Table of Contents
Advertisement
2.0 Operating Instructions
2.1 Operating facilities
l Start-/stop rotary switch - I/O (2).
l Trigger (4a) with lock (4b).
2.2 Connection
1. Unwind the high pressure hose completely and
press the nipple into the spray handle. NOTE:
Only use one extension hose of max. 7 m.
IMPORTANT! To ensure that the unwinding and
winding up of the high pressure hose is only done
when the machine is relieved of pressure, only
tend the hose winder when the spray handle is
detached.
2. Mount the nozzle or any other equipment you
want to use.
Note: When attaching to the snap connector, the
pawl on the side of the connector should come
out again. Press the pawl to detach the equipment.
3. Connect the machine to the water and power
supplies.
2.3 Start
1. Check that the machine is in vertical position.
2. Activate trigger and let the water run out until any
air has escaped from the inlet hose.
3. Turn the start/stop switch (2) to pos. I.
2.4 Operation
1. The spray lance is affected by a thrust
during operation - therefore always hold
it firmly with both hands.
2. Point the nozzle at the ground.
3. Activate the trigger of the spray handle (4a).
4. Always adjust the distance and thus the pressure
of the nozzle to the surface which is to be cleaned.
NOTE: Do not cover the machine during operation.
If the machine is left or not used for 5 minutes, it
must be switched off on the start/stop switch.
2.5 Suction mode
The machine can take in water from a rain water
butt as an example. The water inlet hose must not
be too long, approx. 5 m.
1. Make sure that the water butt is not placed on a
lower level than the machine.
2. Attach the water inlet hose to the machine and
place the other end of it in the water butt.
3. Start the machine.
4. Detach the spray lance and activate the trigger of
the spray handle. Keep the trigger activated until
water has come out for approx. 15 seconds.
5. Remount the spray lance and the machine is
ready for operation.
Operating Instructions
NOTE: The internal filter of the machine is not
intended for the filtration of large quantities of im-
purities. If the water contains leaves, sand or the
like, an external suction filter should be mounted.
For further information, please contact your nearest
ALTO distributor.
2.6 End of operation
1. Shut off the water supply and activate the trigger
(4a) to relieve the machine of pressure.
2. Stop the machine by turning the start/stop switch
(2) to pos. O.
3. Disconnect the plug from the socket.
4. Disassemble spray handle and high pressure
hose. Press the blue button and pull the hose at
the same time.
5. Wind up the high pressure hose. Lead the hose
from the left to the right and back again. If the
hose sticks, the cover of the winder can be remo-
ved to make sure that the hose has been winded
up correctly in two layers.
6. Place spray handle, nozzles and other accesso-
ries in the holders/store room on the machine.
Concerning storage, please refer to section 5.0.
3.0 Accessories
Equipment
Only use original accessories.
Nozzles
Tornado
(7)
®
Powerspeed
(8)
®
Car nozzle (9)
Undercarriage
nozzle (10)
Attached with the „Click and
Clean" connector system.
Stored on the machine.
Universal nozzle. Max. effect
at a distance of approx. 7 cm.
Nozzle with rotating jet
for stubborn dirt on hard
surfaces. Max. effect at a
distance of approx. 10 cm.
Special nozzle for enamelled
surfaces. Marked with a car.
Optimal distance: 30 - 50 cm.
90
angled special
o
nozzle for
undercarriage and
wheel arches. Inte-
grated guide shoes.
5
Hide quick links:
Advertisement
Table of Contents
