, SeaTalk and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries. All other trademarks, trade names, or company names referenced herein are used for identification only and are the property of their respective owners.
It is the user’s responsibility to use official government charts, notices to mariners, caution and proper navigational skill when operating this or any other Raymarine Safety information product. Warning: Product installation and...
For optimum EMC performance we recommend that wherever Requirement for ferrites on non-Raymarine cables possible: If your Raymarine equipment is to be connected to other equipment • Raymarine equipment and cables connected to it are: using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit.
Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some Installation guide Raymarine products, we support its policy and ask you to be aware of how to dispose of this product. Information scope...
Class A transceiver, but is not mandatory aboard any vessel. Data Summary Classes of AIS Receiver Transceiver Transceiver The AIS350 is a receiver that receives messages from vessels, Data (receive) (transmit) (receive) land base stations, or aids to navigation (AToNs) carrying Class A Ship’s name...
Page 11
Class A systems Receiver Transceiver Transceiver Data (receive) (transmit) (receive) Ships Dynamic Conditions Reporting rate Time At anchor or moored 3 Minutes Ship’s position 0-14 knots 10 Seconds 0-14 knots and changing course Seconds 14-23 knots 6 Seconds Gyro heading Yes* 14-23 knots and changing course 2 seconds...
• 9600 baud rate. Used for Navtex. transmit and receive on a single physical bus at any one time, • 38400 baud rate. Used for AIS and other high speed applications. with each node being physically addressable. The standard AIS350 / AIS650 Installation instructions...
Page 13
• The 4800 baud wires connect to the appropriate points on the VHF radio or other NMEA0183 4800 baud input/output device. • The 38400 baud wires connect to appropriate Raymarine multifunction display. The NMEA0183 port on each display connected in this manner must be set to 38400 baud.
Drill cable and mounting holes. US B P WR/Da ta VHF ANT Make all connections to equipment. Secure all equipment in place. Complete the post-installation check. D12126-1 AIS350 system The following illustrations show examples of AIS350 systems. AIS350 / AIS650 Installation instructions...
Page 18
NMEA0183 at the same 2 m power/data cable time, as data conflicts could occur. Document pack contains: Pack contents • Installation instruction The AIS350 model contains the following items: • Support software CD-ROM • Warranty registration card SeaTalk Dust cap 1 m SeaTalk...
• Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run.
Ensure that all data cables are properly shielded that the cable shielding is intact (e.g. hasn’t been scraped off by being squeezed • Connecting power through a tight area). Note: With the USB cover open the unit will not be water resistant. AIS350 / AIS650 Installation instructions...
Note: The wire colors on your VHF may differ to that shown above, if this is the case then ensure you have connected the correct signals (e.g. IN - on the AIS connects to OUT - on your VHF and so on). AIS350 Receiver...
2. Identify the 38400 baud, NMEA0183 wires on your multifunction brown display. 3. Connect the wires as shown below. White IN + Orange and OUT + yellow Blue OUT – Orange and IN – green Brown IN + OUT + Orange and white AIS350 / AIS650 Installation instructions...
SeaTalk network as follows: i. Connect using SeaTalk 5–way connector. Fuse Fuse ii. Connect using a SeaTalk T-Piece connector. iii. Connect using a spare SeaTalk spur on a SeaTalk converter. AIS350 Receiver...
Page 24
• for runs of >1 m (3 ft), use 8 mm (#8 AWG) or greater. Grounding The following requirements apply when grounding Raymarine In any grounding system, always keep the length of connecting equipment which does not have a dedicated drain wire or shield: braid or wires as short as possible.
To reset the connection disconnect then reapply power to the AIS before closing and re-launching any PC applications using the USB connection. Finally, reconnect the USB cable between the PC and AIS unit. AIS350 Receiver...
50 mm (1.95 in) (130°F). 20.3 mm (0.8 in) 99.5 mm (3.92 in) 54 mm (2.12 in) Mounting Fitting the AIS unit Note: To ensure water resistance the unit must be mounted vertically with the connectors facing down. AIS350 / AIS650 Installation instructions...
3. Drill the mounting holes using a 3.2 mm (1/8”) drill bit. Using AIS 4. Part fit the screws. The exact method of using AIS depends on which type of Raymarine 5. Place the unit over the screws and move unit down to lock in multifunction display you are using.
● 129802 AIS broadcast safety • The VHF antenna lead is securely connected. message No vessel data At the relevant Raymarine multifunction display: ● 129041 AtoN position report • Place the cursor over the targeted vessel and ensure ● 129809...
Chapter 3: AIS650 Class B transceiver Chapter contents • 3.1 AIS650 Class B transceiver unit on page 32 • 3.2 Static data requirement on page 32 • 3.3 Requirements for USA & Canada on page 33 • 3.4 Requirements for areas outside of USA & Canada on page 36 •...
Mode and will not transmit. However, it will still operate as a receiver. Important: In the United States of America, the MMSI and Static Data must be entered only by a Raymarine dealer or other appropriately qualified installer of marine communications equipment on board vessels.The user is NOT authorized to do...
2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this equipment not expressly approved in writing by Raymarine Incorporated could violate compliance with FCC rules and void the operator’s authority to operate the equipment.
Page 34
A nine-digit Maritime Mobile Service Identity (MMSI) number is This Class B AIS digital apparatus complies with Canadian required to operate the AIS transceiver. ICES-003. Cet appareil numérique de la classe B AIS est conforme à la norme NMB-003 du Canada. AIS350 / AIS650 Installation instructions...
Page 35
• connected to the radio before transmitting otherwise input any inaccurate data in this device. The MMSI and Static Data must be entered only by a Raymarine dealer or • located where it will be away from people other appropriately qualified installer of marine communications •...
• located at least 1.5 metres (5 feet) from the radio’s main unit List of Countries In the European Union, your AIS transceiver may be used in the following countries: Austria Liechtenstein Belgium Lithuania Bulgaria Luxembourg Cyprus Malta Czech Republic Netherlands AIS350 / AIS650 Installation instructions...
3.5 Planning the installation AIS650 system The following illustrations show examples of AIS650 systems. Installation checklist Simple system example Installation includes the following activities: Installation Task Plan your installation. Obtain all required equipment and tools. Mount the system components. Route all cables. Drill cable and mounting holes.
Page 38
AIS 650 Cla s s B Tra ns ce ive r US B P WR/Da ta GP S ANT VHF ANT 12 V / 24 V SeaTalkng NM EA0183 - 4800 D12095-1 Item Description VHF Antenna VHF Radio VHF Splitter (Not supplied) AIS650 transceiver unit AIS350 / AIS650 Installation instructions...
Page 39
Pack contents Item Description The AIS650 model contains the following items: 4 x Fixing screws 2 x mounting studs 2 x thumbs nuts 2 m power/data cable Document pack containing: AIS 650 Cla s s B Tra ns ce ive r ta tus •...
• Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run.
3.7 Connections overview Always route data cables as far away as possible from: • other equipment and cables, The transceiver has the following connection types: • high current carrying ac and dc power lines, • antennae. Strain relief Ensure adequate strain relief is provided. Protect connectors from strain and ensure they will not pull out under extreme sea conditions.
If the GPS is not connected, the transceiver will operate in Silent Mode and an alarm message will be generated. You must acknowledge all alarm messages. The transceiver will not transmit, but will still receive. AIS350 / AIS650 Installation instructions...
3.9 VHF connection US B WR/Da ta GP S ANT VHF ANT Connect up your AIS unit to your vessel’s VHF connections by following the steps found under Connecting RF and Connecting NMEA0183 (low baud rate) below: Connecting RF 1. Connect a dedicated VHF antenna directly to the VHF antenna connector on your AIS unit, or 2.
2. Identify the 38400 baud, NMEA0183 wires on your multifunction brown display. 3. Connect the wires as shown below. White IN + Orange and OUT + yellow Blue OUT – Orange and IN – green Brown IN + OUT + Orange and white AIS350 / AIS650 Installation instructions...
3.11 AIS Silent mode connection Note: The wire colors on your Multifunction display may differ to that shown above if this is the case then ensure you have In addition to enabling AIS silent mode via a connected multifunction connected the correct signals (e.g. IN - on the AIS connects to display.
4. Ensure cables are adequately shielded. +VE bar -VE bar Where possible, connect individual items of equipment to individual circuit breakers. Where this not possible, use individual in-line fuses to provide the necessary protection. Circuit breaker Fuse Fuse AIS350 / AIS650 Installation instructions...
Page 47
• for runs of >1 m (3 ft), use 8 mm (#8 AWG) or greater. Grounding The following requirements apply when grounding Raymarine In any grounding system, always keep the length of connecting equipment which does not have a dedicated drain wire or shield: braid or wires as short as possible.
Note: When configuring static vessel data via USB you do not D12092-1 need to power up the AIS unit, the USB shall provide sufficient Item Wire color Description power to complete the data configuration. Power Supply + Black Power supply – AIS350 / AIS650 Installation instructions...
3.14 Installing proAIS2 and USB drivers 3.15 SD Card connection The AIS unit includes a multimedia card reader which allows Before connecting the AIS unit to a PC the proAIS2 application and connection of a SD card up to 2GB in size. USB drivers must be installed.
• If you intend surface mounting the antenna, ensure you have access to the underside of the mounting surface. • If you intend pole-mounting the antenna, the pole needs a 1 inch 14 TPI thread. AIS350 / AIS650 Installation instructions...
Page 51
Unit dimensions Important: The main requirement of the intended location for the GPS antenna is that it gives a good direct line of site to the entire sky, right around the horizon. Ensure that the intended mounting location is: • Open and clear of any obstructions (such as masts, search lights, or other structures) that could block line-of-sight to the sky.
Page 52
2. Using a pencil, offer up the unit and mark the location of the screw holes on the mounting surface. 3. Drill the mounting holes using a 3.2 mm (1/8”) drill bit. 4. Part fit the screws. AIS350 / AIS650 Installation instructions...
Page 53
remove these tabs before using the cable channel, you could Pole mounting damage the cable. If you want to pole-mount the GPS antenna, obtain a pole of suitable length with a 1 inch 14 TPI thread. Antenna Pole mount adaptor T op view Underside view 2.
This condition remains all the time the transceiver is operating normally and transmitting. Configuration Warning: Configure before use This Raymarine product must be correctly configured, to ensure optimum performance and minimize the chances of unsafe or other erroneous data. Configuration requirement After installation and successful switch on, the AIS transceiver must be configured for optimum performance aboard the vessel.
• Type Using AIS • GPS antenna position The exact method of using AIS depends on which type of Raymarine The manner in which configuration is carried out depends on the multifunction display you are using. legal requirements of the geographical area you are.
• The VHF antenna lead is securely connected. • The transceiver has not transmitted No vessel data At the relevant Raymarine multifunction display: for more than 2 reporting periods. This could be due to high AIS traffic • Place the cursor over the targeted vessel and ensure or loss of GPS fix.
Page 57
Status indicator Wait at least 30 minutes to check that a ’Quiet time’ has Title Transmit Receive remains amber not been requested by the local authority ● 129793 AIS UTC and Check that the: date report • GPS antenna is properly connected ●...
4.1 Raymarine customer support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and email. If you are unable to resolve a problem, please use any of these facilities to obtain additional help.
Chapter 5: Options and accessories Chapter contents • 5.1 SeaTalk cables and accessories on page 64 • 5.2 Spares and accessories on page 65 Options and accessories...
Page 65
5.2 Spares and accessories The following spares are available for the AIS receiver / transceiver: Part number Description R62241 GPS antenna — passive (with 10 m coaxial cable) — AIS650 only R32162 2 m power/Data cable Options and accessories...