Advertisement
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
When using electrical appliances, basic
precautions should always be followed to
reduce the risk of fire, electrical shock and
injury to persons, including the following:
If the appliance is damaged, check with the
supplier before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings
of a bath, shower or swimming pool.
Do not locate the appliance immediately
below a fixed socket outlet or connection
box.
The appliance carries the Warning symbol
DO NOT COVER, indicating that it must not
be covered.
This appliance can be used by children
aged form 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by Children
without supervision.
Children of less than 3 years should be
kept away unless continuously supervised.
Children aged from 3 years and less than 8
years shall only switch on/off the appliance
provided that it has been placed or installed
in its intended normal operating position
and they have been given supervision or
instruction concerning use of the appliance
in a safe way and understanding the hazards
involved. Children aged from 3 years and
less than 8 years shall not plug in, regulate
and clean the appliance or perform user
maintenance.
Do not use this appliance in series with
a thermal control, a program controller, a
timer or any other device that switches on
the heat automatically, since a fire risk exists
when the appliance is accidentally covered
or displaced.
Ensure that furniture, curtains or other
combustible material are positioned no
closer than 1 metre from the appliance.
In the event of a fault unplug the appliance.
Unplug the appliance when not required for
long periods.
Although this appliance complies with safety
standards, we do not recommend its use on
deep pile carpets or on long hair type of rugs.
The appliance must be positioned so that
the plug is accessible.
If the supply cord is damaged it must be
replaced by the manufacturer or service
agent or a similarly qualified person in order
to avoid a hazard.
Keep the supply cord away from the front of
the appliance.
Warning: In order to avoid a hazard due to
inadvertent resetting of the thermal cut-out,
this appliance must not be supplied through
an external switching device, such as a timer,
or connected to a circuit that is regularly
switched on and off by the utility.
CAUTION - Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and
vulnerable people are present.
The heater carries the Warning symbol,
indicating that it must not be covered.
This instruction can be found at
WWW.VALOR.CO.UK
General
Unpack the electric suite carefully and retain the packaging for possible
future use, in the event of moving or returning the electric suite to your
supplier.
The fire incorporates a flame effect, which can be used with or without
heating, so that the comforting effect may be enjoyed at any time of the
year. Using the flame effect on its own only requires little electricity.
Before connecting the electric suite check that the supply voltage is the
same as that stated on the heater.
Please note: Used in an environment where background noise is very
low, it may be possible to hear a sound which is related to the operation
of the flame effect. This is normal and should not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This electric suite must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and operating
instructions.
Fixing - see Fig. 1&2
The electric suite should be securely fixed to a wall by the brackets supplied.
Also included with the suite is wall plugs and fixing screw to fit the suite to
the wall (Note: wall plugs supplied are only suitable for block walls, fixing
for stud walls are not included)
Locate the suite against the wall in the desired location and mark the wall
through the fixing brackets, remove the suite and drill the wall with a 6mm
diameter drill bit to a depth of 35mm.
Insert the wall plug and ensure the end of the wall plug is flush with the
surface of the wall.
Reposition the suite back into the desired position and line up the holes
on the fixing brackets with the holes on the wall plugs, when the suite is
positioned correctly insert the screws through the fixing bracket and into
the wall plug and tighten this can be done with a screw driver or with a
power tool. Ensure the suite is securly fitted on both sides of the suite.
UK
Continued
Advertisement
