIRECT setting, the unit is fully ac-
tivated when AC power is applied and the
rear panel POWER button is ON; however,
it may be put in standby mode using the
front panel STANDBY button or the remote
ON/OFF buttons.
In ALWAYS-ON mode, the unit remains fully
active whenever AC is present and the rear
panel POWER button is ON; the front panel
STANDBY button and the remote ON/OFF
buttons are disabled and the unit cannot be
put in standby mode.
LANGUAGE: Selects a language for the
On Screen Display.
OSD ON/OFF: Select whether or not sta-
tus information (such as the volume setting)
is displayed on the TV monitor.
Change settings on the OTHER OPTIONS
menu by highlighting the desired line using
the UP/DOWN buttons and using the +/– but-
tons to step through the available settings. To
return to the MAIN menu, press the ENTER
button. Press the MENU/OSD button on the
remote to cancel the display and return to
normal operation.

Default Setup

����������������������
�����������
������������������������������
�����������������������
����������
�����������������������
�����
�����������������������
�����������������������
�����������������������
�������������
The DEFAULT SETUP menu provides access
to six functions:
• Set the tuning function for North American
or European frequencies.
• Redirect the front channel amplifiers to
power front or center back speakers.
• Restore all features and settings to the
original FACTORY DEFAULT settings.
• Activate the memorized USER DEFAULT
settings.
• Memorize a custom group of settings as
a USER DEFAULT.
39
To change the TUNER setting: Place the
highlight on the TUNER SETTING line using
the UP/DOWN buttons and use the +/– but-
tons to change the setting to N. AMERICA
or EUROPE. Then, move the highlight to the
FACTORY DEFAULT line and change the set-
ting to YES as described above. The screen
will change to a confirmation screen. Press
the ENTER button to proceed with resetting
the FACTORY DEFAULT settings and changing
the TUNER SETTING. To return to the MAIN
menu without resetting the FACTORY DEFAULT
and TUNER settings, change the entry to NO
and press the ENTER button.
To change the REDIRECT setting: Place
the highlight on the REDIRECT line using the
UP/DOWN buttons and use the +/– buttons
to change the setting to NO (for powering
front speakers) or FRONT>CB (for powering
center back speakers). If you redirect the inter-
nal amplifiers, then you will need a separate
stereo amplifier to drive your front speakers.
The CB/FRONT preamp outputs change ac-
cording to the REDIRCT setting.
: Changing the default TUNER SETTING
NOTE
or REDIRECT SETTING can only be done at
the same time as restoring the FACTORY
DEFAULT settings. Therefore, we recommend
selecting your default TUNER and REDIRECT
settings and resetting to the FACTORY DE-
FAULT settings as the first step in configuring
the unit, before you change or memorize any
other configuration settings.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the setting
to YES. Press the ENTER button to proceed
with resetting the FACTORY DEFAULT settings.
The unit will power off and then on, with
the factory settings restored. To return to the
MAIN menu without resetting the FACTORY
DEFAULT settings, change the entry to NO
and press the ENTER button.
: Resetting to factory default settings
NOTE
will erase all stored settings including delay
settings, speaker settings, balance settings,
input settings and more. You will lose ALL
system configuration settings. Be certain that
you wish to do so before resetting the fac-
tory defaults.
To memorize USER DEFAULT settings:
Many of the current configuration settings
can be stored as a USER DEFAULT, which
can be activated at any time from this menu
screen. To save the current settings as a USER
DEFAULT:
1. Place the highlight on the SET USER DE-
FAULT line using the UP/DOWN buttons
and use the +/– buttons to change the set-
ting to YES. Press the ENTER button. An
ENTER PASSWORD screen appears.
������������������������
�����������
���������
����������
������������������������
�����
��������
����������������������
2. Enter the four-digit password using the
numeric buttons on the remote. If the
password is entered correctly, the cur-
rent settings are saved as a new USER
DEFAULT.
: If you have not changed the password,
NOTE
you can use the initial password "0000".
3. To return to the DEFAULT SETUP menu
without saving any changes, use the
UP/DOWN buttons to highlight DEFAULT
SETUP MENU and press ENTER.
: If there is insufficient memory to store
NOTE
a USER DEFAULT configuration file, the SET
USER DEFAULT option will not be avail-
able.
To activate memorized USER DEFAULT
settings: After you have stored a USER
DEFAULT configuration file, you can activate
those settings at any time by placing the
highlight on the USER DEFAULT line using the
UP/DOWN buttons. Use the +/– buttons to
change the setting to YES. Press the ENTER
button to proceed with activating the USER
DEFAULT settings. To return to the MAIN
menu without activating the USER DEFAULT
settings, change the entry to NO and press
the ENTER button.
English