Off - Roland V-440HD Owner's Manual

Menu Parameters
13. System
The V-440HD's system settings are made here.
Parameters
13- 1. System Frame Rate
13- 2. SD Deinterlacer
13- 3. SD Input Sync Threshold
13- 4. SD V-FdrCaribrate A
13- 5. SD V-FdrCaribrate B
13- 6. HD/RGB V-FdrCaribrate C
13- 7. HD/RGB V-FdrCaribrate D
13- 8. REMOTE Baudrate
13- 9. HD Seamless Delay Time
13- 10. SD Seamless Delay Time
13- 11. HD On Screen Display
13- 12. Tally Signal
13- 13. SD Previewout Select
13- 14. Panel Operation Mode
13- 15. Input Sw LED Color
13- 16. Double Click Short Cut
13- 17. Autotake Sw Motion
13- 18. All Data Transmit
13- 19. System Reset
13- 20. Memory Protect
Adjusting the SD Input Sync Level
The sync level of the SD signal output by some SD video devices may be lower than standard values, preventing adequate synching
when the V-440HD is set to factory default values. If this occurs, you may be able to achieve synchronization by adjusting the "13-3.
SD Input Sync Threshold" parameter.
Adjusting the Video Faders
Continued use of the video faders and transport of the V-440HD may make adjustments to the faders necessary. In such cases, use
the following procedure to make the adjustments.
[Adjusting the Video Fader (SD)]
1. Display the menu.
2. Select "4. SD V-Fdr Calibrate A" under "13. System."
3. Tilt the video fader (SD) to the A-BUS.
4. The message "Are You Sure?" appears; select "Yes."
5. Select "5. SD V-Fdr Calibrate B."
6. Tilt the video fader (SD) to the B-BUS.
7. The message "Are You Sure?" appears; select "Yes."
* Use the same procedure to adjust the video fader (HD/RGB), using "Video Fader Calibrate C" and "Video Fader Calibrate D."
64
Explanation
Switches between NTSC and PAL
SD section I/P conversion function
SD input sync level adjustment
SD video fader adjustment
SD video fader adjustment
HD/RGB video fader adjustment
HD/RGB video fader adjustment
REMOTE bit rate setting
Delay time when C-BUS (D-BUS) channel buttons are
used
Delay time when A-BUS (B-BUS) channel buttons are
used
Displays HD/RGB output in menu
Mode for signals output from TALLY terminals
Video output from SD PREVIEW OUT connector
Switches the panel operation mode
Sets the colors of the channel button indicators
Determines whether menus appear when buttons are
double-clicked
Operation performed when AUTO button is pressed
Transmits the V-440HD's settings from the REMOTE
connector
Resets the system settings to the original factory settings
Memory Protect function
Values
60 - NTSC, 50 - PAL
Off, On
-48– +79
* Refer to "Adjusting the Video Faders."
* Refer to "Adjusting the Video Faders."
* Refer to "Adjusting the Video Faders."
* Refer to "Adjusting the Video Faders."
9600bps, 19200bps
0–50 (Field)
0–50 (Field)
On, Off
Type1, Type2, Type3, Type4, Type5, Type6
Preview Out, PGM Out
A/B Mode, PGM-PST Mode
PGM=YEL:PRV=GRN
PGM=YEL:PRV=RED
PGM=RED:PRV=GRN
PGM=RED:PRV=YEL
PGM=GRN:PRV=RED
PGM=GRN:PRV=YEL
Off, On
Change, Continue, Jump, Cancel
* Refer to "Saving the V-440HD's Settings to a
Computer" (p. 48).
—
Off, On