Using A New Accessory; Pairing A New Speed Sensor With Training Computer; Pairing A New Cadence Sensor With Training Computer; Pairing A New Gps Sensor With Training Computer - Polar Electro RCX5 User Manual

Training computer
Hide thumbs Also See for RCX5:
Table of Contents

Advertisement

11. USING A NEW ACCESSORY

Before taking a new accessory into use, it has to be introduced to the training computer. This is called
pairing and takes only a few seconds. Pairing ensures that your training computer receives signals from
your accessory only, and enables disturbance-free training in a group.

Pairing a New Speed Sensor With Training Computer

Make sure the speed sensor has been correctly installed. For more information, on installing the speed
sensor refer to the user manual of the speed sensor or for video tutorial at
http://www.polar.fi/en/support/video_tutorials.
1.
Go to
>
Menu
Settings
and press OK.
new
2.
Press OK to start the test drive
3.
Press OK and
Searching for new speed sensor
the speed sensor signal. Rotate the wheel a few times to activate the sensor. The flashing red light in the
sensor indicates that the sensor is activated.
4.
Once the new speed sensor is identified,
5.
If the search is not successful,
,
further.
Try again? YES / NO
6.
Select
to start the search again.
YES
7.
Select
to cancel the searching.
NO
8.
To return to time mode, press and hold the BACK button.

Pairing a New Cadence Sensor With Training Computer

Make sure the cadence sensor has been correctly installed. For more information on installing the cadence
sensor refer to the user manual of the cadence sensor or to the video tutorial at
http://www.polar.fi/en/support/video_tutorials.
1.
Go to
>
Menu
Settings
new
and press OK.
2.
Press OK to start the test drive
3.
Press OK and
Searching new cadence sensor
the cadence sensor signal. Rotate the wheel a few times to activate the sensor. The flashing red light in
the sensor indicates that the sensor is activated.
4.
Once the new cadence sensor is identified,
5.
If the search is not successful,
,
further.
Try again? YES / NO
6.
Select
to start the search again.
YES
7.
Select
to cancel the searching.
NO
8.
To return to time mode, press and hold the BACK button.

Pairing a New GPS Sensor With Training Computer

Make sure the GPS sensor has been correctly attached, in an upright position and that your are wearing
the GPS sensor on the same arm as you are wearing your training computer. Also make sure you have
turned the GPS sensor on. For more information on how to set up the GPS sensor refer to the user manual
of the GPS sensor.
1.
Go to
>
Menu
Settings
2.
Searching for new GPS sensor
signal.
3.
Once the new GPS sensor is identified,
4.
If the search is not successful,
Try again? YES / NO
>
>
Sport profiles
Cycling (Bike 1)
is displayed.
Speed sensor found
Speed sensor not found
is displayed.
>
>
Sport profiles
Cycling Bike 1
is displayed.
Cadence sensor found
Cadence sensor not found
is displayed.
>
>
Sport profiles
Running
is displayed. The training computer starts searching for the GPS sensor
GPS sensor found
GPS sensor not found
is displayed.
>
Bike 1 settings
is displayed. The training computer starts searching for
is displayed. Pairing is complete.
or
Other speed sensors interfering. Move
>
Bike 1 settings
is displayed. The training computer starts searching for
is displayed. Pairing is complete.
or
Other cadence sensors interfering. Move
>
>
GPS sensor
Search new
is displayed. Pairing is complete.
or
Other GPS sensors interfering. Move further.
ENGLISH
>
>
Speed sensor
Search
>
>
Cadence sensor
Search
and press OK.
Using a New Accessory
,
41

Advertisement

Table of Contents
loading

Table of Contents