NAPCO Gemini GEM-P3200 Programming Instructions Manual page 60

Page 60
STEP 4: EVENT ID CODES:
Select 2-digit Event ID from Table 4 (below); enter in corresponding address locations (left and right digit).
EVENT ID CODES
DATA ENTRIES
LEFT RIGHT
blank (•) blank (•)
blank (•) 1
C blank (•)
C 1
blank (•) 8
blank (•) 9
blank (•) 0
blank (•) B
blank (•) C
blank (•) D
blank (•) E
blank (•) F
1 blank (•)
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
1 0
1 B
1 C
1 D
1 E
1 F
2 blank (•)
2 1
2 2
2 3
2 4
2 5
2 6
2 7
2 8
2 9
2 0
2 B
2 C
2 D
2 E
2 F
3 blank (•)
3 1
3 2
3 3
3 4
3 5
3 6
3 7
X
GEM-P3200 Programming Instructions
Each relay event can be assigned any of the available event IDs from the table.
TABLE 4
OPTION
Area 1 Arm
Area 2 Arm
Area 1 Disarm
Area 2 Disarm
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Zone 9
Zone 10
Zone 11
Zone 12
Zone 13
Zone 14
Zone 15
Zone 16
Zone 17
Zone 18
Zone 19
Zone 20
Zone 21
Zone 22
Zone 23
Zone 24
Zone 25
Zone 26
Zone 27
Zone 28
Zone 29
Zone 30
Zone 31
Zone 32
Zone 33
Zone 34
Zone 35
Zone 36
Zone 37
Zone 38
Zone 39
Zone 40
Zone 41
Zone 42
Zone 43
Zone 44
Zone 45
Zone 46
Zone 47
Zone 48
6 8 Area 1 Keypad Ambush
6 9 Area 1 Keypad Panic
6 0 Area 1 Keypad Fire
6 B Area 1 Keypad Medical
6 C Keypad Tamper
6 D Area 1 Fail to Open
6 E Area 1 Fail to Close
7 blank (•) Area 2 Keypad Ambush
7 1 Area 2 Keypad Panic
7 2 Area 2 Keypad Fire
7 3 Area 2 Keypad Medical
7 5 Area 2 Fail to Open
7 6 Area 2 Fail to Close
0 8 Test Timer
0 0 Bus Fail
0 B Guarded RAM Fail
0 C Low Battery
0 D AC Fail
0 E EZM Tamper
0 F Sensor Watch
B blank (•) Telco Fault
B 8 Digital Dialer Test
B 9 RESERVED
B B Service Message
B C Program Change
B D RF Receiver Trouble
B E Transmitter Tamper
B F Transmitter Trouble
D blank (•) Keypad Fail
D 1 EZM Fail
D 2 Quickloader Device Control
D 3 System Shutdown
D 4 Quickloader Keypad Reset
D 5 General System Alarm
D 8 Area 1 General System Alarm
D 9 Area 2 General System Alarm
F blank (•) Relay Group 1
F 1 Relay Group 2
F 8 Area 1 Entry Delay
F 9 Area 2 Entry Delay
NOTE: Keypad Tamper must be enabled in
UL installations using jumper option
on keypad.
L
WI1184B 2/06
Continued
NAPCO Security Systems