Panasonic AW-HE130W Operating Instructions Manual page 74

Web screen configurations (continued)
Internet mode (over HTTP)
This setting is selected when transmitting H.264 images over the
Internet.
H.264 images can be transmitted using the same broadband router
settings as when transmitting JPEG images.
Setting value:
On The H.264 images and audio are transmitted using the HTTP
port. For details on setting the HTTP port number, refer to
page @@.
Off The H.264 images and audio are transmitted using the UDP
port.
Factory settings: Off
<NOTE>
• When "On" is set, only "Unicast port (Port number settings: AUTO)"
can be selected as the "Transmission type" setting.
• When "On" is set, it takes a few seconds before the H.264 images
are displayed.
• When this is set to [On], H.264 images may not appear depending
on the number of users accessing the unit at the same time and
whether audio data exists.
• When this this set to [On], access will be limited to IPv4.
Image capture size
Select the resolution for H.264 images.
Selectable options will vary depending on the selected resolution
setting.
Setting value:
H264(1) 1920×1080
1280×720
H264(2) 1920×1080
1280×720
640×360
320×180
160×90
H264(3) 1280×720
640×360
320×180
160×90
H264(4) 1280×720
640×360
320×180
160×90
Factory settings:
H.264(1): 1920×1080
H.264(2): 640×360
H.264(3): 320×180
H.264(4): 160×90
Transmission priority
Set the transmission mode for H.264 images.
Setting value:
Constant bit rate Transmits H.264 images at the bit rate specified
in [Max bit rate (per client)].
Frame rate Transmit H.264 images at the frame rate specified
in [Framerate].
Best effort Transmit H.264 images at a variable bit rate
between the maximum and minimum specified in
[Max bit rate (per client)], according to the network
bandwidth.
Advanced VBR Transmit H.264 images at the frame rate specified
in [Framerate]. Images will be transmitted so
that the average transmission volume during the
duration specified in [Control time period] will be
the bit rate specified in [Max bit rate (per client)].
Factory settings: Frame rate
<NOTE>
• When [Transmission priority] is set to [Frame rate] or [Advanced
VBR], the number of users that can connect may decrease.
74
Framerate
Set the frame rate for H.264 images.
Setting value:
For 60Hz:
5fps / 15fps / 30fps / 60fps
1 1 1
* * *
For 50Hz:
5fps / 12.5fps / 25fps / 50fps
1 1 1
* * *
Factory settings:
For 60Hz: 30fps
For 50Hz: 25fps
*
1
The frame rate is limited by the [Max bit rate (per client)] setting.
The actual frame rate may be lower than the specified value.
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Frame rate] or [Advanced VBR].
• [H.264(1)] is fixed at 60 fps (for 60 Hz) and 50 fps (for 50 Hz).
60 fps (for 60 Hz) and 50 fps (for 50 Hz) cannot be selected for
[H.264(2)] to [H.264(4)].
Burst tolerance level
Select how much more than the [Max bit rate (per client)] value to
allow for the H.264 bit rate.
Setting value:
High / Middle /Low
Factory settings: Low
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Advanced VBR].
Control time period
Select the duration for which the H.264 bit rate will be controlled.
Images will be transmitted so that the average transmission volume
during the duration specified will be the bit rate specified in [Max bit
rate (per client)].
Setting value:
1h 1 hours
6h 6 hours
24h 1 day (24 hours)
1 week 1 week
Factory settings: 24h
<NOTE>
• This setting is only enabled when [Transmission priority] is set to
[Advanced VBR].
1
*
1
*