Table of Contents
Advertisement
Quick Links
LIBERTY L676E Gas Fireplace
WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.
Tested by:
918-621a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
www.regency-fi re.com
TM
MODELS: L676E-NG Natural Gas L676E-LP Propane
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Owners &
Installation Manual
Unit requires 120V to
operate. See "Wiring Diagram"
section in manual for more
details. Receptacle is included
with manual package.
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fi re department.
03/14/08
Advertisement
Table of Contents
Related Manuals for Regency LIBERTY L676E-LP
Summary of Contents for Regency LIBERTY L676E-LP
- Page 1 Owners & LIBERTY L676E Gas Fireplace Installation Manual Unit requires 120V to operate. See “Wiring Diagram” section in manual for more details. Receptacle is included with manual package. MODELS: L676E-NG Natural Gas L676E-LP Propane FOR YOUR SAFETY WARNING:...
-
Page 2: Manufactured Mobile Home Requirements
To the New Owner: Congratulations! ® You are the owner of a state-of-the-art Gas Fireplace by REGENCY . The L676E has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. -
Page 3: Table Of Contents
Allowable Horizontal Terminations .......19 WARRANTY Venting Arrangements ..........22 Allowable Vertical Terminations ......22 The Warranty: Limited Lifetime ........47 Unit Installation with Horizontal Termination ....23 Unit Installation with Vertical Termination ....24 Horizontal Termination with Flex Vent System ....25 ® Regency L676E Direct Vent Gas Fireplace... -
Page 4: Safety Label
® NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. -
Page 5: Requirements
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. Regency ® L676E Direct Vent Gas Fireplace... -
Page 6: Unit Dimensions
UNIT DIMENSIONS Regency ® L676E Direct Vent Gas Fireplace... -
Page 7: Installation
OR CLOTHING IGNITION. appliance be modifi ed. Parts that have to be removed for servicing should be replaced 9) Test Gas Pressure (Refer to "Gas Pipe prior to operating this appliance. Pressure Testing" section). Regency ® L676E Direct Vent Gas Fireplace... -
Page 8: Manufactured Mobile Home Additional Requirements
3) The L676E Direct Vent Gas Fireplace can be installed in a recessed position or framed out into the room as in A, B, C and D. See Diagram 1. Regency ® L676E Direct Vent Gas Fireplace... -
Page 9: Clearances
Fire hazard is an extreme risk if these clearances (air space) to combustible materials are not adhered to. It is of greatest importance that this fi replace and vent system be installed only in accordance with these instructions. Regency ® L676E Direct Vent Gas Fireplace... -
Page 10: Mantel Clearances
"heat resistant" or the paint may discolour. MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram: MANTEL LEG L676 UNIT Non-combustible Facing 9" (229mm) Allowable mantel leg projection 11" (279mm) Side wall 15” (381mm) Regency ® L676E Direct Vent Gas Fireplace... -
Page 11: Framing & Finishing
3) The unit does not have to be completely enclosed in a chase. You must maintain clearances from the vent to combustible materials: See "Clearances" section. Combustible materials can be laid against the side and back standoffs and the stove base. Diagram 2 Non-Combustible Requirements Regency ® L676E Direct Vent Gas Fireplace... -
Page 12: Unit Assembly Prior To Installation
fi replace top been installed. line up. 3) Attach the standoff securely to the top with 2 screws per standoff (on opposite corners). Side Nailing Strips shown folded out. Regency ® L676E Direct Vent Gas Fireplace... -
Page 13: Venting Introduction
3) Adjust the vent restrictor plate to the required vent restrictor position as per the diagrams shown. 4) Once the vent restrictor plate is in the required position, secure with screws. Regency ® L676E Direct Vent Gas Fireplace... -
Page 14: Exterior Vent Termination Requirements
INSTALLATION EXTERIOR VENT TERMINATION REQUIREMENTS Regency ® L676E Direct Vent Gas Fireplace... -
Page 15: Venting Arrangements
INSTALLATION VENTING ARRANGEMENTS HORIZONTAL TERMINATION (FLEX) Regency ® Direct Vent System These venting systems, in combination with the L676E, have been tested and listed as a direct vent heater system by Intertek. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram from the "Exterior Vent Termination Locations" section. -
Page 16: Rigid Pipe Venting Systems
Direct Vent GS and Selkirk Direct-Temp. AstroCap XL is a proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. Regency ® L676E Direct Vent Gas Fireplace... -
Page 17: 5" X 8" Rigid Pipe Cross Reference Chart
58DVA-ES - N/A from FPI Wall Thimble, Black 58DVA-WT 1247 5DT-WT 5DWT Wall Thimble Support Box/Ceiling Support 58DVA-DC - N/A from FPI Firestop Spacer 58DVA-FS 1263 5DT-FS 5DFS Trim Plate, Black 58DAV-WFS 1242 5DT-TP 5DCP Regency ® L676E Direct Vent Gas Fireplace... - Page 18 NOTE: Horizontal runs of vent must be level, or have a 1/4 inch rise for every 1 foot of run towards the termination. Never allow the vent to run downward. This could cause high temperatures and may present a possible fi re hazard. Regency ® L676E Direct Vent Gas Fireplace...
-
Page 19: Venting Arrangements
Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor to Set 1, Set 2 or Set 3 if required. A vent guard maybe required as per local codes, refer to "Exterior Vent Termination Requirements" section for details. Note: Regency ®... - Page 20 4' Max. 10' Min. 7' Max. between 90 elbows is 6' Min. 6' Max. 11' Min. 9' Max. required. VENT RESTRICTOR SETTING: Vent restrictor must be at Set 0 for both NG and LP. Regency ® L676E Direct Vent Gas Fireplace...
- Page 21 Please note min. 1 foot 5' Min. 6' Max. 8' Min. between 90 elbows is 6' Min. 8' Max. 9' Min. required. VENT RESTRICTOR SETTING: Vent restrictor must be at Set 0 for both NG and LP. Regency ® L676E Direct Vent Gas Fireplace...
-
Page 22: Venting Arrangements
Refer to "Vent Restrictor Position" section for details on how to change the vent restrictor to Set 1, Set 2 or Set 3 if required. Note: Must use optional fl ue adapter when using Rigid Pipe (Part # 770-994). Regency ® L676E Direct Vent Gas Fireplace... -
Page 23: Unit Installation With Horizontal Termination
Diagram 7 warranty. Silicone (red RTV) is optional. NOTE: A Vent Guard is required when the AstroCap is installed above grade at 7 feet or lower. Diagram 1 Regency ® L676E Direct Vent Gas Fireplace... -
Page 24: Unit Installation With Vertical Termination
Diagram 5 or local codes. Note that for steep roof pitches, Diagram 3 the vertical height must be increased. Regency ® L676E Direct Vent Gas Fireplace... -
Page 25: Horizontal Termination With Flex Vent System
1-3/8"(35mm) and fasten with the 3 screws. NOTE: Horizontal sections must be sup- ported at intervals not exceeding 3 feet (0.9 meter). (Flame picture and performance will be affected by sags in the liner). Regency ® L676E Direct Vent Gas Fireplace... -
Page 26: High Elevation
42,000 Btu/h 11) Main Gas Inlet (12.3 kW) Note: If you have an incorrect fl ame pattern, L676E-LP SYSTEM DATA ® contact your Regency dealer for Min. Supply Pressure 12" WC (2.98 kpa) further instructions. Low Setting Man. 3.6" WC (2.49 kpa) Incorrect fl... -
Page 27: Back-Up Battery Installation
fi rebox). 5) Pull out the black and red battery wires from the right side of the fi rebox. Battery Wires 8) Re-install the heat shield. Regency ® L676E Direct Vent Gas Fireplace... -
Page 28: Brick Panel Installation
Place the door on a soft surface to prevent scratching. 2) Unwrap the brick panels from the protective wrapping. Note: The logs must not be in the unit. Right Side Left Side Back Brick Back Brick Panel Panel Regency ® L676E Direct Vent Gas Fireplace... - Page 29 The top of the brick panel is held in place by a magnet that sits against the bracket as shown in the image below. Top Brick Panel Repeat for left side exterior brick panel. Right Side Brick Panel Bracket Brick Panel Clip Base Brick Panel Slot Regency ® L676E Direct Vent Gas Fireplace...
-
Page 30: Log Set Installation
2) Place log 03-25 on the rear log support pins. Backside of Grate 5) Line up the two holes on the underside of log 03-26 with the pins on logs 03-25 and 03-27 and fi t in place. 03-26 03-25 03-25 03-27 Regency ® L676E Direct Vent Gas Fireplace... - Page 31 Embers in between front burner tube and grate. 7) Spread the vermiculite on the base brick panel covering the remaining exposed base brick. Embers on bottom brick panel. Complete Log Set Installation 03-25 03-26 03-28 03-27 Regency ® L676E Direct Vent Gas Fireplace...
-
Page 32: Wiring Diagram
Wiring errors can rear burners will operate on low, when the unit cause improper and dangerous is running on battery back-up. operation. (Do not cut the ground terminal off under any circumstances.) Regency ® L676E Direct Vent Gas Fireplace... -
Page 33: Operating Instructions
fi rebox). 3) Check to ensure there are no gas leaks. 4) Make sure the glass in the door frame is properly positioned. Never operate the appliance with the glass removed. Regency ® L676E Direct Vent Gas Fireplace... -
Page 34: Lighting Procedure
Do not dispose of batteries in a fi re. The batteries may explode. Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic. Regency ® L676E Direct Vent Gas Fireplace... -
Page 35: Copy Of Lighting Plate Instructions
Press the ON/OFF button once on the Remote Control. If service is to be performed, you must disconnect both sources of power to the unit; main power and the battery. DO NOT REMOVE THIS INSTRUCTION PLATE 918-628 Regency ® L676E Direct Vent Gas Fireplace... -
Page 36: Maintenance Instructions
Regency ® uses StoveBright * Replacement of the glass panel(s) should be out the joints, Continuous condensation can Paint - Metallic Black #6309. -
Page 37: Back-Up Battery Replacement
3) Loosen the 2 screws that hold the right side heat shield in place. Heat Shield 5) Replace with new battery and reconnect battery wires accordingly. 6) Re-install the battery to the right side of the fi rebox. 7) Re-install the right side heat shield. Regency ® L676E Direct Vent Gas Fireplace... - Page 38 10) Replace the control box. 11) Re-connect wires harnesses. Ensure that the cables match the letters labelled on the control box and are securely connected. 12) Reinstall the ground screw. 13) Reverse steps 8 to 1. Regency ® L676E Direct Vent Gas Fireplace...
-
Page 39: Valve Tray Replacement
4) Remove the interior brick panels. 5) Remove the grate by undoing the 2 screws on the left and right Back Burner side. 8) Remove the rear log stand by removing the 4 screws. Rear Log Stand Grate Regency ® L676E Direct Vent Gas Fireplace... - Page 40 fi rebox. NOTE: The control box will need to be fl ipped as it is being brought out from the side of the fi rebox. Back-up Battery shown Regency ® L676E Direct Vent Gas Fireplace...
- Page 41 17) Remove the 16 screws that hold the valve tray to the fi rebox and 29) Check for proper fl ame appearance. carefully pull out the valve tray. 30) Re-install the exterior brick panels. Valve Tray 18) Disconnect the black and red wires from the solenoid valve. Regency ® L676E Direct Vent Gas Fireplace...
-
Page 42: Parts List
Birch Log Set 521-935 Oak Log Set 946-556 Heat Wave Kit 946-570 Heat Release Kit 521-969E LP Conversion Kit 918-621 Manual 910-960 FireWizard Remote Control 918-619 Manual FireWizard-E * Not available as a replacement part. Regency ® L676E Direct Vent Gas Fireplace... -
Page 43: Burner & Log Assembly
Pilot Assembly - NG 910-953 Pilot Assembly - LP 904-617 NG - Orifi ce #34 904-622 NG - Orifi ce #48 904-241 LP - Orifi ce #56 904-345 LP - Orifi ce #53 910-937 Valve Solenoid Regency ® L676E Direct Vent Gas Fireplace... - Page 44 NOTES ® Regency L676E Direct Vent Gas Fireplace...
- Page 45 NOTES ® Regency L676E Direct Vent Gas Fireplace...
- Page 46 NOTES ® Regency L676E Direct Vent Gas Fireplace...
-
Page 47: Warranty
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency ®... - Page 48 Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency, Liberty, AstroCap, HeatWave, Heat Release and FireWizard are trademarks of FPI Fireplace Products International Ltd. © Copyright 2008, FPI Fireplace Products International Ltd. All rights reserved. Printed in Canada Regency ®...