Table of Contents
Advertisement
L390E / HZI390E Gas Insert
MODELS: L390E-NG2 / L390EB-NG2 Natural Gas
HZI390E-NG2 / HZI390EB-NG2 Natural Gas
WARNING:
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to
this manual. For assistance or additional information consult
an authorized installer, service agency or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapours and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by an authorized
installer, service agency or the gas supplier.
Tested by:
919-234b
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
L390E-LP2 / L390EB-LP2 Propane
HZI390E-LP2 / HZI390EB-LP2 Propane
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you
supplier, call the fi re department.
Owners &
Installation Manual
Liberty L390E
Horizon HZI390E
www.regency-fi re.com
cannot reach your gas
04/28/14
Advertisement
Table of Contents
Related Manuals for Regency L390E
Summary of Contents for Regency L390E
- Page 1 Owners & L390E / HZI390E Gas Insert Installation Manual Liberty L390E Horizon HZI390E www.regency-fi re.com MODELS: L390E-NG2 / L390EB-NG2 Natural Gas L390E-LP2 / L390EB-LP2 Propane HZI390E-NG2 / HZI390EB-NG2 Natural Gas HZI390E-LP2 / HZI390EB-LP2 Propane WARNING: FOR YOUR SAFETY Improper installation, adjustment, alteration, service or What to do if you smell gas: maintenance can cause injury or property damage.
- Page 2 The Regency Gas Insert Series of hand crafted appliances has been designed to provide you with all the warmth and charm of a fi replace, at the fl ick of a switch. The models L390E / HZI390E of this series have been approved by Warnock Hersey for both safety and effi...
-
Page 3: Dimensions
(76mm) 21-5/8” (549mm) 15-3/4” 12-1/8” (400mm) (308mm) 2-1/4” (57mm) 27-1/2” (699mm) 10-7/8” 26-1/8” (276mm) (664mm) 3” (76mm) 25-3/4” (654mm) 17” 19-1/2” 14-3/4” 20” (432mm) (495mm) (375mm) (508mm) 24-1/8” 15-3/4” (613mm) (400mm) 39-7/8” (1013mm) L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 4 DIMENSIONS 39-15/16” (1014mm) 35-15/16” (911mm) Dimensions w/4 sided Faceplate 44" 1118mm 8 " 910mm Dimensions w/Oversized Faceplate 38-1/8” (968mm) 17-1/4” (438mm) Dimensions w/Full Screen Doors L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 5: Table Of Contents
............51 Fan installation / removal..........20 Wiring Diagram ............22 PARTS LIST Profl ame Remote system gtm (L390E / HZI390E) ..22 AC power adaptor installation (for surefi re systems) ...23 Main Assembly ............53 Profl ame remote system GTMF with fan (L390EB / low profi... -
Page 6: Safety Label
SAFETY LABEL This is a copy of the labels that accompany each L390E Gas Insert. We NOTE: Regency units are constantly being improved. Check the have printed a copy of the contents here for your review. label on the unit and if there is a difference, the label on the unit is the correct one. - Page 7 SAFETY LABEL This is a copy of the labels that accompany each HZI390E Gas Insert. NOTE: Regency units are constantly being improved. Check the We have printed a copy of the contents here for your review. label on the unit and if there is a difference, the label on the unit is the correct one.
-
Page 8: Requirements
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 9: Installation
IN THE SAME AREA AS THE APPLI- INSTRUCTIONS ANCE. TODDLERS, YOUNG CHILDREN AND OTHERS MAY BE SUSCEPTIBLE The L390E / HZI390E Gas Inserts must be installed TO ACCIDENTAL CONTACT BURNS. A in accordance with these instructions. Carefully read PHYSICAL BARRIERS IS RECOMMEND- all the instructions in this manual fi... -
Page 10: Important Message
fi replace insert or clothing ignition. Young children should Log Set: Ceramic fi bre, 6 per set - L390E only and cannot be used for burning wood or be carefully supervised when they are in solid fuels unless all original parts have been the same room as the appliance. -
Page 11: Installation Checklist
(Refer to section "Flue Liner Installation.") The minimum fi replace clearances & dimensions for the Regency gas insert are shown in the 4) Slide the unit half way into the fi replace. following diagrams: 5) Pull the vent connector plate through the tapered brackets and fasten to the front plate. -
Page 12: Minimum Clearances To Combustibles
Note: All material used must be completely non-combustible. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 13: Gas Connection
Periodically check that the vent is unrestricted. Masonry chimneys may take various contours which the fl exible liner will accommodate. However, keep the fl exible liner as straight as possible, avoid Gas & Electrical Connections unnecessary bending. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 14: Flue / Vent Installation
Properly installed Flue Connector Plate WaRninG: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 15: Levelling Leg Adjustment
LEVELLING LEG ADJUSTMENT The L390E / HZI390E inserts are equipped with 4 levelling legs that are accessible while the appliance is in its fi nal installation position. The unit can be adjusted up to 2" (51mm). The faceplate must not be installed to do this adjustment, if installed, remove faceplate. -
Page 16: Air Shutter Adjustment
The L390E / HZI390E is equipped with an air shutter that is accessible from outside the fi rebox and can be adjusted during operation. -
Page 17: Conversion From Ng To Lp
M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that the screw threads are cross threaded or stripped, replace the valve The valve in the L390E is attached using 2 screws and 2 hooks located assembly. - Page 18 Verify both the correct fl ame and pilot appearance. 14) See Gas Pipe Pressure Testing in manual. 15) Adjust aerations settings - see Air Shutter Adjustment section in the manual. Installer Notice: These instructions must be left with the appliance L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 19: High Elevation
6) When fi nished reading manometer, turn off the gas valve, disconnect the hose and tighten the screw (clockwise) with a 1/8" fl at screwdriver. Note: Screw should be snug, but do not over tighten. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 20: Profl Ame Remote System Gtmf With Fan (L390Eb / Hzi390Eb)
Caution: Ensure that the wires do not touch any CAUTION: Label all wires prior to disconnection hot surfaces and are away from sharp edges. when servicing controls. Wiring errors can cause improper and dangerous operation. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 21: Fan Wiring Diagram
INSTALLATION FAN WIRING DIAGRAM FOR USE WITH THE OPTIONAL 396-917 FAN FOR L390E/HZI390E) Grounding Ground wire Lug Detail Ground from fan Lockwasher Star washer Neutral Green Live Star washer Ground Ground wire 120V AC from power cord Black Black Rotary Speed... -
Page 22: Optional Wall Thermostat Installation
3) Connect one thermostat lead to female connector, using male spade con- nector - see pic below. When complete turn remote receiver to the ON position. Unit will now operate using the wall thermostat. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 23: Glass Crystal / Ceramic Spa Stone Installation
Natural River Pebbles shown surrounding the a Horizon Burner Glass Crystals shown surrounding the Burner Glass Crystals shown on Burner and Firebox Floor For Units HZI390E, HZI540E DO NOT block pilot area with glass crystals L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 24 INSTALLATION CAUTION DO NOT place spa stones over pilot and burner ports. No spa stones in this area. L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 25: Hzi390E Optional Log Set Installation
2. Both HZ540 & HZ390 Units. Sweep glass aside (if already installed) to install Rear Log Bracket, clip on to rear of the burner as shown below. 9-1/4" Position Log 2 Rear Log Bracket L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 26 540 Pin Landing 390 Pin Landing 12. Adjust aeration setting to fully open (manual for detailed instruc- tions) Note: Logs to be installed in NG units only. Line up pin locator and pin, Logs 5,4 L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 27: L390E Log Set Installation
4) Position Log 2 on burner pins located in the right rear corner. When seated, Log 2 should sit fl at and not rock. Log 1 pins on burner tray 2) Identify corresponding locators on bottom of Log 1 - see below. Log 1 locators L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 28 7) When installed - ensure the air gap at the rear of the log is maintained - as indicated by arrow below. Log 5 - correct position R Log 5 - correct position L Log 5 - correct position installed L390E-2 / HZI390E-2 Direct Vent Gas Insert...
- Page 29 L390E 11) Match up pin on Log 5 with locator on Log 6 as shown below. 12) Rest Log 6 in notch on Log 3—as shown below. Final Install Notch in Log 3 L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 30: Standing Pilot
INSTALLATION STANDING PILOT The L390E / HZI390E use a heat exchanger and effi cient combustion technology to provide extreme heating effi ciencies. The more effi cient an ap- ADDING THE HEAT EXCHANGER RETURN pliance becomes, the lower the fl ue gas temperatures becomes. -
Page 31: Brick Panel Installation
Liner Rear. The side Liner will hold the rear Liner in place. Install the Fire- box Liner Left the same way you installed the Firebox Liner Right. Both side liners should be just slightly back from the front edge of the Firebox. Brick Panel Installation L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 32: Enamel Panel Installation
fi t between the fi rebox liner rear and the fi rebox. You may have to push the liner against the fi rebox as you push it rearward. Panel retainers HZI540PB *Insulation panels not shown in this diagram Installing Enamel Panels L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 33: Glass Door Removal / Installation
6) Pull the bottom of the door towards you until the door is angled away from the fi rebox by about 30°. Lift the door up and over the upper door hooks. 7) To install the glass door - reverse steps. Glass Door Cleaning & Removal L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 34: Sided Low Profi Le Faceplate Installation
Note: Faceplate may be installed after the unit is in it's fi nal position. 3) Install Low Profi le faceplate backing plate and secure to the unit with 4 Trim screws in locations shown below. Final Install L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 35 Note: Faceplate may be installed after the unit is in it's fi nal position. Trim 3) Install Low Profi le faceplate backing plate and secure to the unit with 4 screws in locations shown below. Final Install L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 36: Oversize Faceplate Installation
1. Install Low Profi le faceplate backing plate and secure to the unit with 4 screws in locations shown below. Trim 2. Install front faceplate and secure to the unit with 4 screws in locations shown below. Final Install L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 37: Optional Hearth Trim Installation
Hearth Trim is an option that can be used to fi nish off the installation when the bottom of the fi replace is higher than the hearth or to raise the fi replace. ** If no screw holes are present. 1) For units L390E/HZI390E/L540E/HZI540E–remove 4 screws in locations shown below to remove outer faceplate. -
Page 38: Optional Screen Installation
Locations shown in the diagrams below. Tabs 2) Secure the screen by placing provided magnets between the back of the screen and the unit in locations shown below. 3) To remove - reverse steps. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 39: Optional Full Screen Door Installation
. The tabs should be fl ush with the underside of the top lip of the back plate. Top of backing plate 3) Install the optional full screen to the unit by securing with 4 screws in locations shown below. Final Install L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 40: Operating Instructions
After the unit has been turned off and the unit cooled to below a useful to turn off the pilot. heat output range the fan will shut off automatically. Glass Door Cleaning & Removal L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 41: Normal Operating Sounds Of Gas Appliances
Appuyez sur le bouton ON / OFF Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction pour plus de détails. DO NOT REMOVE THIS INSTRUCTION PLATE 918-628b L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 42: Maintenance Instructions
fl ames: 1 fl ow- ing around the thermopile and 1 around the thermocouple, and 1 fl owing across the rear of the burner (it does not have to be touching the burner). Window Glass Door Components L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 43: Pilot Adjustment
NOTE: Improper positioning of logs may create carbon build-up and will alter the unit’s performance which is not covered under warranty. GLASS GASKET If the glass gasket requires replacement use glass gasket for the Flush Front (Part # 936-112). L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 44: Glass Crystal Burner Removal / Installation - Hzi390Eb
** Do not to install glass or other media over or in front of the Pilot Provision as shown. Important: Do not to install glass or other media in this area, as this will black the path of the pilot to the burner. L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 45: L390E /L390Eb Ceramic Burner Removal / Installation
MAINTENANCE L390E /L390EB CERAMIC BURNER REMOVAL / INSTALLATION REMOVAL INSTALLATION 1) Remove left/right fi ller sections - see below. Care must be taken when installing the burner into the fi rebox. Discard fi llers only if inner panels are being installed. -
Page 46: Fan Maintenance - With Gtmf Remote Control
1/4" spade connectors to the fan terminals. Disconnect the ground lug to the fan using the screw provided. Strain Relief Power Cord Fan Controller Wire Retainer Fan Wire Harness Fan Terminals Ground Wire Fan Mounting Bracket Diagram 2 L390E-2 / HZI390E-2 Direct Vent Gas Insert... -
Page 47: Valve Replacement
3) Disconnect the Pressure Regulator cable. 7) Remove both Screws that secure the Gas Valve Mounting brackets, both sides. Pressure regulator cable 4) Disconnect the Gas Orifi ce supply line from the outlet of the Gas Valve. L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 48 15) Reconnect the gas and electrical supply to the unit. Once the unit has be re-fi red, use a soapy water mixture to check all fi ttings and gas sup- ply lines for gas leaks. L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 49: Parts List
Remote Control (Hand held) GTM 910-592 Remote Control (Hand held) GTMF 904-943 Gas supply line (outlet to burner orifce) 911-093 10 ft. extension cord (EB units) 911-137 Pilot Hood Holding Clip Part Not Shown L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 50 PARTS LIST L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 51: Low Profi Le Faceplate
3 sided low profi le faceplate - Iron grey 397-982 Oversize faceplate - Sunset bronze 397-984 Oversize faceplate - Metallic black 397-985 Oversize faceplate - Iron grey 397-926 4 sided faceplate (custom sizes) - Metallic black L390E-2 / HZI390E-2 Direct Vent Gas Insert... - Page 52 NOTES L390E-2 / HZI390E-2 Direct Vent Gas Insert...
- Page 53 NOTES L390E-2 / HZI390E-2 Direct Vent Gas Insert...
- Page 54 NOTES L390E-2 / HZI390E-2 Direct Vent Gas Insert...
-
Page 55: Warranty
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from unauthorized service persons or dealers. - Page 56 Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Horizon HZI390E Liberty L390E ® Regency and Regency Horizon, are trademarks of FPI Fireplace Products International Ltd. Printed in Canada © Copyright 2014, FPI Fireplace Products International Ltd. All rights reserved.