Front Usb Input 5; Bluetooth Connection; Audio Controls; Volume Control - Rotel RC-1570 Owner's Manual

12

Front USB Input 5

See Figure 6
The front USB input can be connected to an iPod, iPhone, USB flash memory
or the Bluetooth dongle (supplied) for wireless streaming. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.

Bluetooth Connection

Insert the supplied Bluetooth Dongle into the front USB of the RC-1570 for
wireless streaming via Bluetooth, from your device (i.e. mobile phones).
From your mobile device, look for "Rotel Bluetooth" and connect to it.
Connection is normally automatic, but if prompted for a password, please
press "0000" on your device.
NOTE: Not all Bluetooth dongles will operate with RC-1570. Please
use the one supplied.

Audio Controls

Volume Control 4 B
Turn the controls clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or - button
to turn the volume up or down. Press the MUTE
mute the volume.
Balance Control 8 C
The Balance Control adjusts the left-to-right balance of the sound output. The
factory default is the center position or "0". To change the balance from
the front panel, press the MENU
BALANCE SETTING mode. Then press the - or + buttons on the front panel to
change the value to LEFT or RIGHT. The value can change from L15 to R15.
NOTE: This setting is saved permanently including after powering off
the RC-1570.
To make temporary changes not saved after power off, from the remote
C
control press the BAL button to access the BALANCE SETTING menu,
E
then press the left/right arrow keys to adjust. When finished, press the
F
EXIT button to exit the menu.
Tone Control Bypass 8 K
Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show
TONE BYPASS. To turn on the tone control from the front panel, press the
MENU button to toggle to the Bypass control then press the - or + buttons
8
on the fornt panel to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off
the RC-1570.
To temporarily changes the Tone Control Bypass, press the BYPASS
on the remote control to toggle the Bypass mode enabled and disabled.
Bass and Treble Controls 8C
Set the Bass or Treble controls from the front panel by pressing the MENU
button to toggle to either the Bass or Treble Setting menu. Then press the - or
B
button to completely
button to toggle the front display to
8
+ button on the front panel to adjust the value. The Bass and Treble values
range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RC-1570.
To temporarily change the Bass and Treble settings from the remote control,
press the BASS or TREBLE
on the remote control to adjust the value.
A properly setup high-performance audio system produces the most natural
sound with little or no adjustment of the tone controls. Use these controls
sparingly. Be particularly careful when turning the controls up as this
increases the power output in the bass or treble range, increasing the load
on the amplifier and speakers.
NOTE: Setting the Bass and Treble controls do not automatically turn
on the tone control. To turn on tone control, refer to previous section

Tone Control Bypass.

NOTE: Tone Bypass, Bass, Treble and Balance settings are only saved
permanently from within the Menu. Adjustments made using the
buttons are temporary only and not saved after power off.
Function Control 7 J
The Function control selects the input signal source. From the front panel
or remote control press the corresponding input button to select the source
to listen to.
NOTE: Pressing the Aux, Opt and Coax keys on the front panel will
toggle between input 1 and input 2.

Dimmer Control

Display Dimmer 8 L
To change the brightness of the front display, press the MENU
to toggle to the Display Settings. Then press the - or + buttons on the front
panel to change the display brightness.
NOTE: This setting is saved permanently including after powering off
the RC-1570.
To temporarily change the display brightness, press the DIM
the remote control.
NOTE: Display Dimmer setting is only saved permanently from within
the Menu. Adjustment made using the
not saved after power off.

Rotel Link 0

This 3.5 mm stereo mini-jack (labeled ROTEL LINK IN) can optionally attach
K
button to Rotel network enabled products with ROTEL LINK OUT connections. This
allows the attached Rotel products to communicate with each other and
be controlled via the Rotel Remote App (available for download on the
iTunes store).
®
8
RC‑1570 Stereo Control Amplifier
C
button, then press the left/right
button is temporary only and
L
E
arrow keys
CK
button
8
L
button on