Table of Contents
Advertisement
coffee buttons (
Once the coffee has been made, the appliance is ready to be
used again.
Please note!
•
Various alarm messages could be displayed while using
the machine (FILL TANK, EMPTY GROUNDS CONTAINER,
etc.). Their meaning is explained in the section "Displayed
messages" (page 21).
•
For hotter coffee, see the section "Tips for a hotter coffee"
(page 13).
•
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in the "Trouble-
shooting" section on page 22.
Making coffee using pre-ground coffee
Important!
•
Never add pre-ground coffee when the machine is off or it
could spread through the inside of the machine and dirty
it. This could damage the appliance.
•
Never use more than one level measure as it could dirty
the inside of the machine or block the funnel.
Please note!
If you use pre-ground coffee, you can only make one cup
of coffee at a time.
1. Press the
button (fig. 10) until "Pre-ground" is
displayed.
2. Open the beans container lid, then open and raise the pre-
ground coffee funnel lid.
3. Make sure the funnel is not blocked, then add one level
measure of pre-ground coffee (fig. 18).
4. Place a cup under the coffee spouts.
5. Press the 1 cup button
6. Preparation begins. The amount of coffee selected is dis-
played together with a progress bar which gradually fills
as preparation progresses.
Please note!
If "Energy saving" mode is active, you may have to wait a few
seconds before the first coffee is delivered.
MAKinG MiLK BAsED DrinKs
Please note!
•
To avoid producing milk with poor froth or large bubbles,
always clean the milk container lid and hot water nozzle
as described in the section "Cleaning the milk container"
on pages 15 and 18.
or
).
(fig. 15).
Filling and attaching the milk container
1. Remove the lid by pressing the release button C4 and at
the same time lifting the lid upwards (fig. 19);
2. Fill the milk container with a sufficient quantity of milk,
not exceeding the MAX level marked on the container (fig.
20). Each mark on the side of the container corresponds
to about 100 ml of milk.
Please note!
•
For a denser more even froth, you must use skimmed or
partially skimmed milk at refrigerator temperature (about
5°C).
•
If "Energy saving" mode is enabled, you may have to wait
a few seconds before the drink is delivered.
3. Make sure the milk intake tube is correctly inserted in the
bottom of the milk container lid (fig. 21).
4. Replace the lid on the milk container and press down-
wards until it clicks in place.
5. Extract the hot water spout by pressing the button on the
spout (fig. 22A)
6. Attach the milk container to the nozzle and push as far as
it will go (fig. 23). The machine emits a beep (if the beep
function is enabled).
7. Place a sufficiently large cup under the coffee and frothed
milk spouts. Adjust the length of the milk spout. To move
it nearer the cup, simply pull it downwards (fig. 24).
8. Follow the instructions below for each function.
Adjusting the amount of froth
Turn the froth adjustment dial to adjust the amount of froth
on the milk delivered while making cappuccino and milk based
coffees.
Dial
Description
position
No froth
Min. froth
Max. froth
Making milk based drinks automatically
The CAFFELATTE, CAPPUCCINO, MACCHIATO and MILK buttons
on the control panel enable these drinks to be prepared auto-
matically. Proceed as follows:
1. Fill the milk container and attach it as described above.
2. Turn the froth adjustment dial on the milk container lid to
the position corresponding to the required froth.
13
Recommended for...
CAFFELATTE/
MILK (hot milk)
LATTE MACCHIATO
CAPPUCCINO/
MILK (frothed milk)
Advertisement
Table of Contents
Troubleshooting
