Quadra-Fire 7100FP-GD-B Owner's Manual
  1. Manuals
  2. Brands
  3. Quadra-Fire Manuals
  4. Indoor Fireplace
  5. 7100FP-GD-B
  6. Owner's manual
Quadra-Fire 7100FP-GD-B Owner's Manual

Quadra-Fire 7100FP-GD-B Owner's Manual

Hide thumbs Also See for 7100FP-GD-B:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Installation Manual
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Model(s):
EPA CERTIFIED WOODBURNING
FIREPLACE
Installation and service of this
appliance should be performed by
qualified personnel. Hearth & Home
Technologies recommends HHT
Factory Trained or NFI certified
professionals.
Owner's Manual

Care and Operation

R
O-T L
Portland
Tested and
Oregon USA
Listed by
C
US
OMNI-Test Laboratories, Inc.
Quadra-Fire • 7100 FP Owner's Manual • 433-3600 • Rev J • 09/21/15
Pour demander un exemplaire en
français de ce Manuel
du propriétaire, visitez www.quadra-
fire.com/translations.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• DO NOT overfire. Overfiring will void your
warranty.
• Comply with all minimum clearances to com-
bustibles as specified. Failure to comply may
cause house fire.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
WARNING
Fire Risk.
For use with solid wood fuel only.
Other fuels may overfire and generate
poisonous gases (i.e. carbon monoxide).
1

Advertisement

Table of Contents
loading

Related Manuals for Quadra-Fire 7100FP-GD-B

Summary of Contents for Quadra-Fire 7100FP-GD-B

  • Page 1: Care And Operation

    Technologies recommends HHT Factory Trained or NFI certified For use with solid wood fuel only. professionals. Other fuels may overfire and generate poisonous gases (i.e. carbon monoxide). Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 2: Table Of Contents

    3. Seasoning B. Contact Information 4. Storing Wood 5. Burning Process 6. Dirty Glass 7. Creosote Formation 8. Opacity D. First Fire E. Lighting Instructions F. Heat Management Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 3: Welcome

    U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to comply with 2015 particulate emission standards. Not approved for sale after May 15, 2020. This wood heater was found to have an average emissions rate of 3.1g/hr using method 5H. 433-1400 Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 4: Limited Lifetime Warranty

    Firebox and heat exchanger Lifetime All replacement parts 90 Days beyond warranty period See conditions, exclusions, and limitations on next page. 4021-645G 2/15 Page 1 of 2 Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 5 THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EXPRESSED WARRANTY SPECIFIED ABOVE. 4021-645G 2/15 Page 2 of 2 Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 6: Btu & Efficiency Specifications

    Quadra-Fire is a registered trademark of Hearth & Home Technologies. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 7: Important Safety And Operating Information

    Trim 48 in. (1219 mm) Clear Space Front of Fireplace 12 in. (305 mm) Clear Space Sides of Fireplace (from the FP opening) Figure 3.1 Clear Space Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 8: Firebrick

    WARNING! Risk of Fire! A chimney fire can perma- specifications can result in permanent damage to the nently damage your chimney system. Failure to re- fireplace. place damaged components and make proper repairs can cause a structure fire. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 9: General Operating Parts

    Automatic Combustion Air Control Handle Auxiliary Convection ACC Override Outside Air Control Handle Air Lever Lever (Must be open during use) Figure 3.3 General Operating Parts Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 10: Automatic Combustion Control (Acc)

    ACC Override Control Left - Close Figure 3.5 ACC Override Control Automatic Combustion Control (ACC) Left - Close (low) Right-Open (high) Figure 3.4 Automatic Combustion Control (ACC) Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 11: Auxiliary Convection Air System

    Outside Air Control Handle Clockwise Counterclockwise Open Close Figure 3.7 Outside Air Control Handle Auxillary Convection Air Lever Control Left - Close Right-Open Figure 3.6 Auxillary Convection Air Lever Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 12: Glass Doors

    Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 13: Hardwood Vs. Softwood

    Air dry to a moisture content of around 20% • Alder - Soft wood - about nine months - Hard wood - about eighteen months NOTICE: Seasoning time may vary depending on drying conditions. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 14: Storing Wood

    The coals burn with hot blue flames. It is very important to reload your fireplace while enough lively hot coals remain in order to rekindle the next load of wood. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 15: First Fire

    Break up any large chunks and distribute the coals so new wood is laid evenly on hot coals. Add desired amount of fuel, close the door. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 16: Maintenance And Service

    NFPA Level III inspection criteria. WARNING! Risk of Asphyxiation and Fire! Annual inspection by qualified technician recommended. Check: • condition of doors, surrounds and fronts • condition of glass and glass assembly • obstructions of combustion and ventilation air • obstructions of termination cap Clean: • glass • air passageways, grilles Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 17: Creosote (Chimney) Cleaning

    Termination Caps Remove 2 screws from the front and back and lift the top off. TCT375 Terra Cotta Termination Cap Figure 4.1 Chimney & Termina- tion Cap Cleaning Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 18: Care And Cleaning Of Plated Surfaces

    It may be necessary to adjust or tighten the door latch. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 19: Replacement Maintenance

    Replace the door on the fireplace. • After the first burn, recheck the tightness of the screws. NOTICE: Remove all labels from glass before lighting the first fire in your fireplace. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 20: Firebrick Replacement

    1 9” x 3-1/4” x 1-1/4” Angled (see drawing) 2 6-1/4” x 4-1/2” x 1-1/4” 3-1/4" 1-1/4" 3 9” x 2” x 1-1/4” 4 6-1/4” x 3-1/2” x 1-1/4” 5 9” x 4.5” x 1-1/4” Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 21: Baffle Removal And Installation

    To install the fiber board baffle, repeat the 2nd through 4th steps in reverse. Be sure the fiber board baffle and ceramic blanket are pushed back fully and the blanket is down and flat. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 22: Timer Assembly Replacement

    Air Chamber Cover is attached to Timer Assembly Figure 4.13 Timer Assembly with Air Chamber Cover Figure 4.10 Installing Fans (Linkage arm is not included in the kit) Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 23 See Figure 4.18. 4.18. Timer Plate Air Chamber Cover Attach with 1/4-20 bolts Figure 4.16 Remove Screws from Timer Mounting Plate Figure 4.19 Install Control Box Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 24: Timer Removal & Replacement

    Note that the D cut is now facing the linkage timer arm. Re-attach the linkage timer arm, Figure 4.23. • Retun to Timer Assembly Replacement, Section 4.B.6. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 25 Screw 8-32 x 1/2 PH PHL TC Linkage Timer Arm Attachment Nut & Set Screw Screw 6-32 x 1/4 PH PHL TC Mounting Bracket Timer, Mechanical, 12 hours Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 26: Troubleshooting

    Be sure you have air available for combustion and that your firewood is dry and well seasoned. Build your fires properly and according to the instructions given in op- Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 27 Air register from furnace near fireplace? Doors opening and closing? Outside air Window closed Combustion closed? for start-up? air control Figure 5.1 Factory-built Fireplaces: Troubleshooting Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 28: Troubleshooting Table

    • Insufficient fuel for fire/heat required Fan doesn’t come on • No power • Fireplace is not hot enough to activate snap disc • Snap disc may be faulty Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 29: Reference Materials

    7100FP-BK-B, 7100FP-GD-B, and 7100FP-NL-B (Aug 2006 - Active) 7100FP-BK, 7100FP-GD and 7100FP-NL (Mar 2005 -- July 2006) MISSION HILL FASCIA VALLEY FORGE FASCIA Part number list on following page. 09/15 Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 30: Service Parts

    DF-7100VF Fascia, Valley Forge DF-7100VF-B Post 0071580458 Post 0071580458 DF-7100RM Fascia, Rolling Meadows DF-7100RM-NL Post 0071580458 Component Pack 433-5990 Additional service part numbers appear on following page. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 31: Door Handle Assembly

    834-2590 Screw, Flat Head Philips 8-32 x 1/2 Pkg of 10 832-0860 Washer, Sae, 3/8 Pkg of 3 832-0990 Additional service part numbers appear on following page. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 32: Side View

    Light Switch 480-1260 Light Switch Cover Plate 480-1270 Outside Air Hood 6” 4059-051 Paint Touch-Up 812-0910 Unit Collar 659-125 Additional service part numbers appear on following page. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 33 Pkg of 40 12460/40 Pkg of 24 226-0160/24 Wing Nut WF .8-32, Refractory Retainer Wing Nut WF .1/4-20, for use with fan kits Pkg of 12 226-0110/12 Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 34 This page intentionally left blank. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...
  • Page 35 This page intentionally left blank. Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

  • Page 36: Contact Information

    6769426, 6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884,7047962, 7216645, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending. Printed in U.S.A. - Copyright 2012 Quadra-Fire • 7100 FP Owner’s Manual • 433-3600 • Rev J • 09/21/15...

This manual is also suitable for:

7100fp-nl-b

Table of Contents