Daily Flight Checks ..........39 Warranty and Repair Policy ........39 Warranty Services ..........40 Compliance Information for the European Union ..41 2010 Official Academy of Model Aeronautics Safety Code ....... 41 E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Fan Unit EFLA1060 60-Amp Pro Switch-Mode BEC Brushless ESC EFLB32004S30 3200mAh 4S 14.8V 30C Li-Po, 13AWG EC3 The Spektrum trademark is used with permission of Bachmann Industries, Inc. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
E-flite S75 servo for the ailerons. If Such things as a foam stand, large piece of bedding you install a smaller servo, you may choose to use the ...
Page 5
While waiting for the epoxy to dry on one wing panel, you can repeat the previous steps to glue the remaining servo mount into the opposite wing panel. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
11. Use string or dental floss to secure a 9-inch (228mm) servo extension to the lead from the aileron servo. 14. Repeat Steps 1 through 13 to install the remaining aileron servo. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 7
3. Use side cutters to trim the pins on the control horn to a length of 1/8-inch (3mm) so they don’t extend through the top of the aileron. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 8
Don’t open the connector too far as it could possibly break the connector. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
17. Repeat Steps 1 through 16 to install the remaining aileron linkage and servo cover. Cut the portions of the letters from the decal sheet to apply to the cover to complete the form of the covered letters. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 10
You also don’t want to sand too fuselage where the wing fits. much and ruin the paint on the fuselage. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 11
9. Apply a thin layer of 15-minute epoxy to the short and long wing rods before you insert them into the wing. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
3. Separate the elevator from the stabilizer. Set the produce the wrong angle when gluing the elevator and hinges aside at this time. stabilizer halves together. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 13
Both measurements must be equal. If not, taping them together. readjust the stabilizer and re-measure until the measurement is the same on both the left and right of the aircraft. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 14
(with a new blade) or a soldering iron for cutting the covering. These will melt the covering and lower the chances of cutting into the wood structure of the stabilizer. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
2. Slide the three hinges into the slots that have been pre-cut into the elevator. Use a paper towel and rubbing alcohol to remove the lines from the stabilizer and fuselage before gluing the stabilizer in position. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Use side cutters to trim down the hinges that fit at the top and center of the rudder as shown. 8. Repeat Steps 1 through 7 to install the remaining elevator. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 17
Hinge point have no epoxy in the knuckle. of rudder Hinge point recessed in control surface E-flite F-86 Sabre 15 DF ARF Assembly Manual...
The pushrod connector will attach to this arm. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 19
Make sure to secure this nut with threadlock or CA. 4. Insert the pushrod connector in the hole. It should move freely in the hole but not have excessive slop. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 20
10. Place 2–3 drops of thin CA in each hole to harden the surrounding wood. This will harden the wood, making the screws more secure. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 21
Don’t open the connector too far as it could possibly break the connector. 1-inch (25mm) 1/16-inch (1.5mm) E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Allow the epoxy to fully a #1 Phillips screwdriver to tighten the screw. cure before proceeding. Use side cutters to trim the excess pushrod wire extending past the pushrod connector. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 23
5. Insert the micro pushrod connector in the hole. It 9. Secure the rudder servo in the fuselage using elevator servo. should move freely in the hole. the screws provided with the servo and a #1 Phillips screwdriver. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
There is a left and right main gear wire. too far as it could possibly break the connector. When positioned correctly the spring coil will face the rear as shown in the photos. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 25
The gear will angle forward Do not tighten the screw at this time. as shown in the photo. Always use threadlock on metal-to-metal fasteners to prevent them from vibrating loose. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Check to make sure the nose gear wire can move freely so the steering servo is not overloaded when trying to steer your aircraft. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
2. Remove the backing from the hook and loop tape on the speed control. Secure the speed control inside the fuselage as shown. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 28
Use hook and loop tape to attach the receiver inside the fuselage as shown in the photo. Cut hole for ESC cooling E-flite F-86 Sabre 15 DF ARF Assembly Manual...
This will prevent you from accidentally looping the tape around the steering linkage wire. 2. Prepare the hook and loop strap by attaching the pieces together using a 2-inch (52mm) overlap as shown. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Note that the fairing faces to the bottom of be determined during assembly. the fan unit. Mounting lug Fan bottom (fuselage top) Fan centerline Mounting lug E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 31
Slot the exhaust tube so it can be slid over 9. Use a #1 Phillips screwdriver to thread a the fan fairing. mounting screw into the four holes for mounting the fan unit. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
2. Slide the exhaust tube into the fuselage, with the wider end of the tube entering the fuselage from the rear. It will “pop” open when it has been inserted fully into the fuselage. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 33
8. Cut four pieces of clear tape using scissors and Use the clear tape supplied with your aircraft to tape the fan access hatch to the fuselage. tape the thrust tube to the fan housing. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Insert the assembly into the fuselage and secure it to the rest in the fuselage using two 2mm x 6mm sheet metal screws and a #1 Phillips screwdriver. Install both assemblies at this time. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
2. Insert the cockpit in the canopy hatch. It is best to insert the front first, then the rear will fit right in. 2. Apply the mating portion of the tape to the bottom of the motor battery as shown. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Mark the location of the battery on the intake tube using a felt-tipped pen so it can be returned to this position if it is removed from your model. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
(10mm) +10% Exponential Aileron Low Rate (80%) 9/32-inch (7mm) Linear Exponential Travel Adjust and Sub-Trims are not listed Down 9/32-inch (7mm) Linear Exponential and should be adjusted according to each individual model and preference. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Happy Landings! direction and with the recommended throws). using a Spektrum radio system. Check all the control horns, servo horns, and clevises to make sure they are secure and in good condition. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than Horizon. Return of any goods by Purchaser must be approved in writing by Horizon before shipment. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon Hobby. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
This does not apply to model aircraft flown indoors. I will not operate model aircraft with metal-blade propellers or with gaseous boosts (other than air), nor will I operate model aircraft with fuels containing tetranitromethane or hydrazine. E-flite F-86 Sabre 15 DF ARF Assembly Manual...
Page 42
Model Aircraft Safety Code. except for the pilot and located at the flightline. I will have completed a successful radio equipment ground-range check before the first flight of a new or repaired model aircraft. E-flite F-86 Sabre 15 DF ARF Assembly Manual...