Sign In
Upload
Manuals
Brands
Dürkopp Adler Manuals
Sewing Machine
806N-111-10
Dürkopp Adler 806N-111-10 Manuals
Manuals and User Guides for Dürkopp Adler 806N-111-10. We have
1
Dürkopp Adler 806N-111-10 manual available for free PDF download: Service Instructions Manual
Dürkopp Adler 806N-111-10 Service Instructions Manual (212 pages)
Brand:
Dürkopp Adler
| Category:
Sewing Machine
| Size: 45.47 MB
Table of Contents
Table of Contents
3
About These Instructions
7
For Whom Are These Instructions Intended
7
Representation Conventions - Symbols and Characters
7
Other Documents
8
Liability
9
Safety
11
Basic Safety Instructions
11
Signal Words and Symbols Used in Warnings
13
Basic Setting
17
Removing/Mounting Covers
17
Removing the Covers
17
Assembling the Covers
20
Machine Head 111
23
Stitch Regulator and Transmission Lever
25
Setting the Zero Position of the Stitch Regulator
25
Rocker and Throat Plate
26
Setting the Position of the Rocker
26
Timing the Rocker Oscillation (Zigzag)
30
Setting the Range of the Rocker Oscillation (Zigzag Stitch Width)
32
Setting the Horizontal Position of the Throat Plate
33
Setting the Height of the Throat Plate
34
Setting the Winder
35
Hook, Needle Bar, Needle Guard, and Needle Guide
36
Setting the Loop Stroke
36
Re-Engaging the Friction Clutch
38
Setting the Needle Bar Height
39
Setting the Distance between Hook and Needle
40
Setting the Position of the Needle Guide
43
Bobbin Capsule Lifter
44
Setting the Amount of Finger Travel
45
Setting the Size of the Lifting Gap (Position of Finger Travel)
46
Timing the Bobbin Capsule Lifting
47
Sewing Foot
48
Timing the Sewing Foot Movement
48
Setting the Thread Tensioning Spring
49
Setting the Thread Tension Lift
51
Setting the Thread Advancing Device
52
Machine Arm
53
Setting the Lower Position of the Machine Arm
54
Setting the Speed Lift/Lower Sewing Head
55
Setting the End Position Damping of the Cylinder
56
Thread Cutter
57
Checking the Function Sequence
57
Setting the Lateral Position of the Thread-Pulling Knife
58
Setting the Height of the Thread-Pulling Knife
59
Setting the Position of the Counter Blade in Relation to the Thread-Pulling Knife
60
Setting the Position of the Hook Thread Clamp
61
Setting the Control Cam Position
63
Setting the Swivel Range of the Thread-Pulling Knife
64
Setting the Position of the Roller Lever in Relation to the Control Cam
65
Machine Head 121
67
Adjustment Aids
69
Gage Set
69
Integrated Adjusting Disk
70
Setting the Position of the Integrated Adjusting Disk Relative to the Arm Shaft
71
Setting the Sewing Foot Height
73
Setting the Needle Thread Tension Release
75
Setting the Thread Tensioning Spring
76
Setting the Needle Thread Regulator
77
Winder
78
Setting the Winder
78
Canceling Cylindrical Winding
79
Exchanging the Friction Ring
80
Resetting the Winder Wheel
81
Setting the Needle Bar Height
82
Hook Settings
83
Setting the Loop Stroke and Hook Tip Distance to the Needle
83
Aligning the Hook Drive Housing
84
Aligning the Bobbin Case Support
86
Setting the Throat Plate
87
Setting the Needle Guard
89
Thread Cutter
90
Setting the Control Cam for Timing the Knife Movement
91
Setting the Position of the Stationary Knife
92
Regrinding the Stationary Knife
93
Installing the Thread Guide Plate
94
Setting the Thread-Pulling Knife
95
Setting the Cutting Pressure
97
Replacing the Right Arm Shaft Bearing
98
Machine Arm Position
100
Setting the Lower Position of the Machine Arm
100
Setting the Speed of the Machine Arm
101
Setting the End Position Damping of the Cylinder
102
Stacker
103
Rotating the Stacker Tray
104
Lateral Position of Outfeed Roller and Stacker
104
Setting the Lateral Outfeed Roller Position
105
Setting the Lateral Stacker Position
106
Outfeed Roller
107
Setting the Lower Outfeed Roller Position
107
Setting the Movement of the Ejection Rollers
108
Setting the Position of the Open Inner Shackle
109
Setting the Movement of Outer and Inner Shackle and of the Tray
110
Setting the Sensitivity of the Light Barrier
112
Setting the Air Nozzle
113
Edge Folding Device
115
Outer Frame
115
Setting the Actuating Time of the Outer Frame Switch
115
Setting the Adjusting Wheels on the Inner Frame
116
Functionality of the Adjusting Wheels
117
Setting the Adjustment Range of the Front Adjusting Wheel
118
Setting the Adjustment Range of the Rear Adjusting Wheel
119
Middle Slide
120
Setting the Basic Height of the Middle Slide
121
Setting the Basic Height of the Middle Slide Relative to the Outer Frame
122
Setting the Alignment Position of the Middle Slide
123
Setting the Movement of the Middle Slide
124
Setting the Actuating Time of the Middle Slide Switches
125
Setting the Distance of Lateral and Front Slides
127
Corner Tucker
128
Setting the Position of the Swung-In Corner Tucker
129
Setting the Height of the Corner Tucker
131
Adjusting the Proximity Switch for the End Position
132
Transfer Carriage
135
Aligning the Transfer Plate
135
Calibrating the Positions
136
Reading the Coding
138
Calibrating the Top Sewing Position
139
Calibrating the Position of the Edge Folding Station
141
Setting the Light Barrier for Reading the Transfer Plate Coding
141
Service Settings Via Software
143
Operating Software Version
143
Access to the User Interface Intended for Technicians
144
Calling up the Start Screen of the User Interface Intended for Technicians
144
Calling up the User Interface Intended for Technicians from
144
User Interface 2
144
Structure of the User Interface Intended for Technicians
145
Setting Options on the User Interface Intended for Technicians
145
Selecting the Language
146
Setting the Speed of the Transfer Plate
146
Setting the Outfeed Roller Speed
147
Launching DA-CAD
148
Copying Files to the PC
150
Viewing the File Directory and Deleting Files
151
Measuring the End Positions of the Transfer Carriage
153
Calibrating the Positions
153
Checking and Setting the Sewing Motor
156
Test Roll-Off Device
159
Check Output-Input
161
Showing the Information List
166
Exiting the User Interface Intended for Technicians
167
Maintenance
169
Cleaning
169
Lubricating (806N-121-10)
171
Lubricating (806N-111-10)
173
Servicing the Transfer Carriage
175
Lubricating the Spherical Bush of the Torque Shaft
175
Lubricating the Carriage of the Linear Rails
176
Lubricating the Spherical Heads
177
Servicing the Pneumatic System
177
Parts List
179
Disposal
181
Troubleshooting
183
Customer Service
183
Messages of the Software
183
Technical Data
187
Requirements for Fault-Free Operation
187
Appendix
189
Advertisement
Advertisement
Related Products
Dürkopp Adler 806N-111
Dürkopp Adler 806N-121
Dürkopp Adler 806N-121-10
Dürkopp Adler 827
Dürkopp Adler 867
Dürkopp Adler 878-M PREMIUM
Dürkopp Adler 847201
Dürkopp Adler 847-75-66
Dürkopp Adler 838-270522-M
Dürkopp Adler 884
Dürkopp Adler Categories
Sewing Machine
Industrial Equipment
Controller
More Dürkopp Adler Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL