NAPCO Gemini GEM-P3200 Programming Instructions Manual page 22

Page 22
28
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
NOTE: When programming the ID Code number, "0" through "9" = 0 through 9; A = G0; B = G1; C =
G2; D = G3; E = G4 and "F" = G5.
Z N # X M I T # + C S P
Z n 0 1 - 0 0 0 0 0 0 : 0 - 0
Z N # X M I T # + C S P
Z N 0 1 - E N R O L L : A - -
Example. A 2-point transmitter has the RF ID number 287613:1. Map
point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that one
KEYFOB ZONE ASSIGNMENT: Keyfobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the
keyfob, the location where the person holding the keyfob is stationed, or the special purpose of the keyfob button being de-
pressed. See the next page on Keyfob Transmitters as Zone Input Devices .
29
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
NOTE: When programming the ID Code number, "0" through "9" = 0 through 9; A = G0; B = G1;
C = G2; D = G3; E = G4 and "F" = G5.
X
GEM-P3200 Programming Instructions
RF Transmitter Points (Press
For each transmitter enter: (For wireless systems only. Also see Quick Method, which follows)
•
The zone number (01–48) to which the transmitter will be mapped.
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•
The point number (1–2); enter "9" for unsupervised (all points).
U
•
Press to save and NEXT/YES button to proceed when all transmitters have been entered.
Quick Method (Enroll Method).
points can be programmed automatically ("enrolled") using the following procedure. NOTE: The trans-
mitter point will be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press B to enter the Enroll Mode. The red and green LEDs on the keypad will flash and the window
will display as shown at left.
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep to indicate that the point has been successfully en-
rolled. Multi-point transmitters can be mapped to successive zones simultaneously.
Keyfob Transmitters as Arm/Disarm & Control Devices (Press
Keyfobs can be programmed as "Arm/Disarm" devices using their On/Off buttons (refer to WI752).
For each Keyfob Transmitter, enter:
•
The Keyfob Transmitter number (01–08).
•
The area number to which transmitter is assigned (0 to disable keyfob, 1 or 2).
•
The 6-digit RF ID # and 1-digit checksum number printed on the transmitter and box,
•
The Aux 1 Option (see keyfob aux 1 & aux 2 options).
•
The Aux 2 Option (see keyfob aux 1 & aux 2 options).
U
•
Press to save and NEXT/YES button to proceed when all keyfobs have been entered.
to set cursor.)
R
If a receiver is already installed in the panel, transmitter wireless
point has been programmed. (Transmitter 287613:1, point 1 will be
mapped to Zone 6).
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad will
beep once to indicate that one point has been programmed.
(Transmitter 287613:1, point 2 is mapped to Zone 9).
L
WI1184B 2/06
to set cursor).
R
NAPCO Security Systems