Instructions; Unpacking; Installation; Regulations - Dru Apollo 80 Instructions For Installation Manual

test the gastightness of all connections before use;
➠
use heat-resistant electrical connection materials;
➠
install the electrical connections away from the appliance;
➠
replace torn or broken panes;
➠
avoid blocking the explosion hatches;
➠
ensure the explosion hatches on top of the heater are right on their seats, before you close the chimney breast;
➠
do not ignite the appliance until installation has been completed.
➠

4. Instructions

Toensuretheapplianceworkscorrectlyandsafely,alwaystakethefollowingpointsintoconsiderationduringinstallation:
place the control box supplied as low as possible;
➠
ensure the ignition wire does not lie across the receiver;
➠
ensure the ignition wire does not touch or cross the aerial;
➠
to avoid weakening the spark ensure the ignition wire does not touch anything metal;
➠
if the appliance is to be built in flush with the wall, finish the edges neatly;
➠
do not plaster over the flanges;
➠
avoid damaging the glass when removing/fitting the window pane;
➠
to prevent dirt burning into the glass, make sure it is clean before use.
➠
make sure that the wires of thermocouple 2 cannot come into contact with hot parts.
➠
5.

Unpacking

Pleasetakethefollowingpointsintoconsiderationwhenunpackingtheappliance:
Check the appliance for transit damage;
➠
Contact DRU Service if necessary.
➠
Oncethepackagingmaterialhasbeenremoved,youshouldhavethefollowingcomponents:
- S ocket spanner: Youwillfindthisinthespacebetweentheassemblyframeandthecombustionchamber;
- T rimmings: Theseareinthesamespace.
Onceyouhaveremovedtheglasspaneyoucanremovetheboxofcomponentsfromthecombustionchamber.
Be careful not to damage the glass when removing/fitting the window pane.
!N.B.
Remove the window as described in paragraph 6.10.1;
➠
Take the box of components out of the combustion chamber.
➠
Annex1/Table4specifiesthecomponentsyoushouldhaveonceeverythinghasbeenunpacked.
Contact DRU Service if after unpacking the appliance you do not have all the components;
➠
Dispose of the packaging in an appropriate manner.
➠

6. Installation

Pleasereadthemanualcarefullytoensurethatonceinstalledtheappliancewillworkcorrectlyandsafely.
Install the appliance in the order described in this chapter.
!N.B.

6.1 Regulations

- Observethecurrentapplicable(installation)regulations;
- Observetheregulations/instructionslaiddowninthismanual.
6.2 Gas type
Thetypeplatespecifiesthetypeofgas,gaspressure,andthecountrythisapplianceisintendedfor.Thetypeplate
isonachainandthatiswhereitshouldstay.
Check that the appliance is suitable for the local gas type and pressure.
N.B.
6.3 Gas connection
Thegasconnectionshouldhaveagastaplocatedneartheappliance.
Prevent any dirt getting into the gas pipes or connections.
N.B.
Thefollowingrequirementsapplyforthegasconnection:
the size of the gas pipe should be such that no pressure loss can occur;
➠
the gas tap must be CE marked;
➠
the gas tap should be accessible at all times;
➠
Do not twist the gas tap when connecting the gas pipe.
➠
U K 4
A 80 -
p o l l o i n s t r u c t i o n f o r i n s tA l l At i o n