Marantz SR8001 Service Manual
  1. Manuals
  2. Brands
  3. Marantz Manuals
  4. Stereo Receiver
  5. SR-8001
  6. Service manual

Marantz SR8001 Service Manual

Hide thumbs Also See for SR8001:
Table of Contents

Advertisement

Quick Links

Service
Manual
STANDBY
POWER ON/STANDBY
SECTION
1. TECHNICAL SPECIFICATIONS ........................................................................................... 1
2. TECHNICAL DESCRIPTION ............................................................................................... 4
3. POWER AMPLIFIER ADJUSTMENT .................................................................................. 9
4. SERVICE MODE ................................................................................................................ 10
5. SYSTEM ERROR .............................................................................................................. 12
6. UPDATE FIRMWARE ......................................................................................................... 14
[B] WRITING AND UPDATE SOFTWARE .......................................................................... 39
Mode 2: Update/Download DSP's software to 8M Flash-ROM ...................................... 45
7. WIRING DIAGRAM ............................................................................................................ 61
8. BLOCK DIAGRAM ............................................................................................................. 63
9. SCHEMATIC DIAGRAM ..................................................................................................... 67
10. PARTS LOCATION ............................................................................................................. 97
11. EXPLODED VIEW AND PARTS LIST .............................................................................. 131
12. MICROPROCESSOR AND IC DATA ................................................................................ 137
13. ELECTRICAL PARTS LIST .............................................................................................. 175
14. ABOUT REPLACE THE MICROPROCESSOR WITH A NEW ONE ............................. 242
Please use this service manual with referring to the user guide ( D.F.U. ) without fail.
AV SURROUND RECEIVER SR8001
INPUT SELECTOR
PURE DIRECT
DISP
MULTI
AUTO
TUNED
SLEEP
AUTO
SURR
DIRECT
DSD
SURROUND
MULTI
MODE
AUTO
MULTI
SPEAKER
7.1CH INPUT
PURE DIRECT
THX
MENU
PHONES

TABLE OF CONTENTS

SR8001
SR8001 /
AV Surround Receiver
/U Only
SURROUND
ST
SPKR A B
V-OFF
PEAK
ATT
ANALOG
DIGITAL
DIGITAL
DISC 6.1
MT X 6.1
NIGHT
EQ
L
C
R
LFE
AAC
PCM
SL
S
SR
DOWN
BAND
T-MODE
MEMORY
CLEAR
DISPLAY
SPEAKERS
MultEQ
A/B
ENTER
EXIT
DIGITAL
MIC
N1B/N1G/N1S/U1B
READY
VOLUME
UP
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
PAGE
Part no. 90M06CW855010
First Issue 2006.08
MZ

Advertisement

Table of Contents
loading

Related Manuals for Marantz SR8001

Summary of Contents for Marantz SR8001

  • Page 1: Table Of Contents

    Service SR8001 / N1B/N1G/N1S/U1B Manual AV Surround Receiver /U Only AV SURROUND RECEIVER SR8001 READY INPUT SELECTOR VOLUME PURE DIRECT SURROUND DISP MULTI AUTO TUNED SPKR A B V-OFF PEAK ANALOG DIGITAL DIGITAL SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1...
  • Page 2 MARANTZ Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed.

  • Page 3: Technical Specifications

    Remote Control Unit RC8001SR ..........1 AAA-size batteries ............... 2 Microphone ................1 FM Antenna ................1 AM Loop Antenna ..............1 Front AUX Jack Cover ............1 AC cable ................1 17-5/16 ins. (440 mm) AV SURROUND RECEIVER SR8001 READY INPUT SELECTOR VOLUME PURE DIRECT DISP MULTI AUTO...
  • Page 4 The relation between the selected surround mode and the input signal The surround mode is selected with the surround mode buttons on SR7001/SR8001 or the remote control unit. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That relationship is as follows;...
  • Page 5 Output Channel Front information display Surround Mode Input Signal Decoding SubW Signal format indicators Channel status 2 DIGITAL EX Dolby Virtual Dolby Surr.EX Dolby Virtual Speaker L, C, R, SL, SR, S, LFE 2 DIGITAL Speaker Dolby D (5.1ch) Dolby Virtual Speaker L, C, R, SL, SR, LFE 2 DIGITAL Dolby D (2ch)

  • Page 6: Technical Description

    Only receiver and controller products bearing the The Marantz SR7001 was required to pass a rigorous THX Surround EX logo, when in the THX Surround series of quality and performance tests, in addition to...
  • Page 7 THX Select2 Neo:6 offers several important improvements as Before any home theater component can be THX follow, • Neo:6 provides up to six full-band channels of Select2 certifi ed, it must pass a rigorous series of matrix decoding from stereo matrix material. Users quality and performance tests.
  • Page 8 When DVD-video appeared, it became possible to Dolby Digital EX creates six full-bandwidth output deliver 24-bit, 96 kHz audio into the home, but only in channels from 5.1-channel sources. This is done two channels, and with serious limitations on picture. using a matrix decoder that derives three surround This capability has had little use.
  • Page 9 Dolby Virtual Speaker is a technologycertified HDCD ® (High Defi nition Compatible Digital ® ) is a by Dolby Laboratories that creates a virtualized patented process for delivering on Compact Disc the surround sound experience from two speakers using full richness and details of the original microphone a multichannel Dolby Digital source.
  • Page 10 of-phase relative to the others. It measures the distance to each loudspeaker from the main listening position and adjusts the delays so that sound from There are several factors that can degrade the sound each loudspeaker arrives at the same time. Finally, from even the best loudspeakers in a listening room.

  • Page 11: Power Amplifier Adjustment

    3. POWER AMPLIFIER ADJUSTMENT Idling Current Alignment アイドリング電流調整 Each of the measurement points are provided with the 電源を する前にそれぞれの "+" 端子と "-" 端子間にデ two test points. Set a digital Voltage meter to DC voltage ジタルボルトメーターを接続します。デジタルボルトメー input, connect the meter to the test points at both ターを...

  • Page 12: Service Mode

    4. SERVICE MODE 4. SERVICE MODE MAIN CPU Version, DSP Version, HDMI CPU Version and MAIN CPU Version, DSP Version, HDMI CPU Version and Segment Check Mode Segment Check Mode Connect the mains cord into the unit. 本機に電源コードを接続します。 POWER ON/STANDBY Press the POWER ON/STANDBY button for turn on the ボタンを押し、本機の電源を入れ...
  • Page 13 Should the operation or display seem to be abnormal, reset the unit with the following procedure. To turn on the SR7001/SR8001, press and hold the MULTI and SPEAKERS A/B buttons simultaneously for 3 seconds or more.

  • Page 14: System Error

    5. SYSTEM ERROR 5. SYSTEM ERROR 1. Trouble in EEP-ROM (DSP PWB / IC15) Interface 1. EEP-ROM (DSP PWB / IC15) Interface 異常検出表示 • EEP-ROM (DSP PWB / IC15) との通信で が帰ってこ • If the communication error that ACK did not return by ない状態（通信エラー）が約２秒以上生じた時に表示され...
  • Page 15 29pin(_P_AMP_FAIL) 100 msec and more 43pin (_STANDBY) 29pin (Power Amp Fail) 100msec 2. When "L" of less than 100msec is detected by 29pin ② マイコンの に 未満の "L" 検出がされた場合は Speaker Relay を OFF, MUTE を (Power Amp Fail) of IC17, Speaker Relay becomes 状態にして８秒間その状態を保持する。この間、...

  • Page 16: Update Firmware

    6. UPDATE FIRMWARE 6. UPDATE FIRMWARE [A] SOFTWARE (fdtv306r00.exe) DOWNLOADS [A] SOFTWARE (fdtv306r00.exe) DOWNLOADS AND AND INSTALLS PROCEDURE INSTALLS PROCEDURE [A-1] DOWNLOADS OF THE SOFTWARE [A-1] DOWNLOADS OF THE SOFTWARE (Flash Development Toolkit: the rest is FDT) (Flash Development Toolkit: 以下...
  • Page 17 A login ID is necessary to download the FDT. のダウンロードには Login ID が必要になります。 If you have Login ID, please advance to step 15. 既に Login ID を持っている方は手順の へ進んでくださ If you do not have Login ID, Click the MY RENESAS. い。 Login ID を持っていない方は...
  • Page 18 Click the If you are a new user click here to register If you are a new user click here to register now をク now. リックします。...
  • Page 19 Choose Non Secure or Secure in Security Level at your のネットワーク環境により Choose Security Level か ら Non Secure 、または Secure を選んでください。 network environment. Choose English or another one in Region and Choose Region and Language から日本語をクリックしま Language. す。...
  • Page 20 Input the each item. 各項目を記入します。 NOTE : The items displayed by a language and region are 注意：下記説明は英語ですが、日本語を選んだ場合日本語で表 different. 示されます。...
  • Page 21 If you have inputted the necessary items, check the I 必須項目を入力したならば、同意しますにチェックを入 Agree, and click the Submit. れ、送信をクリックします。...
  • Page 22 The input is needless in this page. このページは入力しなくても結構です。 Scroll down the page. ページをスクロールダウンします。...
  • Page 23 10. Click the Submit. 送信をクリックします。...
  • Page 24 11. Immediately, an E-mail arrives from the RENESAS. 直ちに、 RENESAS から E-mail が届きます。 E-mail 内に有る登録サイトへのリンクをクリックします。 Click the link in the E-mail to go to the registration site, and input the Login ID and Password. Login ID と Password を入力し Submit をクリックします。...
  • Page 25 14. Click the GLOBAL SITE. 14. GLOBAL SITE をクリックします。...
  • Page 26 15. Click the Downloads in the DESIGN SUPPORT. 15. DESIGN SUPPORT 内の Downloads をクリックします。...
  • Page 27 16. Type the "Flash Development toolkit" into the Download 16. Download Title に "Flash Development toolkit" を入力しま Title. す。 And click the Start Search. Start Search をクリックします。...
  • Page 28 17. Click the Flash Development Toolkit of the top on the 検索結果の一番上の Flash Development Toolkit をクリッ table. クします。 NOTE : The latest edition is FDT V3.06 at present. (July, 注意：現時点 (2006 年 月 での最新バージョンは V3.06 になり 2006) It is in FDT V3.06 as follows and explains it. ます。以下...
  • Page 29 18. Input the Login ID and Password. ダウンロードするために Login ID と Password を入力しま す。 And click the Submit. Submit. をクリックします。...
  • Page 30 19. Scroll down the page. ページをスクロールダウンします。...
  • Page 31 20. Check the Agree, and click the Submit. 20. Agree にチェックを入れ、 Submit をクリックします。...
  • Page 32 21. Scroll down the page. ページをスクロールダウンします。...
  • Page 33 22. Click the Download. 22. Download をクリックします。...
  • Page 34 23. Click the Save. 23. Save をクリックします。 24. Save the fdtv306r00.exe on your PC’s hard disc. 24. fdtv306r00.exe を任意のフォルダに保存します。 NOTE : A file name is change by improvement. 注意：ファイル名はバージョンにより変わります。...
  • Page 35 [A-2] INSTALLS OF THE SOFTWARE [A-2] INSTALLS OF THE SOFTWARE (Flash Development Toolkit Ver.3.06) (Flash Development Toolkit Ver.3.06) Open the folder with the downloaded file. ダウンロードしたファイルのあるフォルダを開きます。 And double click the fdtv306r00.exe. fdtv306r00.exe をダブルクリックします。 Click the Next. Next をクリックします。...
  • Page 36 Check the International [English], and click the Next. International [English] にチェックを入れ Next をクリッ クします。 Check the I accept the terms of the license I accept the terms of the license agreement にチェッ agreement, and Click the Next. クを入れ、 Next をクリックします。...
  • Page 37 Click the Next. Next をクリックします。 Check the all file type, and Click the Next. Next 全てのファイルタイプにチェックを入れ、 をクリック します。...
  • Page 38 Click the Next. Next をクリックします。 Click the Install. Install をクリックします。...
  • Page 39 10. The Setup Status bar appears. インストールの状態が表示されます。 11. Click the Finish. 11. Finish をクリックします。...
  • Page 40 12. Click the OK. 12. OK をクリックします。...

  • Page 41: [B] Writing And Update Software

    [B] WRITING AND UPDATE SOFTWARE [B] WRITING AND UPDATE SOFTWARE MAIN マイコン、 のフラッシュ 、および HDMI マイコ Software for MAIN CPU, flash ROM for DSP and HDMI ンのソフトウェアは更新、および書き込みが出来ます。 CPU can be updated/downloaded. Have update/download application software. ("H8Download. 更新および書き込みには書き込み用アプリケーション exe", "da708_writer.exe" and "fdtv306r00.exe (FDT3.06) or が必要です。...

  • Page 42: Mode 1: Update/Download Main Cpu's Software To Internal Flash-Rom

    Mode 1: Update/Download MAIN CPU's software Mode 1: Update/Download MAIN CPU's software to internal Flash-ROM to internal Flash-ROM Update/Download software for MAIN CPU (Mode 1) Update/Download software for MAIN CPU (Mode 1) Put the "MAIN" folder into anywhere on your PC's hard "MAIN"...
  • Page 43 Double click the H8Download.exe. And launch the H8Download.exe をダブルクリックし、 marantz firmware upgrade program を起動します。 marantz firmware upgrade program. Click the Set Ports. Set Ports をクリックします。 Choose the COM Port number. And Click the OK. 使用する ポート番号を選択し、 をクリックしま す。...
  • Page 44 Click the other files... in the Firmware program file. Firmware program file 内の other files... をクリックしま す。 Choose the SR8001_yymmddv.mot. And click the Open. SR8001_yymmddv.mot を選択し、 Open をクリックしま NOTE : The yy is two digits of year. The mm is month. The す。...
  • Page 45 10. Click the Connect. 10. Connect をクリックします。 11. If the connection with the H8 µ-P is successfully made, a 11. H8 マイコンとの接続に成功すると "Success to the H8 dialogue box saying "Success to the H8 micro processor micro processor connection" と表示したダイアログボック connection" appears. If the connection fails, error スが表示されます。接続に失敗するとエラーメッセージが...
  • Page 46 13. If the firmware is updated/downloaded successfully, 書き込みが成功すると "Finished the firmware program sending" と表示したダイアログボックスが表示されます。 a dialog box saying "Finished the firmware program sending" appears. をクリックします。 Click the OK. 14. Click the Close to close the application. 14. Close をクリックしアプリケーションを閉じます。 15. Press the POWER ON/STANDBY button for turn off the 15.

  • Page 47: Mode 2: Update/Download Dsp's Software To 8M Flash-Rom

    Mode 2 : Update/Download DSP’s software to 8M Mode 2: Update/Download DSP s software to 8M Flash-ROM Flash-ROM Update/Download Software for DSP (Mode 2) Update/Download Software for DSP (Mode 2) Put the "DSP" folder into anywhere on your PC's hard "DSP"...
  • Page 48 Double click the da708_writer.exe. And Launch the da708_writer.exe をダブルクリックし、 SR8001 TI SR8001 TI Writer. Writer を起動します。 10. Choose the COM Port number. 使用する ポート番号を選択します。 11. Click the Connect. 11. Connect をクリックします。...
  • Page 49 12. "Connection OK!!" appears on SR8001 TI Writer. And 12. SR8001 TI Writer 上に "Connection OK!!" と表示された ら、 FileOpen をクリックします。 click the FileOpen. 13. Choose the pa17_meqyymmdd_vv.upd. And click the 13. pa17_meqyymmdd_vv.upd を選択し、 Open をクリックし Open. ます。 NOTE : The yy is two digits of year. The mm is month. The 注意：...
  • Page 50 15. Click the SEND. 15. SEND をクリックします。 16. Software is written into the DSP Flash ROM. ソフトウェアが フラッシュ に書き込まれます。 The writing of software takes about 2 minute. 書き込みにかかる時間は約 分です。 17. Click the OK. 17. OK をクリックします。 19. Click the Discon. 18.
  • Page 51 19. Click the Exit. 19. Exit をクリックします。 20. Press the POWER ON/STANDBY button for turn off the 20. POWER ON/STANDBY ボタンを押し、本機の電源を切り unit. ます。 21. Disconnect the mains cord and RS-232C cable from the 本機から電源コードと RS-232C ケーブルを外します。 unit.

  • Page 52: Mode 3: Update/Download Hdmi Cpu's Software To Internal Flash-Rom

    Check the Create a new project workspace, and click Create a new project workspace をチェックし、 を the OK. クリックします。 NOTE : It is needs setup for SR7001/SR8001. When you 注意： SR7001/SR8001 用の設定が必要です。既に設定が終 have already setup, please advance to "[M3-2] わっている方は...
  • Page 53 SR8001_HDMI is inputted into the Workspace Name. Workspace Name に SR8001_HDMI を入力します。 (It is simultaneously inputted into Project Name.) 同時に Project Name にも入力されます Click the OK. をクリックします。 Choose the H8/36087F in Select Device. And click the Select Device から H8/36087F を選択し、...
  • Page 54 Choose the Serial port number in the Select Port. And 6. Select Port から Serial ポート番号を選び、 Next をクリック click the Next. します。 16.0000 is inputted into the Enter the CPU crystal Enter the CPU crystal frequency for the selected device frequency for the selected device.
  • Page 55 Check The BOOT Mode in Select Connection. Select Connection の BOOT Mode をチェックします。 Un-check the Use Default, and choose the 19200 in Recommended Speeds の Use Default のチェックを外 Recommended Speeds. し、 19200 を選択します。 Click the Next. Next をクリックします。 Check the Automatic in Protection. Protection Automatic の...
  • Page 56 [M3-2] Writing Procedure for HDMI CPU [M3-2] Writing Procedure for HDMI CPU Connect the RS-232C on rear panel of the unit and the 本機のリアパネルにある RS-232C コネクタと Windows Serial Port of windows PC with RS-232C cable. の Serial ポートを RS-232C ケーブルで接続します。 Connect the mains cord into the unit.
  • Page 57 Choose SP8001_HDMI.AWS in SR8001_HDMI folder workspase フォルダの下の SR8001_HDMI フォルダ内の under workspase folder. And Click the Open. SP8001_HDMI.AWS を選択し、 Open をクリックしま す。 Right button of mouse click on the SR8001_HDMI, and SR8001_HDMI を右クリックし、メニューから select the Add Files... in a menu. Files... をクリックします。...
  • Page 58 Choose the HDMI_REPV2xyymmddvv.mot, and click HDMI_REPV2xyymmddvv.mot を選択し、 をクリッ the Add. クします。 NOTE : The yy is two digits of year. The mm is month. The 注意： は年の下二桁、 は月、 は日、 はリリースナ dd is date. The vv is release number. ンバー Press the POWER ON/STANDBY button for turn on the POWER ON/STANDBY ボタンを押し、本機の電源を入れ...
  • Page 59 15. Click the Device in the menu bar and select the 15. Device をクリックし、メニューから Connect to Connect to Device. Device をクリックします。 16. Press right button of mouse on the HDMI_ 16. HDMI_REPV2xyymmddvv.mot を右クリックし、メニュ REPV2xyymmddvv.mot, and select the Download File Download File ーから...
  • Page 60 17. Software is written into the HDMI CPU. ソフトウェアが HDMI マイコンに書き込まれます。 The writing of software takes about 45 seconds. 書き込みにかかる時間は約 秒です。 18. Click the Device in the menu bar and select the 18. Device をクリックし、メニューから Disconnect をクリッ Disconnect. クします。...
  • Page 61 19. Click the File and select the Exit in menu. 19. File をクリックし、メニューから Exit をクリックします。 20. Press the POWER ON/STANDBY button for turn off the 20. POWER ON/STANDBY ボタンを押し、本機の電源を切り unit. ます。 21. Disconnect the mains cord and RS-232C cable from the 本機から電源コードと...
  • Page 62 Personal notes:...

  • Page 63: Wiring Diagram

    7. WIRING DIAGRAM...

  • Page 64: Block Diagram

    8. BLOCK DIAGRAM...

  • Page 66: Schematic Diagram

    9. SCHEMATIC DIAGRAM VIDEO PWB...
  • Page 67 COMPONENT PWB...
  • Page 68 HDMI PWB -1/4...
  • Page 69 HDMI PWB -2/4...
  • Page 70 HDMI PWB -3/4...
  • Page 71 HDMI PWB -4/4...
  • Page 72 INPUT PWB...
  • Page 73 DSP PWB 1/2...
  • Page 74 DSP PWB 2/2...
  • Page 76 AMP PWB...
  • Page 77 POWER PWB...
  • Page 78 SELECTOR ENCODER PWB FRONT PWB VOLUME PWB TACT PWB U VERSION ONLY 7.1 CH INPUT PWB H/P PWB PUSH S/W PWB...
  • Page 79 STANDBY PWB RS-232C PWB 7.1 CH PREOUT PWB GUIDE PWB SBLR SPEAKER PWB...
  • Page 80 REGULATOR PWB...

  • Page 81: Parts Location

    10. PARTS LOCATION 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 82 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 83 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 84 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 85 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 86 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 87 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 88 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 89 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 90 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 91 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 92 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 93 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 94 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 95 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 96 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 97 鉛フリー半田 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).

  • Page 98: Exploded View And Parts List

    11. EXPLODED VIEW AND PARTS LIST /K, /U RC91 (/N ONLY) F701 (/U ONLY) (/U ONLY) XM PWB (/U ONLY) HDMI PWB 7.1 CH TUNER MODULE PREOUT /U Only PUSH S/W PWB VIDEO PWB S13 X19 /K, /N Only TACT PWB DSP PWB (/U ONLY) 7.1CH...
  • Page 99 00M391H130030 00M391H130030 DAMPER DUMPER ASSY KDG1A006Z PWB ASSY PUSH S/W PWB ASSY COP11869Z PWB ASSY H/P PWB ASSY CUP11869Z 00M10BW355020 00M10BW355020 LENS INDICATOR THX CGL1A232 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 100 CNVMB014MA08L 61 /N1B PANEL REAR PANEL SR8001 N CKF6A306Z 61 /N1G PANEL REAR PANEL SR8001 N CKF6A306Z 61 /N1S PANEL REAR PANEL SR8001 N CKF6A306Z NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 101 00M05CW257010 LID TOP COVER (BLACK) CKC1A170K117 00M10BW067010 CAP COVER FOR FRONT JACK CGR1A344 90M-ZA000240R ANTENNA AM LOOP ANT CSA1A020Z 90M-ZA000210R ANTENNA ANT FM WIRE (PIGTAIL) CSA1A007 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 102 Personal notes:...

  • Page 103: Microprocessor And Ic Data

    12. MICROPROCESSOR AND IC DATA IC11 : HD64F2505 Port Setting Port Name STBY Name Note Mode7 Act. init 1 PE5 RS232C_SW RS232C Switch (Main CPU or HDMI CPU) 2 PE6 AFDATA Analog Switch Data (TC94A46FG/TC9274N) Analog Switch Clock (TC94A46FG/ 3 PE7 AFCLK TC9274N) 4 PD0...
  • Page 104 IC11 : HD64F2505 Port Setting Port Name STBY Name Note Mode7 Act. init 50 PJ3 _CEDIR DIR Chip Enable (LC89057W) 51 PJ2 _DIR_RST DIR Reset (LC89057W) 52 PJ1 _STBY_LED Standby LED On 53 PJ0 _RSFL Front FL Driver Register Selection (NJU3430) 54 Vss 55 P97/AN15/ I,I,O...
  • Page 105 IC11 : HD64F2505 Port Setting Port Name STBY Name Note Mode7 Act. init 100 ~RES _RES RESET 101 P20/TIOCA3 I/O,O CPU_NMI HDMI CPU WRITE MODE (H8/36087) 102 P21/TIOCB3 I/O,I/O T_IN IR_RECEIVER_IN 103 P22/TIOCC3 I/O,I/O SPIO_ENA Communication Enable from TI DSP (DA708) 104 P23/TIOCD3 I/O,I/O _TI_RST Reset for TI DSP (DA708)
  • Page 106 IC90 : HD64F36087HV Port Setting Port Name STBY Name Note Mode7 Act. init 1 PB6/AN6 to GND (or Temporary Pull up) 2 PB7/AN7 to GND (or Temporary Pull up) 3 Avcc 4 X2 5 X1 6 Vcc 7 _RESET _RES _RST_HDMI also use for JTAG 8 TEST...
  • Page 107 IC90 : HD64F36087HV Port Setting Port Name STBY Name Note Mode7 Act. init 49 P71/RXD_2 I/O DEBUG_RxD RS232C RxD for Debug 50 P72/TXD_2 DEBUG_TxD RS232C TxD for Debug 51 P14/_IRQ0 INT_RX HDMI Rx device Int. 52 P15/_IRQ1 INT_TX1 HDMI Tx device1 Int. /TMIB1 53 P16/_IRQ2 INT_TX2...
  • Page 108 IC19 : CXB1441R IC22 : CXB1441R Termination Input switching resistors Output circuit ADTnP buffer ADTnN YDTnP Equalizer YDTnN BDTnP Quantizer BDTnN n = 1, 2, 3 Termination resistors Input switching Output ACKP circuit buffer ACKN YCKP Equalizer YCKN BCKP Quantizer BCKN Clock Output current...
  • Page 109 IC20 : TC74HC4094AFN IC21 : TC74HC4094AFN IC79 : TC74HC4094AFN IC80 : TC74HC4094AFN IC83 : TC74HC4094AFN IC20 PortSetup Port Name Use STBY Name Note Device Act. MIC_ENABLE 3.3-5.0V L MIC Enable for MRAC (Relay) SPKC_CONT 5.0V L Speaker C Relay Control (Relay) _PUREDIRECT_LED 5.0V H PURE DIRECT LED On...
  • Page 110 IC21 : TC94A46CFG...
  • Page 111 IC22 : TC9274CNG IC27 : CS5361-KS SCLK OVFL LRCK SDOUT MCLK REFGND Serial Output Interface FILT+ Voltage Reference S/LJ AINL- High Digital LP Filter ΔΣ Decimation Pass MDIV AINL+ Filter Filter AINR- High Digital ΔΣ MODE0 LP Filter Decimation Pass AINR+ MODE1 Filter...
  • Page 112 IC27 : CS5361-KS FILT+ REFGND LRCK SCLK AINR+ MCLK AINR- AINL- SDOUT AINL+ MDIV OVFL S/LJ Pin Name Pin Description Reset (Input) - The device enters a low power mode when low. Master/Slave Mode (Input) - Selects operation as either clock master or slave. LRCK Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on the serial audio data line.
  • Page 113 IC29 : LC89057WVF4E EMPHA/UO AUDIO XMODE LC89057W-VF4-E RXOUT Microcontroller C bit , Ubit SDIN RERR SLRCK SBCK Input Demodulation Data Selector & RDATA RDATA Selector Lock detect RX5/VI XMODE RLRCK RX6/UI SDIN DGND DVDD LC89057W-VF4-E DVDD DGND RMCK TMCK/PIO0 RBCK RBCK RLRCK TBCK/PIO1...
  • Page 114 IC32 : TC74VHC157FT (15) Inputs Outputs SELECT SELECT (11) (10) (14) (12) (13) X: Don’t care IC33 : TMS320DA708 1 Second Generation Aureus™ DSP Features • DA708: 32-/64-Bit 250-MHz Floating-Point DSP • Upgrades to C67x+ CPU From DA6xx Family: – 2X CPU Registers [64 General-Purpose] –...
  • Page 115 IC33 : TMS320DA708 Table 2-2. Terminal Functions SIGNAL NAME TYPE PULL GPIO DESCRIPTION External Memory Interface (EMIF) Address and Control EM_A[0] EM_A[1] EM_A[2] EM_A[3] EM_A[4] EM_A[5] EMIF Address Bus EM_A[6] EM_A[7] EM_A[8] EM_A[9] EM_A[10] EM_A[11] EM_BA[0] SDRAM Bank Address and Asynchronous Memory Low-Order Address EM_BA[1] EM_CS[0]...
  • Page 116 IC33 : TMS320DA708 Table 2-2. Terminal Functions (continued) SIGNAL NAME TYPE PULL GPIO DESCRIPTION McASP0, McASP1, McASP2, and SPI1 Serial Ports AHCLKR0/AHCLKR1 McASP0 and McASP1 Receive Master Clock ACLKR0 McASP0 Receive Bit Clock AFSR0 McASP0 Receive Frame Sync (L/R Clock) AHCLKX0/AHCLKX2 McASP0 and McASP2 Transmit Master Clock ACLKX0...
  • Page 117 IC33 : TMS320DA708 Table 2-2. Terminal Functions (continued) SIGNAL NAME TYPE PULL GPIO DESCRIPTION Clocks OSCIN 1.2-V Oscillator Input OSCOUT 1.2-V Oscillator Output OSCV Oscillator 1.2-V V tap point (for filter only) OSCV Oscillator V tap point (for filter only) CLKIN Alternate clock input (3.3-V LVCMOS Input) PLLHV...
  • Page 118 IC33 : TC9482BFG IC34 : TC9482BFG...
  • Page 119 IC33 : TC9482BFG IC33 : TC9482BFG...
  • Page 120 IC34 : M29W800DT70N Figure 2. Logic Diagram Table 1. Signal Names A0-A18 Address Inputs DQ0-DQ7 Data Inputs/Outputs V CC DQ8-DQ14 Data Inputs/Outputs DQ15A–1 Data Input/Output or Address Input A0-A18 DQ0-DQ14 Chip Enable Output Enable DQ15A–1 M29W800DT Write Enable BYTE M29W800DB Reset/Block Temporary Unprotect Ready/Busy Output (not available on SO44 package)
  • Page 121 IC35 : SiI 9033CTU...
  • Page 122 IC36 : TC74VCX157FT IC38 : TC74VCX157FT Pin Assignment IEC Logic Symbol (top view) (15) SELECT SELECT (11) (10) (14) (12) (13) Truth Table Inputs Outputs SELECT X: Don’t care IC38 : TC74VHC157FT...
  • Page 123 IC39 : TC7WH157FU IC41 : SiL 9030CTU-7 Si I 9030 Si I 9030 Features RESET# PanelLink Cinema Transmitter DSCL Master DSDA Registers CSDA Industry-Standard HDCP Configuration Slave CSCL HDCP Keys Logic Encryption Compliance PROM Engine • HDMI 1.0 EXT_SWING VSYNC •...
  • Page 124 IC41 : CS4382A-CQ 114 dB, 192 kHz 8-Channel D/A Converter Features Description 24-bit Conversion The CS4382 is a complete 8-channel digital-to-analog system including digital interpolation, fifth-order delta- Up to 192 kHz Sample Rates sigma digital-to-analog conversion, digital de-emphasis, 114 dB Dynamic Range volume control and analog filtering.
  • Page 125 IC41 : CS4382A-CQ 4 8 4 7 4 6 4 5 4 4 4 3 4 2 4 1 4 0 3 9 3 8 3 7 AOUTA2- DSDA2 DSDB1 AOUTA2+ AOUTB2+ DSDA1 AOUTB2- MCLK CS4382 LRCK1(DSD_EN) AOUTA3- SDIN1 AOUTA3+ SCLK1 AOUTB3+ LRCK2...
  • Page 126 IC41 : CS4382A-CQ Pin Name Pin Description MUTEC1 Mute Control (Output) - The Mute Control pins go high during power-up initialization, reset, muting, MUTEC234 power-down or if the master clock to left/right clock frequency ratio is incorrect. These pins are intended to be used as a control for external mute circuits to prevent the clicks and pops that can occur in any sin- gle supply system.
  • Page 127 IC61 : CS4392KZZ 1. PIN DESCRIPTION - PCM DATA MODE AMUTEC AOUTA- SDATA AOUTA+ SCLK LRCK AGND MCLK AOUTB+ AOUTB- (SCL/CCLK) M2 BMUTEC (SDA/CDIN) M1 CMOUT (AD0/CS) M0 FILT+ Reset (Input) - Powers down device and resets all internal registers to their default settings. Logic Power (Input) - Positive power for the digital input/output.
  • Page 128 IC61 : CS4392KZZ PIN DESCRIPTION - DSD mode AMUTEC AOUTA- DSD_A AOUTA+ DSD_B DSD_MODE AGND MCLK AOUTB+ DSD_SCLK AOUTB- (SCL/CCLK) M2 BMUTEC (SDA/CDIN) M1 CMOUT (AD0/CS) M0 FILT+ DSD_A DSD Data (Input) - Input for Direct Stream Digital serial audio data. DSD_B DSD_Mode DSD Mode (Input) - In stand alone mode, this pin must be set to a logic ‘1’...
  • Page 129 IC62 : ADV7401BS80 OUTPUT FIFO AND FORMATTER...
  • Page 130 IC62 : ADV7401BS80 AIN12 PIN 1 AIN5 AIN11 AIN4 CS/HS AIN10 DGND TEST0 DVDDIO CAPC2 CAPC1 BIAS ADV7401 AGND DGND DVDD REFOUT LQFP AVDD TOP VIEW CAPY2 (Not to Scale) CAPY1 SFL/SYNC_OUT SCLK2 AGND TEST1 DGND DVDDIO AIN3 AIN9 SDA2 AIN2 AIN8 AIN1...
  • Page 131 IC62 : ADV7401BS80 Pin No. Mnemonic Type Function HS/CS HS is a Horizontal Synchronization Output Signal (SDP and CP modes). CS is a Digital Composite Synchronization Signal (and can be selected while in CP mode). Vertical Synchronization Output Signal (SDP and CP modes). FIELD/DE Field Synchronization Output Signal (all interlaced video modes).
  • Page 132 IC63 : CD0040AF MPU Interface Configuration Registers Timing Generator Video Processing Engine Digital Out SDRAM Inter face SDRAM Fig. 2-1: System Block Diagram cvdd 109 72 ivdd MD7 110 71 cvdd MD8 111 70 ovss MD6 112 69 RFFI MD9 113 68 FILM ovdd 114 67 CO9...
  • Page 133 IC63 : CD0040AF Name Attr ibut e Functional Description Name Attr ibut e Functional Description OVDD Positive supply voltage(+3.3V) for Pad Ring OVSS Digital ground for Pad Ring CLKI CMOS System Clock Input (27MHz) CVDD Digital positive supply voltage (+2.5V) for core TEST7 CMOS Test purpose only(must be connected to Ground)
  • Page 134 IC64 : HY57V161610ET-7 1Mx16 Synchronous DRAM Self Refresh Counter Refresh Refresh Interval Timer Counter 512Kx16 Bank 0 Address[0:10] Sense AMP & I/O gates Column Decoder PIN CONFIGURATION Address Precharge Register Row Active BA(A11) DQ15 DQ15 Column Addr. Column Active DQ14 DQ14 Latch &...
  • Page 135 IC71 : NJM2595MTE1 IC72 : NJM2595MTE1 IC73 : NJM2595MTE1 IC81 : NJM2595MTE1 Vin1 Vin2 75Ω Vout1 Driver Vin3 75Ω Vout2 Driver Vin4 Vin5 75Ω Vout3 Driver ■ Control Signal vs. Output Signal (L=V ,H=V , X=L or H) Vout1 Vout2 Vout3 Vin1 MUTE...
  • Page 136 IC75 : NJM2264D IC76 : NJM2244D IC77 : NJM2244D IC82 : NJM2244D...
  • Page 137 IC78 : LC747828A13 Pin No. Symbol Function Description Ground Ground connection (digital system ground) Xtal Used to connect the crystal oscillator and capacitor used to generate the internal Crystal oscillator connection synchronization signal, or to input an external clock (2fsc or 4fsc). Xtal Switches between external clock input mode and crystal oscillator mode.
  • Page 138 IC81 : NJU3430F R S T R ESET Instruction M K R AM Icon D ec oder 16x2 bit D r i v e r 8bits Line Shift C L K Address R e g . Counter C G R AM Segment 35x8 bit D r i v e r...
  • Page 139 IC91 : NJM2584M IC92 : NJM2584M IN1B IN1A IC93 : NJM2584M IC96 : NJM2584M (SR8001 only) BIAS IC97 : NJM2584M (SR8001 only) GND1 IC98 : NJM2584M (SR8001 only) OUT1 IN2B BIAS GND2 OUT2 OUT3 IN2A CLAMP GND3 IN3A IN3B MODE...
  • Page 140 IC92 : ST3232ECWR PIN DESCRIPTION PlN N° SYMBOL NAME AND FUNCTION Positive Terminal for the first Charge Pump Capacitor Doubled Voltage Terminal Negative Terminal for the first Charge Pump Capacitor Positive Terminal for the second Charge Pump Capacitor Negative Terminal for the second Charge Pump Capacitor Inverted Voltage Terminal Second Transmitter Output Voltage Second Receiver Input Voltage...

  • Page 141: Electrical Parts List

    13. ELECTRICAL PARTS LIST NOTE ON SAFETY FOR FUSIBLE RESISTOR : PARTS INFORMATION The suppliers and their type numbers of fusible resistors RESISTORS 1) 00MGD05 × × × 140, Carbon fi lm fi xed resistor, ±5% 1/4W are as follows; 2) 00MGD05 ×...
  • Page 142 00MOA10710020 ELECT CAP. 100UF 100V CCEA2AH101E C512 00MOA10710020 ELECT CAP. 100UF 100V CCEA2AH101E C513 00MOA10710020 ELECT CAP. 100UF 100V CCEA2AH101E C514 00MOA10710020 ELECT CAP. 100UF 100V CCEA2AH101E NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 143 CVDZJ3.6BT D411 90M-HD302380R 90M-HD302380R ZENER DIODE ZJ3.6BT CVDZJ3.6BT D412 90M-HD302380R 90M-HD302380R ZENER DIODE ZJ3.6BT CVDZJ3.6BT D413 00MHD20015210 DIODE 1SS133T-77 CVD1SS133MT D414 00MHD20015210 DIODE 1SS133T-77 CVD1SS133MT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 144 J111 CORD SN95/PB5, 0.6 C3A206 J112 CORD SN95/PB5, 0.6 C3A206 J113 CORD SN95/PB5, 0.6 C3A206 J114 CORD SN95/PB5, 0.6 C3A206 J115 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 145 J317 CORD SN95/PB5, 0.6 C3A206 J318 CORD SN95/PB5, 0.6 C3A206 J319 CORD SN95/PB5, 0.6 C3A206 J320 CORD SN95/PB5, 0.6 C3A206 J321 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 146 J525 CORD SN95/PB5, 0.6 C3A206 J526 CORD SN95/PB5, 0.6 C3A206 J527 CORD SN95/PB5, 0.6 C3A206 J528 CORD SN95/PB5, 0.6 C3A206 J529 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 147 J806 CORD SN95/PB5, 0.6 C3A206 J807 CORD SN95/PB5, 0.6 C3A206 J808 CORD SN95/PB5, 0.6 C3A206 J809 CORD SN95/PB5, 0.6 C3A206 J810 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 148 Q622 00MHC20001080 00MHC20001080 IC ! SAP17PLFNO.552 HVISAP17P Q623 00MHT800931A0 00MHT800931A0 TRS. KTC3200GR HVTKTC3200GRT Q624 00MHT800931A0 00MHT800931A0 TRS. KTC3200GR HVTKTC3200GRT Q703 00MHT600121A0 00MHT600121A0 TRS. KTA1268GR HVTKTA1268GRT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 149 15 OHM 1/6W J CRD20TJ150T R451 RES. 10 OHM 1/5W J CRD20TJ100T R452 RES. 10 OHM 1/5W J CRD20TJ100T R453 RES. 1K OHM 1/5W J CRD20TJ102T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 150 47 OHM 1W J KRG1SANJ470RT R546 RES. 47 OHM 1W J KRG1SANJ470RT R549 RES. 15 OHM 1/6W J CRD20TJ150T R550 RES. 15 OHM 1/6W J CRD20TJ150T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 151 120 OHM 1W J KRG1SANJ121RT R643 RES. 120 OHM 1W J KRG1SANJ121RT R644 RES. 120 OHM 1W J KRG1SANJ121RT R645 RES. 47 OHM 1W J KRG1SANJ470RT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 152 68K OHM 1/5W J CRD20TJ683T R803 RES. 68K OHM 1/5W J CRD20TJ683T R804 RES. 68K OHM 1/5W J CRD20TJ683T R805 RES. 68K OHM 1/5W J CRD20TJ683T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 153 CCEA1HH100T COMP C863 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T COMP C901 00MOA47602520 ELECT CAP. 47UF 25V CCEA1EH470T COMP C902 00MOA47602520 ELECT CAP. 47UF 25V CCEA1EH470T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 154 C970 00MOA47602520 ELECT CAP. 47UF 25V CCEA1EH470T COMP C971 00MDK96103300 CER. CAP. 0.01UF 50V KC CCUS1H103KC COMP C972 00MDK96103300 CER. CAP. 0.01UF 50V KC CCUS1H103KC NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 155 1K OHM 1/10W J CRJ10DJ102T COMP R863 00MNN05223610 CHIP RES. 22K OHM 1/10W J CRJ10DJ223T COMP R864 00MNN05223610 CHIP RES. 22K OHM 1/10W J CRJ10DJ223T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 156 470 OHM 1/10W J CRJ10DJ471T COMP R959 00MNN05471610 CHIP RES. 470 OHM 1/10W J CRJ10DJ471T COMP R960 00MNN05471610 CHIP RES. 470 OHM 1/10W J CRJ10DJ471T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 157 0.1UF 25V ZF CCUS1E104ZF C132 00MDK96104300 CER. CAP. 0.1UF 25V ZF CCUS1E104ZF C133 00MDK96104300 CER. CAP. 0.1UF 25V ZF CCUS1E104ZF C134 00MDK96182300 CER. CAP. 1800PF/50V/1608/X7R CCUS1H182KC NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 158 CCUS1H471JA C201 00MDD91100300 CER. CAP. 10PF 50V JA CCUS1H100JA C202 00MDD91100300 CER. CAP. 10PF 50V JA CCUS1H100JA C203 00MDD95471300 CER. CAP. 470PF 50V JA CCUS1H471JA NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 159 22UF 50V CCEA1HH220T C335 00MDK96104300 CER. CAP. 0.1UF 25V ZF CCUS1E104ZF C336 00MOA22605020 ELECT CAP. 22UF 50V CCEA1HH220T C337 00MDK96104300 CER. CAP. 0.1UF 25V ZF CCUS1E104ZF NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 160 17P WAFER CARD CABLE CJP17GA115ZY CN34 /N1G CONN. 17P WAFER CARD CABLE CJP17GA115ZY CN34 /N1S CONN. 17P WAFER CARD CABLE CJP17GA115ZY CN34 /U1B CONN. 15P CARD CABLE CJP15GA115ZY NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 161 00MHC700400Z0 00MHC700400Z0 IC TC74HCU04AFN HVITC74HCU04AFN IC23 00MHC011905K0 00MHC011905K0 IC TC74VHC153FT CVITC74VHC153FT IC24 90M-HC700630R 90M-HC700630R IC TC74VHCT04AFN CVITC74VHCT04AFN IC25 00MHC10172090 00MHC10172090 IC NJM2115MD OP AMP HVINJM2115MDTE1 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 162 90M-HX600010R CHIP TRS. KRA102S HVTKRA102S QC24 90M-HX800010R 90M-HX800010R CHIP TRS. KRC102S HVTKRC102S QC25 90M-HX800010R 90M-HX800010R CHIP TRS. KRC102S HVTKRC102S QC26 90M-HX600010R 90M-HX600010R CHIP TRS. KRA102S HVTKRA102S NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 163 00MNN05104610 CHIP RES. 100K OHM 1/10W J CRJ10DJ104T R166 00MNN05104610 CHIP RES. 100K OHM 1/10W J CRJ10DJ104T R167 00MNN05391610 CHIP RES. 390 OHM 1/10W J CRJ10DJ391T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 164 00MNN05562610 CHIP RES. 5.6K OHM 1/10W J CRJ10DJ562T R237 00MNN05270610 CHIP RES. 27 OHM 1/10W J CRJ10DJ270T R238 00MNN05100610 CHIP RES. 10 OHM 1/10W J CRJ10DJ100T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 165 00MNN05473610 CHIP RES. 47K OHM 1/10W J CRJ10DJ473T RC16 00MNN05221610 CHIP RES. 220 OHM 1/10W J CRJ10DJ221T RC17 00MNN05470610 CHIP RES. 47 OHM 1/10W J CRJ10DJ470T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 166 00MNN05222610 CHIP RES. 2.2K OHM 1/10W J CRJ10DJ222T RC81 00MNN05683610 CHIP RES. 68K OHM 1/10W J CRJ10DJ683T RC82 00MNN05223610 CHIP RES. 22K OHM 1/10W J CRJ10DJ223T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 167 HCBS1H101KBT FRONT C809 CER. CAP. 100PF 50V K HCBS1H101KBT FRONT C810 CER. CAP. 100PF 50V K HCBS1H101KBT FRONT C811 CER. CAP. 100PF 50V K HCBS1H101KBT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 168 C3A206 FRONT J837 CORD SN95/PB5, 0.6 C3A206 FRONT J838 CORD SN95/PB5, 0.6 C3A206 FRONT J839 CORD SN95/PB5, 0.6 C3A206 FRONT J840 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 169 CRD20TJ103T FRONT R913 RES. 10K OHM 1/5W J CRD20TJ103T FRONT R914 RES. 10K OHM 1/5W J CRD20TJ103T FRONT R915 RES. 10K OHM 1/5W J CRD20TJ103T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 170 CST1A012ZT FRONT SW83 90M-SP001210R 90M-SP001210R SW SKHV10910G TACT CST1A012ZT FRONT SW84 90M-SP001210R 90M-SP001210R SW SKHV10910G TACT CST1A012ZT FRONT SW85 90M-SP001210R 90M-SP001210R SW SKHV10910G TACT CST1A012ZT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 171 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF HDMI C303 00MDK96104300 CER. CAP. 0.1UF 50V K CCUS1H104KC HDMI C304 00MDK96104300 CER. CAP. 0.1UF 50V K CCUS1H104KC NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 172 C371 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF HDMI C372 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF HDMI C373 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 173 90M-EQ000040R ELECT CAP. 10UF 25V NON-POLAR CCEA1EN100T HDMI C640 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF HDMI C641 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 174 C808 00MOA47602520 ELECT CAP. 47UF 25V CCEA1EH470T HDMI C809 00MDD95220300 CER. CAP. 22PF 50V JA HCUS1H220JA HDMI C810 00MDD91090300 CER. CAP. 9PF 50V JA CCUS1H9R0JA NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 175 C941 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF HDMI C942 00MDK96104300 CER. CAP. 0.1UF 25V ZF HCUS1E104ZF HDMI C943 00MOA10701620 ELECT CAP. 100UF 16V CCEA1CH101T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 176 90M-HC300940R IC LM1117-ADJ HVILM1117S-ADJ HDMI IC97 90M-HC300940R 90M-HC300940R IC LM1117-ADJ HVILM1117S-ADJ HDMI IC98 90M-HC300940R 90M-HC300940R IC LM1117-ADJ HVILM1117S-ADJ HDMI IC99 90M-HC300940R 90M-HC300940R IC LM1117-ADJ HVILM1117S-ADJ NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 177 90M-HT800110R TRS. KTC4075GR HVTKTC4075GR HDMI Q808 90M-HT600050R 90M-HT600050R TRS. KTA2014GR HVTKTA2014GR HDMI Q809 90M-HT800110R 90M-HT800110R TRS. KTC4075GR HVTKTC4075GR HDMI Q810 90M-HT600050R 90M-HT600050R TRS. KTA2014GR HVTKTA2014GR NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 178 100 OHM 1/10W J CRJ10DJ101T HDMI R302 00MNN05101610 CHIP RES. 100 OHM 1/10W J CRJ10DJ101T HDMI R303 00MNN05101610 CHIP RES. 100 OHM 1/10W J CRJ10DJ101T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 179 0 OHM 1/10W J CRJ10DJ0R0T HDMI R378 00MNN05220610 CHIP RES. 22 OHM 1/10W J CRJ10DJ220T HDMI R379 00MNN05101610 CHIP RES. 100 OHM 1/10W J CRJ10DJ101T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 180 390 OHM 1/10W J CRJ10DJ391T HDMI R671 00MNN05272610 CHIP RES. 2.7K OHM 1/10W J CRJ10DJ272T HDMI R672 90M-NN000860R CHIP RES. 300 OHM 1/10W J CRJ10DJ301T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 181 18K OHM 1/10W J CRJ10DJ183T HDMI R850 00MNN05103610 CHIP RES. 10K OHM 1/10W J CRJ10DJ103T HDMI R851 00MNN05471610 CHIP RES. 470 OHM 1/10W J CRJ10DJ471T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 182 22 OHM X4 2012 CRJ104DJ220T HDMI RN37 90M-BW000400R 90M-BW000400R RES. COMPO. 22 OHM X4 2012 CRJ104DJ220T HDMI RN38 90M-BW000400R 90M-BW000400R RES. COMPO. 22 OHM X4 2012 CRJ104DJ220T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 183 00MDD95471300 CER. CAP. 470PF 50V JA CCUS1H471JA INPUT C218 00MDD95471300 CER. CAP. 470PF 50V JA CCUS1H471JA INPUT C219 00MDD95471300 CER. CAP. 470PF 50V JA CCUS1H471JA NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 184 00MDK96104300 CER. CAP. 0.1UF 50V ZF CCUS1H104ZF INPUT C291 00MDK96104300 CER. CAP. 0.1UF 50V ZF CCUS1H104ZF INPUT C292 00MDD95101300 CER. CAP. 100PF 50V JA CCUS1H101JA NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 185 INPUT C358 90M-OA000130R ELECT CAP. 22UF 50V HCEA1HAHS220T INPUT C359 90M-OA000100R ELECT CAP. 47UF 50V HCEA1EAHS470T INPUT C360 00MDD95101300 CER. CAP. 100PF 50V JA CCUS1H101JA NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 186 C425 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T INPUT C426 00MDK96104300 CER. CAP. 0.1UF 50V ZF CCUS1H104ZF INPUT C427 00MDK96104300 CER. CAP. 0.1UF 50V ZF CCUS1H104ZF NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 187 90M-HT300970R TRS. KTC2875B HVTKTC2875B INPUT Q224 90M-HT300970R 90M-HT300970R TRS. KTC2875B HVTKTC2875B INPUT Q225 90M-HT300970R 90M-HT300970R TRS. KTC2875B HVTKTC2875B INPUT Q226 90M-HT300970R 90M-HT300970R TRS. KTC2875B HVTKTC2875B NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 188 47K OHM 1/10W J CRJ10DJ473T INPUT R255 00MNN05473610 CHIP RES. 47K OHM 1/10W J CRJ10DJ473T INPUT R256 00MNN05473610 CHIP RES. 47K OHM 1/10W J CRJ10DJ473T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 189 10K OHM 1/10W J CRJ10DJ103T INPUT R323 00MNN05330610 CHIP RES. 33 OHM 1/10W J CRJ10DJ330T INPUT R324 00MNN05330610 CHIP RES. 33 OHM 1/10W J CRJ10DJ330T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 190 1K OHM 1/10W J CRJ10DJ102T INPUT R390 00MNN05822610 CHIP RES. 8.2K OHM 1/10W J CRJ10DJ822T INPUT R391 00MNN05822610 CHIP RES. 8.2K OHM 1/10W J CRJ10DJ822T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 191 90M-SP001250R SW ! JPP1197CSA64 KSH1A001ZV POWER PWB (CUP11873Z) POWER BK10 BRACKET BRACKET PWB CMD1A387 POWER BN65 CORD WIRE ASSY CWB3F006150UZ POWER BN81 CORD WIRE ASSY CWB1B906200EN NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 192 C3A206 POWER J604 CORD SN95/PB5, 0.6 C3A206 POWER J605 CORD SN95/PB5, 0.6 C3A206 POWER J606 CORD SN95/PB5, 0.6 C3A206 POWER J607 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 193 C3A206 POWER J690 CORD SN95/PB5, 0.6 C3A206 POWER J691 CORD SN95/PB5, 0.6 C3A206 POWER J692 CORD SN95/PB5, 0.6 C3A206 POWER J693 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 194 CRD20TJ103T POWER R639 RES. 1 OHM 1/4W J CRD25TJ1R0T POWER R640 RES. 2.2K OHM 1W J KRG1SANJ222RT POWER R641 RES. 2.2K OHM 1W J KRG1SANJ222RT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 195 J915 CORD SN95/PB5, 0.6 C3A206 J916 CORD SN95/PB5, 0.6 C3A206 J917 CORD SN95/PB5, 0.6 C3A206 J918 CORD SN95/PB5, 0.6 C3A206 J920 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 196 KRG1SANJ471RT SBLR R819 RES. 470 OHM 1W J KRG1SANJ471RT SBLR RY81 00MLY20240490 00MLY20240490 RELAY 5GPA-28 DC24 HSL3B013ZE SBLR RY82 00MLY20240490 00MLY20240490 RELAY 5GPA-28 DC24 HSL3B013ZE NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 197 90M-FS001090R 90M-FS001090R FUSE ! 5A/250V(EUR) T5AL KBA2C5000TLEY ST-BY F701 /N1S 90M-FS001090R 90M-FS001090R FUSE ! 5A/250V(EUR) T5AL KBA2C5000TLEY ST-BY F701 /U1B 90M-FS001080R FUSE ! 10A/250V KBA2C1002TLEY NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 198 CCEA1HH100T VIDEO C733 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T VIDEO C734 CER. CAP. 47PF 50V JC CCCT1H470JC VIDEO C735 00MOA47701020 ELECT CAP. 470UF 10V CCEA1AH471T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 199 0.01UF 50V Z CCFT1H103ZF VIDEO C800 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T VIDEO C801 CORD SN95/PB5, 0.6 C3A206 VIDEO C802 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 200 C3A206 VIDEO J705 CORD SN95/PB5, 0.6 C3A206 VIDEO J706 CORD SN95/PB5, 0.6 C3A206 VIDEO J707 CORD SN95/PB5, 0.6 C3A206 VIDEO J708 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 201 C3A206 VIDEO J773 CORD SN95/PB5, 0.6 C3A206 VIDEO J774 CORD SN95/PB5, 0.6 C3A206 VIDEO J775 CORD SN95/PB5, 0.6 C3A206 VIDEO J776 CORD SN95/PB5, 0.6 C3A206 NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 202 VIDEO JK76 90M-YT003770R 90M-YT003770R TERMINAL S-VIDEO (2P/H) CJJ9N005Z VIDEO L701 COIL 33UH HLQ02C330JT VIDEO L702 COIL 10UH,K HLQ02C100KT VIDEO Q701 00MHT600111B0 00MHT600111B0 TRS. KTA1267Y HVTKTA1267YT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 203 C3A206 VIDEO R750 RES. 10K OHM 1/5W J CRD20TJ103T VIDEO R752 RES. 75 OHM 1/5W J CRD20TJ750T VIDEO R753 RES. 220 OHM 1/5W J CRD20TJ221T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 204 0.01UF 50V Z HCBS1H103ZFT C847 00MOA47602520 ELECT CAP. 47UF 25V CCEA1EH470T C848 CER. CAP. 0.1UF 50V Z HCBS1H104ZFT C852 CER. CAP. 0.1UF 50V Z HCBS1H104ZFT NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 205 CCEA1EH470T C611 /U1B 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T C612 /U1B 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T C613 /U1B 00MOA10605020 ELECT CAP. 10UF 50V CCEA1HH100T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 206 22 OHM 1/10W J CRJ10DJ220T R521 /U1B 00MNN05223610 CHIP RES. 22K OHM 1/10W J CRJ10DJ223T R522 /U1B 00MNN05223610 CHIP RES. 22K OHM 1/10W J CRJ10DJ223T NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.
  • Page 207 R812 /U1B 00MNM11800020 CHIP RES. 180 OHM 1% CRJ10DF1800T R813 /U1B 00MNM11800020 CHIP RES. 180 OHM 1% CRJ10DF1800T X501 /U1B 00D2623516908 X'TAL 45.1584 MHZ COX45158ISCR NOTE : "nsp" PART IS LISTED FOR REFERENCE ONLY, MARANTZ WILL NOT SUPPLY THESE PARTS.

  • Page 208: About Replace The Microprocessor With A New One

    Pos. After Description Remark Name replaced IC17 HD64F2506 SR8001 IC34 M29W800DT70N SR8001 DHMI IC90 HD64F36087HV SR8001 After replaced A : Mask ROM (With software). No need write-in of software to the microprocessor. B : Flash ROM (With software). Usually, no need write-in of software. But, when the software was updated, you should be write-in of the new software to the microprocessor or flash ROM.

This manual is also suitable for:

Sr8001 n1bSr8001 n1gSr8001 n1sSr8001 u1b

Table of Contents