Advanced Connecting; Connecting The Remote Control Jacks - Marantz SR4500 User Manual

ADVANCED CONNECTING

R L R L
L R
CENTER
L
R
FRONT SURR. SUB SURR.
WOOFER BACK
POWER
AMPLIFER
Subwoofer
Front
Front
Center
Right
Left
Surround Surround
Left Right
Surround
Surround
Back Left
Back Right
R
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a SACD multichannel player, DVD
audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the 7.1
channel input level menu. See page 29.
14
SR4500U DFU_01_ENG 1_2 Page 14
R L R L L R
VIDEO S
V
FM (75Ω) GND AM IN OUT
IN OUT IN OUT MONITOR VCR1 DVD MONITOR
ANTENNA DSS / VCR2 VCR1 DVD TV
L L SL SL C C SBL SBL
L
R
IN OUT IN OUT IN OUT IN OUT R R SR SR SW SW SBR SBR 1
CD TAPE CDR/MD DSS / VCR2 VCR1 DVD TV 7.1CH INPUT 7.1CH INPUT
AUDIO
AUDIO AUDIO
PRE OUT PRE OUT
L L SL SL C C SBL SBL
R L R L R L
FRONT SURROUND BACK SURROUND CENTER
R R SR SR SW SW SBR SBR S. SPEAKER B
SPEAKER SYSTEMS MINIMUM 6 OHMS
L R R L R L
L R L R L R
CENTER
L
SUB SURR.
FRONT SURR.
WOOFER BACK
DVD AUDIO PLAYER
or
SACD MULTI CHANNEL PLAYER
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.

CONNECTING THE REMOTE CONTROL JACKS

RC-5 RC-5
S- COMPONENT VIDEO
VIDEO
Y
IN OUT
MONITOR VCR1 DVD MONITOR IN IN OUT OUT
TV L SL C SBL
C
B / P B
C R /
P R
R SR SW SBR 1 2 OPT. 3 4 COAX.
TV 7.1CH INPUT OUT OUT DVD DSS / VCR 2 MONITOR
DIGITAL
UNSWITCHED
1A 120W MAX
R L R L
RROUND BACK SURROUND CENTER SWITCHED
. SPEAKER B 1A 120W MAX
NIMUM 6 OHMS AC OUTLETS
120V 60HZ
1
CD RECORDER
REMOTE REMOTE
CONTROL CONTROL
IN IN
OUT OUT
EXTERNAL INTERNAL EXTERNAL INTERNAL
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then the
signal is sent to the connected device through this
terminal. Therefore you only need to aim the remote
at one unit. Also, if a Marantz power amplifier (some
models excluded) is connected to one of these
terminals, the power amplifier's, power switch is
synchronized with this unit's power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for
this feature.
04.6.25, 11:29 AM Adobe PageMaker 6.5J/PPC
2
RC OUT
AC IN
OPTION
MD DECK
CD PLAYER
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR4500,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1.
Hold down the 7.1CH INPUT button and
MENU button on the front panel at the same
time for five seconds.
2.
The setting "IR=ENABLE" is shown on the FL
DISPLAY.
3.
Press the or cursor button to change this
to "IR=DISABLE".
4.
Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
Be sure to set to "IR=ENABLE" when external
infrared sensors or similar devices are not
connected. Otherwise, the main unit will be
unable to receive remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to "IR=ENABLE".