Advanced Connecting; Connecting The Remote Control Jacks - Marantz SR4002/SR5002 User Manual

ADVANCED CONNECTING

R L R L
R L R L R L
CENTER
FM ( ( 75 75) )
L FM GND GND AM AM
ANTENNA ANTENNA
L L L L SL SL SL SL C C C C
R
L L L L
FRONT SURR. SURR. SUB
BACK WOOFER
R R R R
R R R R SR SR SR SR SW SW SW SW
( ( AUX2 ( ( AUX2 AUX2) ) AUX2) ) 7.1CH INPUT 7.1CH INPUT 7.1CH INPUT 7.1CH INPUT
RS-232C RS-232C SPEAKER C SPEAKER C
OFF ON OFF
L L L L SL SL SL SL C C C C
DVD Audio player
or
R R R R SR SR SR SR SW SW SW SW
Super Audio CD Multi
PRE OUT PRE OUT PRE OUT PRE OUT
channel player
L R L R
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 31.
22
R L
R L R L
VIDEO VIDEO
S-VIDEO S-VIDEO
L
TV TV DVD DVD VCR IN VCR IN
SBL SBL SBL SBL
R
FRONT SURR. SURR.
SBR SBR SBR SBR MULTI. MULTI. IN IN
OUT OUT TV TV DVD DVD VCR VC
Power
ON
Amplifer
SBL SBL SBL SBL
R R L L
Subwoofer
FRONT FRONT B B
FRONT A OR B.CENTER. FRONT A OR B.CENTER.
SBR SBR SBR SBR
FRONT A + + B : 8 OHMS
FRONT A B : 8 OHMS
L R
Front
Left
Surround
Left
Surround
Back Left
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.

CONNECTING THE REMOTE CONTROL JACKS

INPUT INPUT
1 1
INPUT INPUT
2 2
DVD DVD VCR IN VCR IN VCR OUT VCR OUT DSS DSS MONITOR OUT MONITOR OUT Y Y
IN IN OUT OUT IN IN OUT OUT
DVD DVD VCR VCR DSS DSS TAPE TAPE
AUDIO AUDIO
R L
L L R R L L R R L L
CENTER
FRONT B B T FRONT FRONT A A SURROUND BACK SURROUND BACK
FRONT A OR B.CENTER. CENTER. SPEAKER C/MULTI SPEAKER SPEAKER C/MULTI SPEAKER
FRONT A + B : 8 OHMS : 8 OHMS SURR.SURR BACK : 6-8 OHMS SURR.SURR BACK : 6-8 OHMS
SUB
BACK WOOFER
CD recorder
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
Front
Center
Right
Surround
q
Right
You can control other Marantz products through this
unit with the remote controller by connecting the
Surround
REMOTE CONTROL terminals on each unit.
Back Right
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er's, power
switch is synchronized with this unit's power switch.
Set the REMOTE CONTROL SWITCH on the
back of other units (not the SR4002/SR5002) to
"EXT".(EXTERNAL) to use this feature.
COMPONENT COMPONENT
INPUT INPUT
VIDEO VIDEO
3 3
MONITOR MONITOR
1 1
OUT 2 OUT 2
2
INPUT 1 INPUT 1
C C B B / / P P B B C C R R / / P P R R Y Y C C B B P P / / B B C C R R / / P P R R Y Y C C B B P P / / B B C C R R / / P P R R
IN IN IN IN
4 4 5 5
1 1 2 2 3 3
IN IN OUT OUT OPT OPT OUT OUT OUT OUT FLASHER FLASHER DC DC
CD/CDR CD/CDR DIGITAL IN DIGITAL IN DIGITAL OUT DIGITAL OUT REMOTE CONT. REMOTE CONT. REMOTE CONT. REMOTE CONT. IN IN TRIGGER TRIGGER
AC IN AC IN
R R L L
SURROUND SURROUND CENTER CENTER
SWITCHED SWITCHED 1
SPEAKER SPEAKER 1.25A 150W 1.25A 150W
MODEL NO. SR5002 MODE
SYSTEMS SYSTEMS
AC OUTLETS AC OUTLETS
120V 120V 60Hz 60Hz
DVD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the unit, be sure
to always disable operation of the infrared sensor on
the unit by using the following procedure.
1.
Hold down the 7.1CH INPUT (SR4002) / MULTI
(SR5002) button and MENU button on the front
panel at the same time for fi ve seconds.
2.
The setting "IR=ENABLE" is shown on the FL
DISPLAY.
3. Press the 1 or 2 cursor button to change this to
"IR=DISABLE".
4.
Press the ENTER button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
Be sure to set to "IR=ENABLE" when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to "IR=ENABLE".
RC OUT
OPTION
CD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL