Table of Contents
Advertisement
Menu Parameters
*
For more on menus, see p. 24.
1. HD/RGB Output
Settings for the final output are made here.
Parameters
1- 1.
Output Format (1080i) Sw
1- 2.
Output Format (720p) Sw
1- 3.
Output Format (RGB) Sw
1- 4.
Output Format Sw Lock
1- 5.
Zooming
1- 6.
Bright
1- 7.
Contrast
1- 8.
Saturation
1- 9.
Red
1- 10.
Green
1- 11.
Blue
1- 12.
Output Fade Mode
1- 13.
Output Fade Color
1- 14.
Output Fade Sw Motion
1- 15.
Test Pattern Select
1- 16.
HD/RGB Reset
About the Final Output Format
You can select from the following formats for use with the final output.
Component
[NTSC]
1080/60i
720/60p
480/60p
480/60i
*
The selectable component format changes as above depending on the setup for "1. System Frame Rate" under "13. System."
*
The frame rate of 59.94 is shown as 60 in the menu of this unit.
*
RGB units are [horizontal (pixels) x vertical (lines) / frame rate (Hertz)].
About the Final Output Fade Control
There are two final output fade modes (p. 23), which can be changed as needed.
[1-12. Output Fade Mode Settings and Function of Each Controller]
OUTPUT FADE Button
TIME Knob
OUTPUT FADE Button Operational Mode
You can select operation mode of fade in/out using OUTPUT FADE button.
[1-14. OutputFade SW Motion Settings and Operation When the OUTPUT FADE Button is Pressed]
Mode
Change (Initial setting)
Continue
Jump
Cancel
*
For more on these parameters, refer to "Switching Buses with the AUTO Button (HD/RGB)" (p. 30).
58
Explanation
Video format assigned to OUTPUT FORMAT (1080i) button
Video format assigned to OUTPUT FORMAT (720p) button
Video format assigned to OUTPUT FORMAT (RGB) button
OUTPUT FORMAT button lock
Final output scaling adjustment
Final output brightness adjustment
Final output contrast adjustment
Final output saturation adjustment
Final output red adjustment
Final output green adjustment
Final output blue adjustment
Final output fade control adjustment
Final output fade color setting
Selects the operation mode when OUTPUT FADE button is
pressed
Selects the Test Pattern to output
Resets the above settings to the original factory settings
RGB
[PAL]
1366x768/60
1080/50i
1366x768/75
720/50p
1280x1024/60
576/50p
1280x768/75
576/50i
1280x768/60
1024x768/75
Auto
Fades in/out according to value set with TIME knob
Sets Fade-in/Fade-out time for final output
When Pressed During Operation
Stops
Stops
Forces execution of the operation
Cancels the operation and returns you to the previ-
ous step
Values
* Refer to "About the Final Output Format."
* Refer to "About the Final Output Format."
* Refer to "About the Final Output Format."
Off, On
80.0–120.0
-64– +64
-64– +64
-64– +64
-64– +64
-64– +64
-64– +64
Auto, Manual
* Refer to "About the Final Output Fade
Control"
Black, White
Change, Continue, Jump, Cancel
* Refer to "OUTPUT FADE Button
Operational Mode."
Off, 75% Color Bar, 100% Color Bar
—
1024x768/60
800x600/75
800x600/60
640x480/75
640x480/60
Manual
Indicates the fade status (no operation is executed,
even when button is pressed)
- Lights when fade is completed
- Flashes while fade is in progress
- Off when no fade is being performed
Controls fade-in/fade-out time
Pressed During Operation and Pressed Again
Returns in response to level
Continues in same direction as that before stopping
—
—
Advertisement
Chapters
Table of Contents
