Advertisement
A single-phase,
60-Hz, AC-only,
electrical
supply is required
on a
separate
circuit.
A 15amp
time-
delay fuse or circuit
breaker
is
required
Copper
wire (#14
gauge)
is required.
The fuse size
must not exceed
the circuit
rating
specified
on the model
and serial
label. The model
and serial label is
located
behind
the front panel on
the base flange.
Specific
electrical
requirements
are listed in the chart. Follow the
requirements
for the type of plug
on the power supply cord.
W&g
requirements
Plug Type A
Plug Type B
;$f%g
P
Lb
W" blade
receotacls
0
'J
3-pron
fJou"cf"g-
ype wall
receptacle.
grouncllng
prow
power supply cord
groundlng prong
115volt
-
230/208-volt
-
103%
min.,
197.6~ min.,
126.5~ max.
253~
max.
7.5-amp
12-amp rating
rating or less
or less - use a
- a double
single outlet
outlet is
and a sep-
acceptable.
orate circuit.
7.6- through
12- through
16-
12-amp ratings
amp ratings -
- use only a
use only a
jingle outlet
single outlet
and separate
and a sep-
Zircuit.
orate circuit.
Exordmended
grounding
For your personal
safety, this
appliance
must be grounded.
This appliance
is equipped
with a
power
supply cord having
a
3-prong
grounding
plug. To
minimize
possible shock hazard,
the cord must be plugged
into a
mating,
3-prong
grounding-type
wall receptacle,
grounded
in
accordance
with the National
Electrical
Code, ANSVNFPA 70 -
latest edition*,
and all local codes
and ordinances.
If a mating
wall
receptacle
is not available,
it is the
personal
responsibility
and
obligation
of the customer
to have
a properly
grounded,
3-prong
wall
receptacle
installed
by a qualified
electrician.
Now start...
With air conditioner
in room where
it will be installed.
I
THROUGH-THE-WALL
INSTALLATION INSTRUCTIONS.
It is the customer's
responsibility
and obligation
to have this
product
installed
by a qualified
technician
familiar with through-
the-wall
room air conditioner
installations.
appropriate
header
if required
\
Pl
ss
Frame
Construction
appropriate
header
if required,
lintel
I
alternate
construction
for plaster
-
'
Brick Veneer
to frame.
Construction
1
When using a wood,
n
metal or plastic molding,
the finish frame should line up with
inside wall. If the plastered
wall is
to be flush with the cabinet
and
no molding
is used, the finish
frame must be set l/2 inch into
the wall.
hi
wall opening
w t
24-718"
2,
-I
Dimension
Cut opening
depends
on wall
through
the wall.
thickness
and
Remove
insulation.
type of molding.
3
Use 1 -inch or heavier
lumber for wood
frame.
n
Measure
depth
of wall
opening
and frame. Apply wood
preservative
to the outside
exposed
surface.
4
Insert the frame in the wall
opening.
Square and level
n
frame. Nail frame securely
to the wall studs.
5
Remove air conditioner
and
n
front panel from carton.
6
If you plan to install a drain
hose to the back of the air
1 condiiioner,
install the drain
hose connector
as follows:
1, Remove
the drain hose
connector,
gasket and screws
from the plastic bag.
2. Attach
them on the back of the
air conditioner
as shown above.
Note: If you are installing
a new
unit into an existing sleeve, you
may need to modify the sleeve for
the drain connector.
Page 3
Advertisement
