Sony DVP-F21 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. DVD Player
  5. DVP-F21 - Cd/dvd Player
  6. Service manual
Sony DVP-F21 Service Manual

Sony DVP-F21 Service Manual

Cd/dvd player, remote commander rmt-d137a/rmt-d137p
Hide thumbs Also See for DVP-F21:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL

Specifications

System
Laser
Semiconductor laser
Signal format system
NTSC (EXCEPT AEP, UK)
PAL (AEP, UK)
Audio characteristics
Frequency response
DVD (PCM 96 kHz): 2 Hz to 44 kHz (±1.0 dB)
DVD (PCM 48 kHz): 2 Hz to 22 kHz (±0.5 dB)
CD: 2 Hz to 20 kHz (±0.5 dB)
Signal-to-noise ratio (S/N ratio)
115 dB (AUDIO OUT L/R jacks only)
Harmonic distortion
0.003%
Dynamic range
DVD: 103 dB
CD: 99 dB
Wow and flutter
Less than detected value (±0.001% W PEAK)
The signals from AUDIO OUT L/R jacks are measured. When you play PCM sound tracks with a 96 kHz sampling
frequency, the output signal from the DIGITAL OUT (OPTICAL) jack is converted to 48 kHz sampling frequency.
Outputs
Jack name
Jack type
DIGITAL OUT
Optical output jack
(OPTICAL)
AUDIO OUT L/R
Phono jack
VIDEO OUT
Phono jack
S-VIDEO OUT
4-pin mini DIN
SPECIFICATIONS
Maximum output
Load impedance
level
-18 dBm
Wave length 660 nm
2 Vrms (50 kilohms)
Over 10 kilohms
1.0 Vp-p
75 ohms, sync negative
Luminance signal:
75 ohms, sync negative
1.0 Vp-p
Color signal:
75 ohms terminated
0.286 Vp-p (NTSC)
0.3 Vp-p (PAL)
DVP-F21
RMT-D137A/RMT-D137P
General
Power requirements
DC 10.5 V
See page 3 for further information.
Power consumption
12 W
252 × 60 × 183 mm (10 × 2 3/8 × 7 1/4 in.) (width/height/depth)
Dimensions (approx.)
including projecting parts
Mass (approx.)
1.5 kg (3 lb 5 oz)
Operating temperature
5°C to 35°C (41°F to 95°F)
Operating humidity
25% to 80%
AC power adaptor
Mo
del name
AC-F21
Power requirements
100 to 240 V AC, 50/60 Hz
Output voltage
DC 10.5 V, 1.3 A in operating mode
Operating temperature
5°C to 35°C (41°F to 95°F)
Storage temperature
–20°C to 60°C (–4°F to 140°F)
Supp
lied accessories
• Audio/video cord (pinplug × 3 ←→ pinplug × 3) (1)
• Remote commander (remote) RMT-D137A (1) (US, CND, MX)
RMT-D137P (1) (EXCEPT US, CND, MX)
• Size AA (R6) batteries (2)
• AC power adaptor AC-F21 (1)
• AC power cord (1)
• Jack cover for vertical installation (1)
Optional accessory
Active Speaker System SA-F21
Specifications and design are subject to change without notice.
TAR  is a U.S. registered mark. As an
E
S
E
NERGY
TAR  guidelines for energy efficiency.
E
S
that this product meets the
NERGY
US Model
Canadian Model
AEP Model
UK Model
Mexico Model
Hong Kong Model
Singapore Model
TAR  Partner, Sony Corporation has determined
S
NERGY
CD/DVD PLAYER

Advertisement

Table of Contents
loading

Related Manuals for Sony DVP-F21

Summary of Contents for Sony DVP-F21

  • Page 1: Specifications

    S-VIDEO OUT 4-pin mini DIN Luminance signal: 75 ohms, sync negative TAR  is a U.S. registered mark. As an TAR  Partner, Sony Corporation has determined NERGY NERGY 1.0 Vp-p TAR  guidelines for energy efficiency. that this product meets the...
  • Page 2 MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM-POSANTS QUE PAR DES PIÈCES SONY COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Section Title Page Section Title Page GENERAL IC PIN FUNCTION DESCRIPTION 5-1. System Control PIN Function (MB-99 Board IC103) ..5-1 DISASSEMBLY 5-2. System Control PIN Function (FL-123 Board IC403) ..5-2 2-1. Terminal Cover, Lower Case .......... 2-1 TEST MODE 2-2.

  • Page 5: General

    DVP-F21 SECTION 1 GENERAL This section is extracted rom instruction manual (3-070-343-11). Region code About this Manual Your player has a region code printed on the back of the unit and will only play DVDs • Instructions in this manual describe the labeled with identical region codes.
  • Page 6 Front Panel Display Side Panel When playing back a DVD Playing status Lights up when you Current audio signal can change the angle (DTS format signal) (72) Current play mode (A-B Disc type Repeat Play) (44) A DC IN 10.5 V jack (17) B AUDIO OUT L/R jacks (17, 23, 24, 26) Lights up when BNR is C DIGITAL OUT (OPTICAL) jack (24,...

  • Page 7: Quick Overview

    Control Bar Getting Started The Control Bar appears when a playback function is selected by pressing the function’s button on the remote. Quick Overview Playback function icon. A quick overview presented in this chapter will give you enough information to start using the 2 ( 7 ) player for your enjoyment.

  • Page 8: Hooking Up The Player

    Step 4: Playing a Disc Hookups A Turn on the TV. Hooking Up the Player B Switch the input selector on the TV to the player. Follow Steps 1 to 5 to hook up and adjust the settings of the player. Before you start, turn off the power, check that you have all of the supplied accessories, and insert Remote sensor Remote sensor...
  • Page 9 Connecting to your TV Step 2: Connecting the Audio Cords This connection will use your TV speakers for sound. Refer to the chart below to select the connection that best suits your system. The surround effects xRecommended surround sound effects for this connection. you will enjoy depend on the connections and components you use.
  • Page 10 Connecting to a Dolby Surround (Pro Logic) decoder amplifier (receiver) and CD/DVD player 3 to 6 speakers This connection will allow you to enjoy the surround effects of the Dolby Surround (Pro Logic) decoder on your amplifier (receiver). If you have an AV amplifier (receiver) equipped with a Dolby Digital or DTS decoder, refer to page 28.
  • Page 11 When you install the player on the wall Step 3: Attaching the Jack Cover When you install the player on the wall, ask a qualified installer to do the job. The player should be installed in the following way. You can install the player horizontally, vertically or on the wall. Attach the jack cover as in the same way for the horizontal installation.

  • Page 12: Playing Discs

    If you disconnect the AC power cord. Doing so may preceding chapter, cannot eject the disc, consult your nearest Sony cancel the menu settings. When you turn off track, or scene in Switch the input selector on the TV dealer.
  • Page 13 Using the menu Notes Resuming Playback from Using the DVD’s Menu • Depending on where you stopped the disc, the player Some DVDs allow you to select the disc the Point Where You may not resume playback from exactly the same contents using a menu.
  • Page 14 Next, press X/x to select “03” under Press X/x to select “SETt” and press Press H to start Program Play. Playing in random order (Shuffle “C,” then press ENTER. Play) ENTER. Program Play begins. The display for programming appears. When the program ends, you can restart PROGRAM You can have the player “shuffle”...
  • Page 15 Opposite direction x2b (DVD only) t 1m t 2m Searching for a Title/ Press SEARCH MODE repeatedly to Searching for a Scene select the search method. Chapter/Track/Index/ x When playing a DVD Searching for a Particular Scene The “x2B”/”x2b” playback speed is about (Search mode) (TITLE), (CHAPTER),...
  • Page 16 If the DVD/CD text does not fit on a single line, Press TIME/TEXT repeatedly to you can see the entire text by watching it scroll across Press AUDIO repeatedly to select the the front panel display. change the time information. Sound Adjustments desired audio signal.

  • Page 17: Displaying The Subtitles

    TVS NIGHT • “TVS NIGHT” only works with Dolby Digital discs. However, not all discs will respond to the “TVS Displaying the Subtitles The large sounds, such as explosions, are NIGHT” function in the same way. Enjoying Movies suppressed, but the quieter sounds are •...
  • Page 18 Enter a new 4-digit password using X/x Press X/x to select (CUSTOM Enter or re-enter your 4-digit password to select the digit, followed by c to move Using Various Additional by pressing X/x to select the digit, PARENTAL CONTROL), then press Functions the cursor.

  • Page 19: With The Supplied Remote

    Philips • Depending on the units being connected, you may Quasar not be able to control your TV or Sony AV amplifier (receiver) using some of the buttons below. • If you enter a new TV code, the code previously Samsung entered will be erased.

  • Page 20: Using The Setup Display

    Press X/x to select Select an item using X/x, then press (SETUP) and Setting the Display or press ENTER. ENTER. Settings and Adjustments Sound Track Language The options for “SETUP” appear. The options for the selected item appear. Using the Setup Display Example: “TV TYPE”...
  • Page 21 xDIMMER Notes Custom Settings Settings for the Sound (CUSTOM Adjusts the lighting of the front panel display. • When you set the item to “AUTO,” the language SETUP) (AUDIO SETUP) may change. The “TRACK SELECTION” setting BRIGHT Makes the front panel display has higher priority than the “AUDIO”...
  • Page 22 Parental Control functions are provided with of the display. Dolby Surround (Pro Logic) (page 71) the DVD. service , Contact your Sony dealer or local authorized Audio signal processing technology that number Sony service facility. Dolby Laboratories developed for surround C 13 The disc is dirty.

  • Page 23: Language Code List

    1357 Malay 1514 Sesotho 1052 Azerbaijani 1217 Hindi 1358 Maltese 1515 Sundanese TAR  is a U.S. registered mark. As an TAR  Partner, Sony Corporation has determined NERGY NERGY 1053 Bashkir 1226 Croatian 1363 Burmese 1516 Swedish TAR  guidelines for energy efficiency.

  • Page 24: List Of Setup Display Items

    Quick Setup 32 Setup Display 66 DOLBY DIGITAL 51 DOWNMIX 72 Remote 15 DTS 51 REPEAT 44 DVD 36 Repeat Play 44 DVD’s menu 39 Replay 37 RESET 67 Resume Play 38 Fast forward 37 Sony Corporation Printed in Japan 2-20 E...

  • Page 25: Disassembly

    DVP-F21 SECTION 2 DISASSEMBLY Note : Follow the disassembly procedure in the numerical order given. 2-1. TERMINAL COVER, LOWER CASE 2-3. MECHANISM DECK 6 Mechanism deck Insert the small type flat-blade screwdriver into the groove, and 4 Screws 5 Screw (B3) 1 Ground lift up rubber foot.

  • Page 26: Md-90, Board, Lever Assembly

    2-5. MD-90, BOARD, LEVER ASSEMBLY 2-7. OPTICAL DEVICE 1 Insulator screw 1 Tension spring 3 Insulator 3 Remove lever assembly. 2 Remove optical device in the arrow 5 Screws direction. (B2.6) (2 pcs) 2 While pushing claw in the arrow direction, and remove lever assembly.

  • Page 27: Gate Assembly, Cover (T)

    2-9. GATE ASSEMBLY, COVER (T) 2-11. SLIDER (L), SLIDER (R) 3 While opening two claws 1 Move slider (R) in the arrow on the base in the arrow direction, and remove it. directions, and remove cover (T). 2 Move slider (L) in the arrow direction, and remove it.

  • Page 28: Boards

    2-13. MB-99, IR-39 BOARDS 1 Screws (B3) (3 pcs) 2 IR-39 board 4 Screws (B3) (4 pcs) 6 MB-99 board 5 Screws (B3) (3 pcs) 3 Screws (B3) (4 pcs) 2-14. Sliders (L) and (R) Phase Adjustment When installing the gear (P), the phase adjustment between sliders (L) and (R) is performed in the following position.

  • Page 29: Internal Views

    2-15. INTERNAL VIEWS...

  • Page 30: Circuit Boards Location

    2-16. CIRCUIT BOARDS LOCATION MD-90 (FUNCTION SWITCH (2)) IR-39 (IR) MB-99 (VIDEO/AUDIO/SIGNAL PROCESS/SERVO) MD-91 MD-89 (FUNCTION SWITCH (1)) FL-123 (INTERFACE CONTROL) 2-6 E...

  • Page 31: Block Diagrams

    DVP-F21 SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM MB-99 BOARD (SEE PAGE 4-11 to 32) IC303 IC504 IC601 16M DRAM 16M SDRAM BASE UNIT TK-55 BOARD KHM-240AAA/J1RP (SEE PAGE 4-11) VIDEO V, OPTICAL DEVICE VIDEO Y, IC902 VIDEO SD 0-7...

  • Page 32: Rf/Servo Block Diagram

    DVP-F21 3-2. RF/SERVO BLOCK DIAGRAM IC202 IC202 20mV/DIV 0.1µs/DIV 50mV/DIV 0.1µs/DIV 0.512Vp-p 1.5Vp-p (H) BASE UNIT KHM-250AAA/J1RP MB-99 BOARD (1/4) IC202 (SEE PAGE 4-13,14,15,16,17,18) DVD/CD RF AMP, OPTICAL DEVICE DIGITAL SERVO CN201 SIGNAL PROCESSOR RF IN SIG0 (SEE PAGE 3-5)

  • Page 33: Signal Processor Block Diagram

    DVP-F21 3-3. SIGNAL PROCESSOR BLOCK DIAGRAM MB-99 BOARD(2/4) HK, SP, MX, AEP, UK (SEE PAGE 4-15,16,19,20) IC504 IC505 16M SDRAM 16M SDRAM IC303 16M DRAM IC503 IC302 0.9Vp-p (H) IC503 124 125 127 128 MA 0-9 136 137 139 140 MA 0-15 1.5Vp-p (H)

  • Page 34: System Control Block Diagram

    DVP-F21 3-4. SYSTEM CONTROL BLOCK DIAGRAM MB-99 BOARD(3/4) (SEE PAGE 4-11,12) IC107 IC108 FLASH HA 0-21 HA 0-21 HD 0-15 HA 0-15 (SEE PAGE 3-5,6) (SEE PAGE 3-3) MD-91 BOARD MD-89 BOARD (SEE PAGE 4-39) (SEE PAGE 4-33) HA 0-21...

  • Page 35: Video Block Diagram

    DVP-F21 3-5. VIDEO BLOCK DIAGRAM 3-6. AUDIO BLOCK DIAGRAM MB-99 BOARD MB-99 BORAD (4/4) (SEE PAGE 4-25,26) (SEE PAGE 4-27,28) IC902 VIDEO BUFFER IC1001 J901 DIGITAL IC503 SRDIF 1 D IN OPTICAL 3 VIDEO IN VIDEO OUT VIDEO1 LINE OUT...

  • Page 36: Interface Control Block Diagram

    DVP-F21 3-7. INTERFACE CONTROL BLOCK DIAGRAM 3-8. POWER BLOCK DIAGRAM FL-123 BOARD MB-99 BOARD CN404 IC403 (SEE PAGE 4-37,38) (SEE PAGE 4-23,24) SHORT PROTECT IF CONTROL EVER 3.3V Q703 AC IN J701 LF702 D702 D707 AC ADAPTER DC IN 10.5V...

  • Page 37: Printed Wiring Boards And Schematic Diagrams

    DVP-F21 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR PRINTED WIRING For schematic diagram: • Caution when replacing chip parts. BOARDS AND SCHEMATIC DIAGRAMS. New parts must be attached after removal of chip. (In addition to this, the necessary mote is printed in Be careful not to heat the minus side of tantalum capacitor, each block.)

  • Page 38: Frame Schematic Diagram

    DVP-F21 4-1. FRAME SCHEMATIC DIAGRAM FRAME SCHEMATIC DIAGRAM CN101 26P CN201 26P MB-99 BOARD TRK- FOB-1 OPTICAL TRK+ DEVICE FCS- FCS+ N.C. CD LD N.C. DVD LD LD GND IR-39 BOARD SW/N.C. LD GND DVD LD N.C. 6 CD LD/N.C.

  • Page 39: Printed Wiring Boards And Schematic Diagrams

    DVP-F21 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS IR-39 (IR) PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS – Ref. No.: IR-39 board; 50,000 series – IR-39 BOARD There are a few cases that the part isn’t mounted in this model is printed on this diagram.

  • Page 40: Video/Audio/Signal Process/Servo) Printed Wiring Board

    DVP-F21 MB-99 (VIDEO/AUDIO/SIGNAL PROCESS/SERVO) PRINTED WIRING BOARD – Ref. No.: MB-99 board; 60,000 series – There are a few cases that the part isn’t mounted in this model is printed on this diagram. MB-99 BOARD (SIDE A) MB-99 BOARD (SIDE A)
  • Page 41 DVP-F21 MB-99 BOARD (SIDE B) MB-99 BOARD (SIDE B) D403 D701 D706 JL702 JL706 D707 JL712 C723 FB701 FL703 D901 C715 R709 R748 R732 JL711 PS704 C713 R749 C714 R762 D902 R182 JL708 C718 C706 JL704 RB101 JL710 D903 R169...

  • Page 42: System Control) Schematic Diagram

    DVP-F21 MB-99 (SYSTEM CONTROL) SCHEMATIC DIAGRAM • See page 4-7, 9 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – • Waveforms 1 IC103 %¢ MB-99 BOARD (1/11) MB-99 BOARD +3.3V (2/11,3/11,4/11,5/11, 6/11,7/11,8/11,11/11) IC107 FLASH IC107 MBM29LV160BE-90TN...

  • Page 43: Rf Servo) Schematic Diagram

    DVP-F21 MB-99 (RF SERVO) SCHEMATIC DIAGRAM • See page 4-7 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (2/11) JL230 MB-99 BOARD (1/11) +3.3V RFMON MB-99 BOARD (1/11,4/11) MB-99 BOARD (3/11) C231 C232 C222 C225 0.1u...

  • Page 44: Signal Process) Schematic Diagram

    DVP-F21 MB-99 (SIGNAL PROCESS) SCHEMATIC DIAGRAM • See page 4-7 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (3/11) KTEMU0 MB-99 BOARD (3/11) SDI7 KTEMU1 SDI7 SDEF SDI6 SDI6 SDI5 XSAK SDI5 XSRQ SDI4...

  • Page 45: Servo) Schematic Diagram

    DVP-F21 MB-99 (SERVO) SCHEMATIC DIAGRAM • See page 4-9 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (4/11) EVER+3.3V +3.3V MB-99 BOARD (1/11) R432 JL401 C416 0.01u C414 R427 R430 0.01u R433 100k 100k ±...

  • Page 46: Signal Process) Schematic Diagram

    DVP-F21 MB-99 (SIGNAL PROCESS) SCHEMATIC DIAGRAM • See page 4-7 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (5/11) MB-99 BOARD (1/11,3/11,11/11) XWRH XAVDIT XKAVWT DACK0 MB-99 BOARD (1/11) DREQ0 XAVDCS3 DACK1 MB-99 BOARD (1/11)

  • Page 47: Signal Process) Schematic Diagram

    DVP-F21 MB-99 (SIGNAL PROCESS) SCHEMATIC DIAGRAM • See page 4-9 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (6/11) C602 0.01u PDO0 PDI5 PDI7 PDO0 YCOUT5 PDI7 PDO1 PDO5 PDI4 PDI6 PDO1 YCIN_5 YCOUT4...

  • Page 48: Power) Schematic Diagram

    DVP-F21 MB-99 (POWER) SCHEMATIC DIAGRAM • See page 4-9 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (7/11) R759 R760 D707 1SR154-400TE-25 J701 LF702 AU+11V REG R713 D702 FL701 JL718 JL701 RB081L-20TE25 – 10.3 10.3...

  • Page 49: Av Out) Schematic Diagram

    DVP-F21 MB-99 (AV OUT) SCHEMATIC DIAGRAM • See page 4-9 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (8/11) C806 0.01u C804 N.C. C802 R802 0.01u MB-99 BOARD (1/11) 512FS6CH MCLK IC801 CXD9626Q R828...

  • Page 50: Video) Schematic Diagram

    DVP-F21 MB-99 (VIDEO) SCHEMATIC DIAGRAM • See page 4-7 for printed wiring board. • Waveforms 1 IC902 3 – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (9/11) IC902 L901 100uH VIDEO BUFFER AU_GND MB-99 BOARD (7/11) AI+5V MB-99 BOARD (10/11) B–...

  • Page 51: Audio) Schematic Diagram

    DVP-F21 MB-99 (AUDIO) SCHEMATIC DIAGRAM • See page 4-9 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (10/11) R1007 R1014 4700 ±0.5% 2200 C1012 ±0.5% 0.01u ART- C1016 R1018 C1006 5600 R1024 560p ±0.5% 6.3V...

  • Page 52: Avms) Schematic Diagram

    DVP-F21 MB-99 (AVMS) SCHEMATIC DIAGRAM • See page 4-7 for printed wiring board. – Ref. No.: MB-99 board; 60,000 series – MB-99 BOARD (11/11) R1130 R1128 100k CN1102 DSP_TMS DSP_TRST TRST IC1103 +3.3V B+ REG IC1103 XC62FP1502PR IC1105 DSP_TCK R1168...

  • Page 53: Function Switch 1) Printed Wiring Board And Schematic Diagram

    DVP-F21 MD-89 (FUNCTION SWITCH 1) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: MD-89 board; 20,000 series – There are a few cases that the part isn’t mounted in this model is printed on this diagram. MD-89 BOARD MD-89 BOARD (SIDE A)

  • Page 54: Interface Control

    DVP-F21 FL-123 (INTERFACE CONTROL) PRINTED WIRING BOARD – Ref. No.: FL-123 board; 40,000 series – There are a few cases that the part isn’t mounted in this model is printed on this diagram. FL-123 BOARD (SIDE A) FL-123 BOARD (SIDE A)
  • Page 55 DVP-F21 FL-123 (INTERFACE CONTROL) SCHEMATIC DIAGRAM – Ref. No.: FL-123 board; 40,000 series – • Waveforms 1 IC403 3 FL-123 BOARD C416 0.01u R404 R481 CN403 JL404 3.3V_MNT GRNA GRNK JL405 R480 XFRRST JL406 REDA REDK R405 ND402 XIFBUSY JL407...

  • Page 56: Function Switch) Printed Wiring Board And Schematic Diagram

    DVP-F21 MD-90 (FUNCTION SWITCH) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: MD-90 board; 30,000 series – MD-90 BOARD There are a few cases that the part isn’t mounted in this model is printed on this diagram. S301 TP301...

  • Page 57: Ic Pin Function Description

    DVP-F21 SECTION 5 IC PIN FUNCTION DESCRIPTION...
  • Page 58 5-2 E...

  • Page 59: Test Mode

    DVP-F21 SECTION 6 TEST MODE 6-1. GENERAL DESCRIPTION ### Syscon Diagnosis ### Check Menu The Test Mode allows you to make diagnosis and adjustment 0. Quit easily using the remote commander and monitor TV. The 1. All instructions, diagnostic results, etc. are given on the on-screen 2.
  • Page 60 The model code read from the EEPROM is displayed each item. with 2-digit hexadecimal number. For example, if “5. Supply” is selected, the following submenu will be displayed. Model Type DVP-F21 ### Syscon Diagnosis ### Check Menu No. 5 Supply 0. Quit 1. All 2.
  • Page 61 5. Supply ### Syscon Diagnosis ### (5-2) ARP Register Check Data write → read, and accord check Error 08: ARP register write, and read data discord Data 0x00 to 0xFF is written sequentially to the ARP 5-4. ARP to RAM Address Bus TMAX register (address 0xC6) and then read for Error 10: ARP - RAM Address B checking.
  • Page 62 7. Video Check Items List Version (7-2) Color Bar (2-2) Revision AVD color bar command write → Video OUT (2-3) ROM Check Sum Error: Not detected. (2-4) Model Type The command is transferred to the AVD, and the color bar (2-5) Region signals are output from video terminals.

  • Page 63: Drive Auto Adjustment

    6-4. DRIVE AUTO ADJUSTMENT 1. DVD-SL (single layer) [ENTER] Select , insert DVD single layer disc, and press key, On the Test Mode Menu screen, press key on the remote and the adjustment will be made through the following steps, then commander, and the drive auto adjustment menu will be adjusted values will be written to the EEPROM.
  • Page 64 2. CD 3. DVD-DL (dual layer) [ENTER] [ENTER] Select , insert CD disc, and press key, and the Select , insert DVD dual layer disc, and press key, adjustment will be made through the following steps, then and the adjustment will be made through the following steps, then adjusted values will be written to the EEPROM.

  • Page 65: Drive Manual Operation

    6-5. DRIVE MANUAL OPERATION On this screen, the mirror time is measured and written to the EEPROM to check the disc type. First, set a DVD SL disc and press , then set a CD disc and press , and finally set a DVD On the Test Mode Menu screen, select , and the manual DL disc and press...
  • Page 66 Reset SLED TILT Reset the Sled and Tilt to initial Disc Type position. 1. Disc Type Auto Check Turn ON/OFF the laser. 2. DVD SL 12 cm Turn ON/OFF the spindle. 3. DVD DL 12 cm Focus Search the focus and turn on the focus. 4.
  • Page 67 Auto TRK. Offset Adjusts tracking offset. 4. Manual Adjustment Auto Focus Balance Adjusts focus balance. Auto Focus Offset Adjusts focus offset. Manual Adjustment Auto Focus Gain Adjusts focus gain. 1. TRK. Offset Auto TRK. Gain Adjusts track gain. 2. Focus Gain Auto EQ 3.

  • Page 68: Mecha Aging

    6-6. MECHA AGING How to see Emergency History ### Mecha Aging ### Press OPEN key 1: Emergency Code 2: Don’t Care (These codes are used for verification of software Abort: STOP key designing.) 3: Historical order 1 to 9 Emergency Codes List On the Test Mode Menu screen, selecting executes the aging 10: Communication to IC202 (MB-99 board) failed.
  • Page 69 FLD Auto Self Check FLD and LED all ON (for 5 seconds) HOUR TITLE CHAP TRACK V C D ANGLE D V D NTSC Digital Model display (for 2 seconds) TRACK HOUR TITLE CHAP V C D ANGLE D V D NTSC Digital Version display (for 2 seconds)

  • Page 70: Version Information

    6-8. VERSION INFORMATION 6-10. IF CON Function Check Mode ## Version Information ## 1. Button function [POWER] When any button except of the main unit is pressed in IF con. Ver : x. xxx (xxxx) the Test mode, the unit exits from the Self Check mode of the Group fluorescent display tube.
  • Page 71 3. SYSTEM CONTROL - IF CON serial communication The IF CON and SYSTEM CONTROL are usually performing both-directions communication in a cycle of 24 ms. This mode checks in simple whether this communication is performed normally. When “NOTHING” is displayed and the character [VCR] [DVD] [CD]...
  • Page 72 Dp ( 2G~7G ) ( 2G~8G ) ( 2G~8G ) ( Grid ) 6-14...

  • Page 73: Troubleshooting

    6-11. TROUBLESHOOTING 5. Grid check ( button: Grid check mode) This check mode makes it turn on one grid of the arbitrary grids of fluorescent display at a time. (All anodes of applicable grid are 1. Cannot Enter Test Mode turned on.) During this check mode, grid of one somewhere You cannot enter the Test mode when either button has been [CLICK SHUTTLE]...

  • Page 75: Electrical Adjustment

    DVP-F21 SECTION 7 ELECTRICAL ADJUSTMENT 7-1. POWER SUPPLY CHECK In making adjustment, refer to 7-4. Adjustment Related Parts Arrangement. 1. MB-99 Boards Note: During diagnostic check, the characters and color bars can be seen only with the NTSC monitor. Therefore, for...

  • Page 76: Adjustment Of Video System

    7-2. ADJUSTMENT OF VIDEO SYSTEM 3. Checking S Video Output S-C <Purpose> 1. Video Level Adjustment (MB-99 BOARD) This checks whether the S-C satisfies the NTSC/PAL Standard. If it is not correct, the colors will be too dark or light. <Purpose>...

  • Page 77: Repair Parts List

    DVP-F21 SECTION 8 REPAIR PARTS LIST 8-1. EXPLODED VIEWS NOTE: • The mechanical parts with no reference number in The components identified by mark the exploded views are not supplied. ! or dotted line with mark ! are criti- • -XX and -X mean standardized parts, so they may cal for safety.

  • Page 78: Mech.deck Block (1)

    DVP-F21 8-1-2. MECH.DECK BLOCK (1) not supplied Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks X-3951-919-1 GATE ASSY 3-070-577-01 RACK (L) 3-070-596-01 SPRING,COMPRESSION 1-823-246-11 CABLE, FLEXIBLE FLAT (FDM-22) X-3951-920-1 LEVER ASSY X-3951-914-1 MOTOR (C) ASSY 3-703-358-05 PIN,PARALLEL (DIA.2X16)

  • Page 79: Mech.deck Block (2)

    DVP-F21 8-1-3. MECH.DECK BLOCK (2) Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks 3-070-554-01 GEAR (P) 3-070-586-01 CAP, S X-3951-913-1 SLIDER (L) ASSY 3-070-558-01 ROLLER, S 3-968-729-81 SCREW (2X3) X-3951-916-1 STOPPER (R) ASSY 1-823-247-11 CABLE, FLEXIBLE FLAT (FDD-11)

  • Page 80: Chassis Block

    DVP-F21 8-1-4. CHASSIS BLOCK Ref.No. Part No. Description Remarks * 151 A-6065-721-A FL-123 BOARD, COMPLETE 3-071-630-01 COVER FL 3-055-791-11 SUMITITE (B3) (RING), +BV 1-823-268-11 CABLE, FLEXIBLE FLAT (FFM-38) 1-823-269-11 CABLE, FLEXIBLE FLAT (FIF-2) * 156 A-6065-722-A IR-39 (UC) BOARD, COMPLETE...

  • Page 81: Electrical Parts List

    DVP-F21 MD-91 MD-89 MD-90 MB-99 8-2. ELECTRICAL PARTS LIST NOTE: • Items marked “*” are not stocked since they are The components identified by mark seldom required for routine service. ! or dotted line with mark ! are criti- • Due to standardization, replacements in the parts cal for safety.
  • Page 82 DVP-F21 MB-99 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks C222 1-107-826-11 CERAMIC CHIP 0.1UF 10.00% C349 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% C223 1-126-205-11 ELECT CHIP 47UF 20.00% 6.3V C350 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% C224 1-162-970-11 CERAMIC CHIP 0.01UF...
  • Page 83 DVP-F21 MB-99 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks C537 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% C809 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% (AEP, UK, HK, SP) C901 1-162-970-11 CERAMIC CHIP 0.01UF 10.00% C538 1-162-970-11 CERAMIC CHIP 0.01UF 10.00%...
  • Page 84 DVP-F21 MB-99 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks <FERRITE BEAD> J903 1-815-894-11 JACK, PIN (2P) (AUDIO OUT L/R) FB104 1-216-295-91 SHORT 0 (HK, SP) <COIL> FB104 1-469-324-21 FERRITE 0UH (Except HK, SP) FB112 1-469-836-21 FERRITE L201...
  • Page 85 DVP-F21 MB-99 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks <RESISTOR> R167 1-216-809-11 RES-CHIP 1/16W R168 1-216-809-11 RES-CHIP 1/16W R101 1-216-789-11 RES-CHIP 1/16W R105 1-216-864-11 SHORT R169 1-216-809-11 RES-CHIP 1/16W R106 1-216-833-11 RES-CHIP 1/16W R170 1-216-821-11 RES-CHIP 1/16W...
  • Page 86 DVP-F21 MB-99 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks R315 1-216-817-11 RES-CHIP 1/16W R432 1-216-833-11 RES-CHIP 1/16W R316 1-216-829-11 RES-CHIP 4.7K 1/16W R433 1-216-833-11 RES-CHIP 1/16W R434 1-216-815-11 RES-CHIP 1/16W R317 1-216-833-11 RES-CHIP 1/16W R318 1-216-295-91 SHORT...
  • Page 87 DVP-F21 MB-99 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks R730 1-216-803-11 RES-CHIP 1/16W R1007 1-218-863-11 METAL CHIP 4.7K 0.5% 1/10W R731 1-216-295-91 SHORT R1008 1-218-863-11 METAL CHIP 4.7K 0.5% 1/10W R732 1-216-824-11 RES-CHIP 1.8K 1/16W R1009 1-218-863-11 METAL CHIP 4.7K...
  • Page 88 DVP-F21 MB-99 FL-123 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks RB107 1-233-576-11 RES, CHIP NETWORK 100 <COIL> <VARIABLE RESISTOR> L401 1-410-389-31 INDUCTOR 47UH L402 1-412-060-11 INDUCTOR 22UH RV501 1-223-583-11 RES, ADJ, CARBON 1K (VIDEO LEVEL) <INDICATOR> <VIBRATOR>...
  • Page 89 DVP-F21 FL-123 IR-39 Ref.No. Part No. Description Remarks Ref.No. Part No. Description Remarks <SWITCH> ACCESSORIES AND PACKING MATERIALS ********************************** S401 1-771-349-21 SWITCH, KEYBOARD (x) S402 1-771-349-21 SWITCH, KEYBOARD (B) X-3951-903-1 STAND ASSY (Silver) S403 1-771-349-21 SWITCH, KEYBOARD (A) X-3951-929-1 STAND ASSY (Black)
  • Page 90 DVP-F21 Sony Corporation 2001I0800-1 9-929-710-11 Home Video Campany © 2001. 9 – 116 – Published by Quality Assurance Dept.

Table of Contents