Replacement Parts; Environmental Information - Flymo Power Trim SET250 Original Instructions Manual

WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS
CLATTERING NOISE
LINE SNAPS
CONTINUOUSLY
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
Spool and Line
Reference no.:
Part no.:
• Awareness of the environment must be considered
when disposing of 'end-of-life' product.
• If necessary, contact your local authority for disposal
information.
The symbol on the product or on its packaging indi-
cates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic
equipment.
If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna UK Ltd., through its Authorised
Service Repairers will effect the repair or replacement to the cus-
tomer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjustment
by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart or
tampered with by any person not authorised by Husqvarna UK
Ltd.
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is important
that you read the instructions contained in this Operator's Manual
and understand how to operate and maintain your machine:
Fault Finding Chart
Is the automatic line feed work-
ing?
Is the line fed out and visible?
Has line been removed from
cleat?
Is the manual line feed working?
Has the motor reached full speed
before use?
Has too much line been fed out?
Is the line cutter missing from the
safety guard?
Are you using the trimmer
correctly?
Is the line jamming on the spool?
Contact Husqvarna UK Ltd. Customer Service
Telephone : 0844 844 4558 UK

Replacement Parts

FLY021
513937190

Environmental Information

Guarantee & Guarantee Policy
CHECK
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the en-
vironment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or the shop where you
purchased the product.
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with
the instructions and recommendations contained in this Oper-
ator's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and
their life is dependent on regular maintenance and are, there-
fore not normally subject to a valid warranty claim: Nylon Line,
Spool and Line, Electric Mains Cable
* Caution!
Husqvarna UK Ltd. does not accept liability under the warranty
for defects caused in whole or part, directly or indirectly by the
fitting of replacement parts or additional parts that are not ei-
ther manufactured or approved by Husqvarna UK Ltd., or by
the machine having been modified in any way.
ACTION
Manually feed out line.
No
SEE "MANUAL LINE FEED"
Remove cap and spool, free line
No
and re-fit spool and cap. SEE "CUT-
TING HEAD"
The line may be jammed on the
spool. Rewind line to remove
No
crossed loops. Check that line is in
correct section of spool.
Allow the motor to reach full speed
No
before use.
Yes
SEE "MANUAL LINE FEED"
Contact your local approved Serv-
Yes
ice Centre or Husqvarna UK Ltd.
Customer Service.
Only use tip of nylon line to trim.
?
SEE "How to trim and edge"
Rewind the line on the spool, if
Yes
symptoms still persist, change
spool and line.
1800 882 350 ROI