Accessories; Options/Accessories; Field Installed Options; Tig Welding Accessories - Lincoln Electric RANGER 250 SVM150-A Service Manual

C-2

OPTIONS/ACCESSORIES

FIELD INSTALLED OPTIONS

The following options/accessories are available for
your Ranger 250 from your local Lincoln distributor.
K957-1 HEAVY DUTY, TWO-WHEEL TRAILER FOR
SMALL WELDERS - For road, off-road and in-plant
and yard towing. (For highway use, consult applicable
federal, state and local laws regarding requirements for
brakes, lights, fenders, etc.)
K1737-1 FOUR-WHEEL ALL-TERRAIN UNDERCAR-
RIAGE - For moving by hand.
K1770-1 UNDERCARRIAGE (FACTORY) - For mov-
ing by hand on a smooth surface. One or two gas
cylinders can be mounted on the rear of the undercar-
riage with the installation of K1745-1 Cylinder
Holder(s).
K1739-1 CABLE CARRIER KIT - For use on K1737-1
and K1770-1 Undercarriages.
K1745-1 SINGLE GAS CYLINDER HOLDER - For use
on K1770-1 Undercarriage.
installed on an undercarriage.
K1788-1 ROLL CAGE - Gives added damage protec-
tion.
K886-2 CANVAS COVER - Protects machine when
not in use.
S24647 SPARK ARRESTER - Mounts inside exhaust
pipe.
K702 ACCESSORY KIT - Accessory set includes 35 ft.
(10.7 meters) 2 AWG electrode cable, 30 ft. (9.1
meters) 2 AWG work cable, headshield with No. 12 fil-
ter, GC300 work clamp and Cooltong 300 electrode
holder. Cables are rated at 250 amps, 40% duty cycle.
K857 28 ft. (8.5m) or K857-1 100 ft. (30.4m)
REMOTE CONTROL - Portable control provides same
dial range as the output control on the welder. Has a
convenient 6-pin plug for easy connection to the
welder.
K1690-1 GFCI RECEPTACLE KIT - Includes one UL
approved 120 volt ground fault circuit interrupter duplex
type receptacle with cover and installation instructions.
Replaces the factory installed 120V duplex receptacle.
Each receptacle of the GFCI Duplex is rated at 20
amps. The maximum total current from the GFCI
Duplex is limited to 20 amps. Two kits are required.
K802-N POWER PLUG KIT - Provides four 120 volt
plugs rated at 20 amps each and one dual voltage, full
KVA plug rated at 120/240 volts, 50 amps.
K802-R POWER PLUG KIT - Provides four 120 volt

ACCESSORIES

One or two may be
RANGER 250
plugs rated at 15 amps each and one dual voltage, full
KVA plug rated at 120/240 volts, 50 amps.
T12153-9 50 AMP, 120/240V POWER PLUG -
Provides one dual voltage plug for full KVA power.

TIG WELDING ACCESSORIES

K1783-9 TIG TORCH - For TIG welding with shielding
gas. Includes 25 feet of cable.
K963-2 - Hand Amptrol.
K870 - Foot Amptrol.
NOTE: TIG welding requires a Magnum™ TIG Gun,
appropriate Magnum Parts Kit and argon gas.
SEMIAUTOMATIC FCAW AND MIG
WELDING ACCESSORIES
LN-25 WIRE FEEDER K449 - This portable unit pro-
vides CC/CV for flux-cored arc welding (FCAW) and
metal inert gas welding (MIG). Includes a gas solenoid
and an internal contactor that allows across-the-arc
operation with no control cable. The LN-25 provides a
"cold" electrode until the gun trigger is pressed. For
voltage control at the feeder, a K444-1 Remote Voltage
Control Kit or K857 Remote Control is required. Refer
to connection instructions later in this section.
LN-7 OR LN-8 WIRE FEEDER - Semiautomatic, con-
stant speed wire feeders.
NOTE: Gas-shielded welding requires a Magnum Gun.
Gasless welding requires an Innershield Gun.
LN-742 WIRE FEEDER - A semiautomatic wire feeder
with "cold" electrode. Refer to connection instructions
later in this section.
MAGNUM SPOOL GUN (K487-25) - A lightweight,
semiautomatic wire feeder for aluminum welding with
argon gas. Has built-in remote wire speed control in
the handle. Requires the K488 SG Control Module.
Refer to connection instructions later in this section.
SG CONTROL MODULE (K488) - Controls wire speed
and gas flow. Provides the required control interface
between the Ranger 250 and the K487-25 Magnum
Spool Gun. Requires the K691-10 Input Cable.
K444-1 REMOTE VOLTAGE CONTROL - Provides
voltage adjustment control at the feeder. Includes 25
feet of cable.
K126-2 INNERSHIELD GUN - For gasless welding.
Includes 15 feet of cable.
K470-2 MAGNUM GUN CONNECTOR KIT - For gas-
shielded welding.
K466-1 MAGNUM GUN CONNECTOR KIT - For con-
necting the Magnum 300 MIG Gun to the feeder for
gas-shielded welding.
C-2