Advanced Connecting; Connecting The Remote Control Jacks - Marantz SR4001 User Manual

ADVANCED CONNECTING

R L R L
R L R L R L
CENTER
FM (75Ω)
L GND AM
ANTENNA
L L SL SL C C
R
L L
FRONT SURR. SURR. SUB
BACK WOOFER
R R
R R SR SR SW SW
(AUX2) (AUX2) 7.1CH INPUT 7.1CH INPUT
RS-232C SPEAKER C
OFF ON
L L SL SL C C
DVD Audio player
or
R R SR SR SW SW
Super Audio CD Multi
PRE OUT PRE OUT
channel player
L R L R
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 29.
20
R L
R L R L
VIDEO
S-VIDEO
L
TV DVD VCR IN
SBL SBL
R
FRONT SURR. SURR.
SBR SBR MULTI. IN
OUT TV DVD VC
Power
Amplifer
SBL SBL
R L
Subwoofer
FRONT B
SBR SBR
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIM
FRONT A AND B:MINIMU
L R
Front
Left
Surround
Left
Surround
Back Left
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifi ers.
Be sure to connect each speaker to the corresponding
external power amplifi er.

CONNECTING THE REMOTE CONTROL JACKS

INPUT
1
INPUT
2
DVD VCR IN VCR OUT DSS/VCR2 MONITOR OUT Y
IN OUT IN IN OUT
DVD VCR1 DSS/VCR2 CD TAPE
AUDIO
R L
L R L R L
CENTER
T B FRONT A SURROUND BACK
SPEAKER C/
B.CENTER.
MULTI SPEAKER
BACK : 6-8 OHMS
: 8 OHMS
SUB
BACK WOOFER
CD recorder
UNSWITCHED REMOTE
1.25A 150W
CONTROL
IN
OUT
SWITCHED
1.25A 150W
EXTERNAL INTERNAL
AC OUTLETS
120V 60Hz
Front
Center
Right
Surround
q
Right
You can control other Marantz products through
this unit with the remote control by connecting the
Surround
REMOTE CONTROL terminals on each unit.
Back Right
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er's, power
switch is synchronized with this unit's power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for this
feature.
COMPONENT
INPUT
VIDEO
3
MONITOR
OUT 2
2
INPUT 1
C B / P B C R / P R Y C B / P B C R P / R Y C B / P B C R P / R
3 4 COAX IN IN
IN OUT 1 2 3 OPT OUT OUT FLASHER DC
CDR/MD DIGITAL IN DIGITAL OUT RC-5 RC-5 IN TRIGER
R L
SURROUND CENTER 1
AC OUTLET
SPEAKER 230V 50/60Hz
SYSTEMS SWITCHED
0.65A 150W
MD deck
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR4001/
SR5001, be sure to always disable operation of
the infrared sensor on the main unit by using the
following procedure.
1.
Hold down the 7.1CH INPUT (SR4001) / MULTI
(SR5001) button and MENU button on the front
panel at the same time for fi ve seconds.
2.
The setting "IR=ENABLE" is shown on the FL
DISPLAY.
3. Press the 1 or 2 cursor button to change this to
"IR=DISABLE".
4.
Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
Be sure to set to "IR=ENABLE" when external
infrared sensors or similar devices are not connected.
Otherwise, the main unit will be unable to receive
remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to "IR=ENABLE".
RC OUT
OPTION
CD player
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL