Setting Each Pedal Functions To Individual Patches (Assign) - Roland GT-100 Owner's Manual

Setting Each Pedal Functions to
Individual Patches (Assign)
You can set the [PHRASE LOOP] Pedal, [ACCEL/CTL], [EXP] pedal,
EXP PEDAL SW and external pedals (footswitch and expression
pedal) connected to the rear panel's SUB CTL 1, 2/SUB EXP jacks for
each individual patch. You can save up to eight separate settings
per patch (using Assign numbers 1 through 8) that determine what
parameters are controlled by which pedals.
* If you want to use the [PHRASE LOOP] pedal with the
assignment you specify, you must turn "PHRASE LOOP PEDAL
FUNC" (p. 40) off. For other pedals, you must set "PREFERENCE"
(p. 41) to "PATCH. "
* You can specify the individual parameter that will be controlled
by each pedal.
1.
Press the [CTL/EXP] button .
2.
Turn knob [4] to select "ASSIGN 1–8 . "
3.
Use knobs [5]–[8] to select the desired settings .
ASSIGN COMMON
Parameter Value
Page 1
[8] INPUT SENS
0–100
Explanation
This adjusts the input sensitivity
when INPUT LEVEL is selected for
SOURCE.
Pedal Settings (Control/Expression)
ASSIGN 1–8
Parameter Value
Page 1
ASSIGN ON/
[5]
OFF, ON
OFF
EXP PEDAL
EXP PDL SW
P.LOOP PEDAL
ACC/CTL PDL
SUB EXP PDL
SUB CTL1 PDL
[6] SOURCE
SUB CTL2 PDL
INT PEDAL
WAVE PEDAL
INPUT LEVEL
CC#1–#31
CC#64–#95
MOMENT
[7] SOURCE MODE
TOGGLE
Page 2
TARGET This selects the parameter to be changed.
[5]
CATEGORY
For details on all parameters, download the "GT-100
Parameter Guide" (PDF file) located under "GT-100"
in the list of "Owner's Manuals" on the Roland
[6] TARGET
website (http://www.roland.com/support/en/).
This sets the minimum value for the range in
which the parameter can change. The value differs
[7] TARGET MIN
depending on the parameter assigned for TARGET
parameter.
This sets the maximum value for the range in
which the parameter can change. The value differs
[8] TARGET MAX
depending on the parameter assigned for TARGET
parameter.
Page 3
[5] ACT RANGE LO 0–126
[6] ACT RANGE HI 1–127
Explanation
Turns the ASSIGN 1–8 on/off.
* This setting is not saved along
with the quick settings.
Assigns the GT-100's built-in [EXP]
pedal.
Assigns the EXP pedal switch.
Assigns the GT-100's [PHRASE
LOOP] pedal.
Assigns the [ACCEL/CTL] pedal.
Assigns the external expression
pedal (such as the separately
available EV-5) connected to the
SUB CTL 1, 2/SUB EXP jack.
Assigns the external footswitch
(FS-5U, FS-6; available separately)
connected to the SUB CTL 1, 2/SUB
EXP jack.
Assigns the external foot switch
(FS-5U, FS-6; available separately)
connected to the SUB CTL 1, 2/SUB
EXP jack.
Refer to "Virtual expression pedal
system (Internal Pedal / Wave
Pedal)" (p. 39))
Refer to "Virtual expression pedal
system (Internal Pedal / Wave
Pedal)" (p. 39)
The assigned target parameter
will change according to the input
level.
Control Change messages from an
external MIDI device.
Control Change messages from an
external MIDI device.
The normal state is Off (minimum
value), with the switch On
(maximum value) only while the
footswitch is depressed.
The setting is toggled On
(maximum value) or Off (minimum
value) with each press of the
footswitch.
You can set the controllable range
for target parameters within the
source's operational range. Target
parameters are controlled within
the range set with ACT RANGE LO
and ACT RANGE HI. You should
normally set ACT RANGE LO to 0
and ACT RANGE HI to 127.
37