Advanced Connecting; Connecting The Remote Control Jacks - Marantz SR7001 User Manual

ADVANCED CONNECTING

UT 1(TV) INPUT 2(DVD)
DVD Audio player
or
Super Audio CD
C B / C R / Y C B / C R /
P B P R P B P R
Multi channel player
UT 3(VCR1) INPUT 4(DSS/VCR2)
T 4(DSS/VCR2) OUTPUT 1 OUTPUT 2
MULTI TV(1) DVD(2) VCR1(3)
OUT
IN OUT
DC OUT
1 1
N
IR
CENTER FLASHER RECEIVER
IN IN
2 2
L
EMITTER
UT
OUT
E CD/CDR MULTI OUT
R
L L
FRONT SURR. SURR. SUB
BACK WOOFER
R R
OUT IN OUT A B
O
R L R L R L
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page25.
R L R L R L
R L R L R L
OUT
MODEL NO
PUT
1
RS-232C
OUT
Y C B / C R / PUT
P B P R
2
HDMI
Ver1.2
L
XM XM
AC
DSS/VCR2(4) MONI. OUT
R
FRONT SURR. SURR.
S-VIDEO
IN OUT BACK
L L L SL SL SL SBL SBL SBL C C C
PRE PRE PRE
Power
OUT OUT OUT
Amplifer
R R R SR SR SR SBR SBR SBR SW SW SW
L L L SL SL SL SBL SBL SBL C C C
Subwoofer
7.1CH 7.1CH 7.1CH
IN IN IN
R R R SR SR SR SBR SBR SBR SW SW SW
( ( AUX2 (AUX2) AUX2) )
L R L R L R
Front
Center
Left
Surround
Left
Surround
Back Left
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.

CONNECTING THE REMOTE CONTROL JACKS

FM (75Ω) ANTENNA
GND AM
COMPONENT
VIDEO
INPUT 1(TV) INPUT 2(DVD)
TV(1) DVD(2) VCR1(3) DSS/VCR2(4)
VIDEO
IN OUT IN
DIGITAL IN DIGITAL OUT
4 5 6 COAX.
CENTER
1 2 3 OPT.
TV DVD VCR1 DSS/VCR2
L
SUB
WOOFER
R
IN OUT IN
CD recorder
REMOTE
CONTROL
IN
Front
OUT
Right
EXTERNAL INTERNAL
Surround
Right
Surround
Back Right
q
You can control other Marantz products through the
SR7001 with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on the SR7001. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the SR7001. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er's, power
switch is synchronized with this unit's power switch.
Set the REMOTE CONTROL SWITCH on the other
units, (not the SR7001) to "EXT." (external) to use
this feature.
INPUT 1(TV) INPUT 2(DVD)
OU
PU
1
OU
C B / C R / C B / C R / C B / C R /
Y P P Y P P Y P P PU
B R B R B R
2
INPUT 3(VCR1) INPUT 4(DSS/VCR2)
INPUT 3(VCR1) INPUT 4(DSS/VCR2) OUTPUT 1 OUTPUT 2
HDMI
Ver1.2
MONITOR MULTI TV(1) DVD(2) VCR1(3) DSS/VCR2(4) MONI. OUT
OUT OUT
2
IN OUT IN OUT S-VID
OUT
RC-5 MULTI RC RC-5 RC-5 DC OUT
L SL SBL
IN IN IN 1 1
IR
FLASHER RECEIVER
IN IN
2 2
OUT OUT OUT EMITTER
OUT R SR SBR S
TAPE CD/CDR MULTI OUT L SL SBL
OUT IN OUT IN OUT A B R SR SBR S
(AUX2)
AUDIO
1
DVD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar devices
are connected to RC-5 IN of the SR7001, be sure to
always disable operation of the infrared sensor on the
main unit by using the following procedure.
1.
Hold down the MULTI button and the MENU
button on the front panel at the same time for
fi ve seconds.
2.
The setting "IR=ENABLE" is shown on the FL
DISPLAY.
3.
Press the CURSOR buttons (1, 2) to change
this to "IR=DISABLE".
4.
Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
• Be sure to set to "IR=ENABLE" when external
infrared sensors or similar devices are not connected.
Otherwise, the main unit will be unable to receive
remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to "IR=ENABLE".
RC OUT
OPTION
CD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
17