Hitachi Koki C10FCH2 Instruction Manual page 9

I English
6mm Wing bolt
Steel (Optional accessory)
Holder
square X
, (Optional _'_:_-_-
accessory) __i
6mm Wing
nut (Optional
accessory) Height adjustment Base surface
bolt 6mm (Optional
accessory)
Fig.9
Stopper for precision cutting ... (Stopper and holder are optional
accessory)
Thestopper facilitatescontinuousprecision cutting in lengthsof 11"
to 17-3/4"(280mmto 450mm).
To installthe stopper,attach it to the holderwith the 6ramwing bolt
asshown in Fig.10.
Stopper
Workpiece (Optional accessory)
Holder
(Optional accessory)
./K CAUTION:
I
LASER R ADIATION-DO NOT
_ TARE INTO BEAM
Maximum Output:<lmW,
Wavelength:4OO~7OOnm,
Laser M edium: LaserDiode
CLASS I TLASER PRODUCT.
Complies with21CFR,
Chapter t , Subchapter J.
Laser radiation on worktable.
_DO NOT STAREINTO BEAM.
Fig.12
Move
6mm Wing nut
(Optional accessory)
6mm Wing bolt Height adjustment bolt 6mm
(Optional accessory) (Optional accessory)
Fig.10
Confirmation for use of sub fence (B) ...(Standardaccessory)
Z_ WARNING:
In the case of left bevelcutting,rotatethe subfence(B).Supposing
it isnotableto rotateit, It will contactthe bladeor somepartofthe
tool,causingin seriousinjuryto operator.
Sub fence (B)
Fence (B) _!_.L_"- ".........
Fig.11
6. Position adjustment of laserline (Only Model C10FCH2)
,/_ WARNING:
* Make surebeforepluggingthe power plug into the receptacle
that the mainbodyandthe lasermarkerare turnedoff.
* Exerciseutmost cautionin handlinga switch trigger for the
position adjustment o fthe laserline,asthepowerplugisplugged
into the receptacle duringoperation.
If the switch triggeris pulledinadvertently, t he saw blade can
rotateandresultin unexpected accidents.
* Do not removethe lasermarkerto beusedfor other purposes.
( • AVOIDEXPOSURE'_
/ ^ T Laser radiation|
I /_' is emitted from I
Fig.13
* Laserradiation-- Donot stareinto beam.
* Laserradiationonwork table.Do not stareintobeam.
If youreye isexposeddirectlyto the laserbeam, it canbe hurt.
* Donot dismantleit.
* Donotgivestrongimpacttothe lasermarker (mainbodyoftool);
otherwise, t heposition ofalaserlinecangooutoforder,resulting
in the damageof the lasermarkeras well asa shortened service
life.
* Keep the laser marker lit only during a cutting operation.
Prolonged lightingof the lasermarkercanresultin a shortened
servicelife.
* Use of controlsor adjustmentsor performance of procedures
other than those specifiedherein may result in hazardous
radiation exposure.
NOTE:
Perform cuttingby overlapping the inkline with the laserline.
Whenthe ink lineandthe laserlineareoverlapped, t he strength
andweaknessof lightwill change,resultingin a stablecutting
operationbecause you caneasilydiscern the conformity of lines.
Thisensures the minimumcuttingerrors.
Inoutdoor or near-the-window operations, it maybecomedifficult
to observe the laser line due to the sunlight. Under such
circumstances, move to a placethat is not directlyunderthe
sunlight a ndengagein the operation.
Donottugonthe cordbehindthemotorheador hookyourfinger,
wood and the likearoundit; otherwise,the cordmay come off
andthe lasermarkermay not belit up.
Ink lining can be easily made on this tool to the laser marker. A
switch lights up the lasermarker. (Fig. 14)
Depending upon your cutting choice, the laser line can be aligned
with the left side of the cutting width (saw blade)or the ink line on
the right side.