1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Snowmobiles
  5. VX500SXBC
  6. Service manual

Yamaha VX500SXBC Service Manual

Hide thumbs Also See for VX500SXBC:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
SUPPLEMENTARY SERVICE MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Yamaha VX500SXBC

Summary of Contents for Yamaha VX500SXBC

  • Page 1 SUPPLEMENTARY SERVICE MANUAL...
  • Page 2 OE001 son inspecting or repairing the snowmobile. NOTICE CAUTION: This manual was written by the Yamaha Mo- tor Company primarily for use by Yamaha A CAUTION indicates special precautions dealers and their qualified mechanics. It is that must be taken to avoid damage to the not possible to put an entire mechanic’s...
  • Page 3 OE031 ILLUSTRATED SYMBOLS (Refer to the illustration) Illustrated symbols 1 to 9 are designed as thumb tabs to indicate the chapter’s number and content. 1 General information 2 Periodic inspection and adjustment 3 Chassis 4 Power train 5 Engine overhaul 6 Cooling system 7 Carburetion 8 Electrical...

  • Page 4: Table Of Contents

    CONTENTS GENERAL INFORMATION ....ENGINE ......MACHINE IDENTIFICATION .

  • Page 5: General Information

    MACHINE IDENTIFICATION/IMPORTANT INFORMATION INFO 1E001 GENERAL INFORMATION MACHINE IDENTIFICATION FRAME SERIAL NUMBER The frame serial number 1 is located on the right-hand side of the frame (just below the front of the seat). ENGINE SERIAL NUMBER The engine serial number 1 is located on the right-hand side of the crankcase.

  • Page 6: Power Train

    Adjust the V-belt position by removing or adding a spacer 2 on each adjusting bolt. For this adjustment, consult a Yamaha deal- er or another qualified mechanic. CAUTION: As the V-belt wears, adjustment may be necessary.
  • Page 7 INSP DRIVE V-BELT 2. Adjust the position of the V-belt by re- moving or adding a spacer 1 on each adjusting bolt 2 . V-belt height adjustment To move V-belt up: Add spacer To move V-belt down: Reduce spacer 3. Tighten: S Adjusting bolt Adjusting bolt: 10 Nm (1.0 mSkg, 7.2 ftSlb)

  • Page 8: Brake Pad Inspection

    INSP BRAKE PAD INSPECTION/SLID RUNNER INSPECTION BRAKE PAD INSPECTION 1. Apply the brake lever. 2. Inspect: S Brake pad Wear indicator 1 nearly contacts the brake disc ! Replace the brake pads as a set. Wear limit a : 4.7 mm (0.185 in) SLIDE RUNNER INSPECTION 1.

  • Page 9: Tuning

    INSP CLUTCH TUNING W White S Silver Blue CLUTCH P Pink R Red O Orange High altitude Y Yellow G Green Specifications Model: VX500SXB 4,500 X 7,000 ft X 3,500 ft 3,000 X 5,000 ft 6,500 X 10,000 ft Elevation Idle speed Approx.
  • Page 10 INSP CLUTCH W white S Silver Blue P Pink R Red O Orange Y Yellow G Green Specifications Model: VX700ER X 3,500 ft 3,000 X 5,000 ft 4,500 X 7,000 ft 6,500 X 10,000 ft Elevation Idle speed Approx. 1,600 r / min Clutch Approx.
  • Page 11 INSP CLUTCH 2E331 The clutch may require tuning depending upon the area of operation and desired han- dling characteristics. The clutch can be tuned by changing engagement and shifting speed. Clutch engagement speed is defined as the engine speed where the machine first begins to move from a complete stop.

  • Page 12: Gear Selection

    INSP GEAR SELECTION GEAR SELECTION The reduction ratio of the driven gear to the drive gear must be set according to the snow conditions. If there are many rough surfaces unfavorable snow conditions, drive/driven gear ratio should be increased. If the surfaces are fairly smooth or better snow conditions exist, decrease the ratio.
  • Page 13 INSP GEAR SELECTION 3 Secondary spring Spring rate Wire Free No. of Parts No. NSmm/ rad Color gauge length Standard coils (kgmm/ rad) (mm) (mm) 90508-500B1 6003 (613) BROWN 90508-536A9 7147 (729) VX500 90508-556A2 8314 (848) GREEN VX700 90508-556A7 9460 (965) SILVER 4 Secondary spring twist angle Seat...
  • Page 14 INSP GEAR SELECTION 6 Primary spring Spring rate Wire Outside Free Preload No. of Standard Parts No. N / mm Color gauge diameter length (kg) coils (kg / mm) (mm) (mm) (mm) 90501-481J1 9.8 (1.0) 196.1 (20) S-B-S 5.16 85.4 90501-487G8 14.7 (1.5) 147 (15)

  • Page 15: Front Suspension

    INSP FRONT SUSPENSION FRONT SUSPENSION Spring preload (700) 1. Adjust: S Turn the adjusting ring 1 to the proper position. Spring adjuster position Softer z ! Harder Preload Standard CAUTION: Be sure that the left and right spring preload is the same. Spring preload (500) 1.

  • Page 16: Rear Suspension

    INSP REAR SUSPENSION REAR SUSPENSION Stopper band 1. Adjust: S Stopper band tension CAUTION: Be sure that the left and right length is the same. NOTE: This adjustment affects the handling charac- teristics of the machine. Adjustment steps: S Loosen the locknut 1 . S Turn the adjusting nut 2 in or out to adjust the stopper band tension.
  • Page 17 INSP REAR SUSPENSION Spring preload (500) 1. Adjust: S Turn the spring seat 1 in or out. Spring seat Standard Shorter z ! Longer distance Harder z ! Softer Preload Length Max. Min. (front) 172 mm 182 mm 192 mm (6.77 in) (7.17 in) (7.56 in) Length Max.

  • Page 18: Chassis

    CHAS CHASSIS SKI (500) 10 Nm (1.0 mSkg, 7.2 ftSlb) 21 Nm (2.1 mSkg, 15 ftSlb) 48 Nm (4.8 mSkg, 35 ftSlb) : ESSO beacon 325 grease or Aeroshell grease #7A Order Job name/Part name Q’ty Remarks Ski removal Remove the parts in the order below. Cotter pin Ski column lower bracket Ski stopper...

  • Page 19: Inspection

    CHAS SKI/FRONT SUSPENSION INSPECTION 1. Inspect: S Ski 1 S Ski runner 2 S Ski column lower bracket 3 S Ski handle 4 S Ski stopper 5 Wear/cracks/damage ! Replace. S Mounting bolt 6 S Collar 7 Wear/damage ! Replace. FRONT SUSPENSION This shock absorber contains highly com- pressed nitrogen gas.

  • Page 20: Installation

    CHAS FRONT SUSPENSION INSTALLATION 1. Install: S Control rod 1 S Nut 2 S Joint 3 a Set length Left hand Model Set length (mm) angle (_) 460.2 ± 0.5 mm VX500 94 ± 1 (18.11 ± 0.0197 in) Upper 458.7 ±...

  • Page 21: Power Train

    POWR SECONDARY SHEAVE ASSEMBLY 1. Install: S Secondary sheave spring 1 S Bolts 2 (along with the shims) Bolt: 10 Nm (1.0 mSkg, 7.2 ftSlb) 2. Install: S Stopper S Sliding sheave Screw (stopper): 6.5 Nm (0.65 mSkg, 4.6 ftSlb) 3.

  • Page 22: Drive Chain Housing

    POWR DRIVE CHAIN HOUSING DRIVE CHAIN HOUSING WITHOUT REVERSE MODEL (500) 10 Nm (1.0 mSkg, 7.2 ftSlb) 24 Nm (2.4 mSkg, 17 ftSlb) 48 Nm (4.8 mSkg, 35 ftSlb) 60 Nm (6.0 mSkg, 43 ftSlb) Order Job name/Part name Q’ty Remarks Drive chain housing removal Remove the parts in the order below.

  • Page 23: Installation

    POWR DRIVE CHAIN HOUSING INSTALLATION During installation, pay attention to the fol- lowing point: A Make sure that the bearing seals face towards the drive chain, as shown. B Properly install the rubber seal onto the drive chain housing, making sure that these are no gaps.

  • Page 24: Drive Chain Housing And Jackshaft Installation

    POWR DRIVE CHAIN HOUSING DRIVE CHAIN HOUSING AND JACKSHAFT INSTALLATION 1. Install: S Drive chain housing S Jackshaft Installation steps: D Install the drive chain housing 1 . D Tighten the bolts 2 . Bolt (drive chain housing): 48 Nm (4.8 mSkg, 35 ftSlb) D Temporarily tighten the nuts 3 .

  • Page 25: With Reverse Model (700)

    POWR DRIVE CHAIN HOUSING WITH REVERSE MODEL (700) 10 Nm (1.0 mSkg, 7.2 ftSlb) 24 Nm (2.4 mSkg, 17 ftSlb) 48 Nm (4.8 mSkg, 35 ftSlb) 60 Nm (6.0 mSkg, 43 ftSlb) Order Job name/Part name Q’ty Remarks Drive chain housing removal Remove the parts in the order below.
  • Page 26 POWR DRIVE CHAIN HOUSING Order Job name/Part name Q’ty Remarks Reverse drive gear Spring Chain tensioner Roller Collar Spring Journal Reverse driven gear Washer Forward driven sprocket Collar Counter gear Drive sprocket Drive chain Collar Washer Plate Shaft Drive chain housing For installation, reverse the removal procedure.

  • Page 27: Installation

    POWR DRIVE CHAIN HOUSING/JACKSHAFT INSTALLATION During installation, pay attention to the fol- lowing point: A Properly install the rubber seal onto the drive chain housing, making sure that these are no gaps. B Make sure that the bearing seals face towards the drive chain, as shown.

  • Page 28: Brake

    POWR BRAKE BRAKE 1.5 Nm (0.15 mSkg, 1.1 ftSlb) 6 Nm (0.6 mSkg, 4.3 ftSlb) Order Job name/Part name Q’ty Remarks Brake caliper disassembly Disassembly the parts in the order below. Cap bolt Retaining pin Pad spring Brake pads Shim 1 Shim 2 Bleed screws Oil seals...

  • Page 29: Brake Pad Replacement

    POWR BRAKE CAUTION: Disc brake components rarely require disas- sembly. DO NOT: D Disassemble components unless abso- lutely necessary. D Use solvents on internal brake compo- nents. D Use contaminated brake fluid for clean- ing. Use only clean brake fluid. D Allow brake fluid to come in contact with the eyes, otherwise eye injury may occur.
  • Page 30 POWR BRAKE 2. Install: S Brake pads S Pad spring Installation steps: S Connect a suitable hose 1 tightly to the caliper bleed screw 2 . Put the other end of this hose into an open container. S Loosen the caliper bleed screw and push the pistons into the caliper with the finger.

  • Page 31: Slide Rail Suspension

    POWR SLIDE RAIL SUSPENSION SLIDE RAIL SUSPENSION 71 Nm (7.1 mSkg, 51 ftSlb) Order Job name/Part name Q’ty Remarks Slide rail suspension removal Remove the parts in the order below. Tension adjuster Loosen. Blind caps Bolts Washer Slide rail suspension For installation, reverse the removal procedure.
  • Page 32 POWR SLIDE RAIL SUSPENSION 4 Nm (0.4 mSkg, 2.9 ftSlb) 15 Nm (1.5 mSkg, 11 ftSlb) 30 Nm (3.0 mSkg, 22 ftSlb) 49 Nm (4.9 mSkg, 35 ftSlb) 71 Nm (7.1 mSkg, 50 ftSlb) 24 Nm (2.4 mSkg, 17 ftSlb) Order Job name/Part name Q’ty...
  • Page 33 POWR SLIDE RAIL SUSPENSION 24 Nm (2.4 mSkg, 17 ftSlb) 49 Nm (4.9 mSkg, 35 ftSlb) 71 Nm (7.1 mSkg, 50 ftSlb) Order Job name/Part name Q’ty Remarks Suspension wheels Collar Wheel brackets Circlips Suspension wheels Bushings Shaft Rear suspension bracket Spacers Bushings Collar...
  • Page 34 POWR SLIDE RAIL SUSPENSION 49 Nm (4.9 mSkg, 35 ftSlb) 71 Nm (7.1 mSkg, 50 ftSlb) Order Job name/Part name Q’ty Remarks Rear shock absorber Bushings Collar Pull rod Collars Bushings Collars (700) Suspension wheels Control rods Bushings Screw Bushings –30–...
  • Page 35 POWR SLIDE RAIL SUSPENSION 24 Nm (2.4 mSkg, 17 ftSlb) 71 Nm (7.1 mSkg, 50 ftSlb) 75 Nm (7.5 mSkg, 54 ftSlb) Order Job name/Part name Q’ty Remarks Rear pivot arm Bushings Collar Collar Rear pivot arm bracket Collar Circlips Suspension wheels Wheel bracket Rear axle...

  • Page 36: Front Axle And Track

    POWR FRONT AXLE AND TRACK FRONT AXLE AND TRACK 27 mm INSTALLATION (1.06 in) Reverse the “REMOVAL” procedure. Note the following points. 1. Install: S Sprocket wheels S Guide wheels 60 mm 132.6 mm 201.4 mm (2.36 in) (5.22 in) (7.93 in) NOTE: 164.1 mm...

  • Page 37: Engine

    ENGINE ASSEMBLY ENGINE ENGINE ASSEMBLY 90 Nm (9.0 mSkg, 65 ftSlb) 60 Nm (6.0 mSkg, 43 ftSlb) Order Job name/Part name Q’ty Remarks Engine removal Remove the parts in the order below. Exhaust pipe Carburetor Refer to “CARBURETOR”. Recoil starter Refer to “RECOIL STARTER”.
  • Page 38 ENGINE ASSEMBLY 23 Nm (2.3 mSkg, 17 ftSlb) 60 Nm (6.0 mSkg, 43 ftSlb) 90 Nm (9.0 mSkg, 65 ftSlb) 23 Nm (2.3 mSkg, 17 ftSlb) Order Job name/Part name Q’ty Remarks Engine removal Remove the parts in the order below. Exhaust pipe Carburetor Refer to “CARBURETOR”.

  • Page 39: Cylinder Head And Cylinder

    CYLINDER HEAD AND CYLINDER CYLINDER HEAD AND CYLINDER INSPECTION 1. Measure: S Piston-to-cylinder clearance Measurement steps: 1st step: S Measure the cylinder bore “C” with a cylinder bore gauge 1 . NOTE: Measure the cylinder bore “C” parallel to, and at right angles to the crankshaft. Then find the average of the measurements.
  • Page 40 CYLINDER HEAD AND CYLINDER 2nd step: S Measure the piston skirt diameter “P” with a micrometer from distance a . a 500: 25 mm (0.98 in) 700: 15 mm (0.59 in) from the piston bottom edge. Piston size P 500: 67.930 X 67.935 mm (2.6745 X 2.6746 in) Standard 700: 70.425 X 70.430 mm...

  • Page 41: Heat Exchanger

    COOL HEAT EXCHANGER COOLING SYSTEM HEAT EXCHANGER 1. Measure: S Filler cap opening pressure Cap opens at pressure below the speci- fied pressure ! Replace. Cap opening pressure: 95 X 125 kPa (0.95 X 1.25 kg/cm 13.58 X 17.87 psi) Measurement steps: D Attach the cooling system tester (90890-01325, YU-24460-01) to the...

  • Page 42: Carburetion

    CARB CARBURETORS CARBURETION CARBURETORS * Intake silencer D First, remove the throttle cable from the cable guide on the steering column. D Adjust the throttle cable free play while the cable is in the cable guide. D After adjusting the throttle cable free play, properly install the upper and lower intake silencer plates and seal.
  • Page 43 CARB CARBURETORS * Intake silencer D First, remove the throttle cable from the cable guide on the steering column. D Adjust the throttle cable free play while the cable is in the cable guide. D After adjusting the throttle cable free play, properly install the upper and lower intake silencer plates and seal.
  • Page 44 CARB CARBURETORS Order Job name/Part name Q’ty Remarks Carburetor separation Separation the parts in the order below. Coolant hoses Starter cable holder Collar Spring Screw Loosen Starter rod Spring Starter levers Breather hoses Top covers Gaskets Throttle shaft connecting screws Connecting plate (upper) Connecting plate (lower) For assembly, reverse the separation...

  • Page 45: Assembly

    CARB CARBURETORS ASSEMBLY 1. Measure: S Float height a Out of specification ! Adjust. Float height: 22.3 ± 2.0 mm (0.878 ± 0.080 in) 13.3 ± 2.0 mm (0.524 ± 0.080 in) Measurement and adjustment steps: S Hold the carburetor in an upside down position.

  • Page 46: Specifications

    Maximum torque r/min Starting system Recoil hand starter Electric and recoil hand starter Lubrication system: Separate lubrication (YAMAHA AUTOLUBE) Engine oil: Type YAMALUBE 2-cycle oil Tank capacity 3.0 L (2.6 Imp gt, 3.2 Us gt) Drive chain housing oil: Type Gear oil API “GL-3”...
  • Page 47 SPEC GENERAL SPECIFICATIONS Model VX500SXB VX700ER Carburetor: Type/quantity TM36 TM33 Manufacturer MIKUNI Spark plug: Type BR9ES Manufacturer 0.7 X 0.8 mm (0.028 X 0.031 in) Transmission: Primary reduction system V-Belt 3.8 X 1.0 : 1 Primary reduction ratio Clutch type Automatic centrifugal engagement Secondary reduction system...

  • Page 48: Maintenance Specifications

    SPEC MAINTENANCE SPECIFICATIONS MAINTENANCE SPECIFICATIONS ENGINE Model VX500SXB VX700ER Cylinder head: 23.3 X 23.9 cm 22.9 X 23.5 cm Volume (with spark plug) <Warp limit> <0.03 mm (0.0012 in)> * Lines indicate straight edge measurement. Cylinder: Material Aluminum alloy with dispersion coating 68.00 X 68.02 mm 70.50 X 70.52 mm...
  • Page 49 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Crankshaft: 61.95 X 62.00 mm 55.95 X 56.00 mm Crank width “A” (2.439 X 2.440 in) (2.203 X 2.205 in) 179.85 X 180.15 mm 291.75 X 292.30 mm Crank width “B” (7.080 X 7.093 in) (11.486 X 11.508 in) Crankshaft deflection “C”...
  • Page 50 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Carburetor: Type/Quantity TM36/2 pcs. TM33/3 pcs. Manufacturer MIKUNI I.D. mark 8CJ10 8CH10 Main jet (M.J) #151.3 #1 : #145 #2, 3 : #143.8 Main air jet (M.A.J) ø2.5 – Pilot jet (P.J) Jet needle (J.N) 8CFY14-56-2 6DGM5-3 Needle jet (N.J)
  • Page 51 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Thermostat: 50 X 55_C Opening temperature (122_F X 132_F) Valve lift 8 mm/70_C (159_F) –47–...

  • Page 52: Power Train

    SPEC MAINTENANCE SPECIFICATIONS POWER TRAIN Model VX500SXB VX700ER Transmission: Type V-belt automatic 3.8 X 1.0 : 1 Range of ratio 4,000 ± 200 r/min Engagement r/min 7,800 ± 250 r/min 8,300 ± 250 r/min Shift r/min 267 X 270 mm Sheave center distance “A”...
  • Page 53 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Rivet: Outer Part number 90261-06034 90261-06015 Material Steel Size 13.9 mm (0.55 in) 10.3 mm (0.40 in) Quantity 3 pcs Hole quantity 3 pcs Inner Part number 90261-06028 90261-06034 Material Aluminum Steel Size 10.3mm (0.40in) 13.9 mm (0.55 in) Quantity 3 pcs...
  • Page 54 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Track: Part number 8AB-47110-10 8CH-47110-00 Width 381 mm (15.0 in) Length 3,072 mm (120.9 in) Pitch 64 mm (2.52 in) Number of links Height “B” 16 mm (0.63 in) 25 X 30 mm Deflection at 10 kg (22 lb) (0.98 X 1.18 in) Slide rail suspension: Front travel...
  • Page 55 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Shock absorber: Damping force Front 3,320N ± 460N/0.3m/s 720 N ± 150N/0.3m/s Extension 1,110N ± 225N/0.3m/s 1,020 N ± 210N/0.3m/s Compression Rear 1,950N ± 264N/0.3m/s 2,206 N ± 657N/0.3m/s Extension 1,380N ± 235N/0.3m/s 726 N ± 216N/0.3m/s Compression Slide runner: Thickness...

  • Page 56: Chassis

    SPEC MAINTENANCE SPECIFICATIONS CHASSIS Model VX500SXB VX700ER Frame: Frame material Aluminum Seat height 685 mm (26.8 in) 730 mm (28.7 in) Luggage box location Rear side of seat Steering: Lock-to-lock angle (left) 29.6_ (R ski) 34.8_ (L ski) 29.4_ (R ski) 34.7_ (L ski) (right) 34.8_ (R ski) 29.6_ (L ski) 34.7_ (R ski) 29.4_ (L ski)

  • Page 57: Electrical

    18_ at 4.500 r/min 24_ at 4.500 r/min Advanced type Electrical type Ignition coil: Model/Manufacturer 8AB-00/YAMAHA 8DG-00/YAMAHA Minimum spark gap 3 mm (0.118 in) or more 0.2 Ω ± 20% at 20_C (68_F) 0.06 Ω ± 20% at 20_C Primary coil resistance (68_F) 4.9 kΩ...
  • Page 58 SPEC MAINTENANCE SPECIFICATIONS Model VX500SXB VX700ER Rectifier/regulator: Model/manufacturer 8CR-00/MATSUSHITA 13.8 X 14.8 V No load regulated voltage 14.0 X 15.0 V Battery: (for electric model) Specific gravity – 1.280 Type – GM18Z-3A Electric starter system: (for electric model) Type – Bendix Starter motor: (for electric model) Model/manufacturer...
  • Page 59 SPEC MAINTENANCE SPECIFICATIONS High altitude settings VX500SXB Tempera- – 40_C – 29_C – 18_C – 7_C 15_C ture (– 40_F) (– 20_F) (0_F) (20_F) (40_F) (60_F) Altitude 0 X 100 m MJ#155 MJ#153.8 MJ#152.5 MJ#151.3 MJ#150 (0 X 330 ft) JN-2.0 JN-2.0 JN-2.0...
  • Page 60 SPEC MAINTENANCE SPECIFICATIONS High altitude settings VX700ER Tempera- – 40_C – 29_C – 18_C – 7_C 15_C ture (– 40_F) (– 20_F) (0_F) (20_F) (40_F) (60_F) Altitude MJ#1 #148.8 MJ#1 #147.5 MJ#1 #146.3 MJ#1 #145.0 MJ#1 #143.8 MJ#2#3 #147.5 MJ#2#3 #146.3 MJ#2#3 #145.0 MJ#2#3 #143.8 MJ#2#3 #142.5...
  • Page 61 SPEC MAINTENANCE SPECIFICATIONS Tightening torque: Tightening torque Parts to be tightened Parts to be tightened Remarks Remarks mSkg ftSlb Crankcase (first) Tighten the bolts in two Crankcase (final) stages. Engine bracket (front) and frame 500 Engine bracket (front) and frame Engine bracket damper (front) Engine bracket and engine Engine bracket upper and lower (rear)
  • Page 62 SPEC MAINTENANCE SPECIFICATIONS Tightening torque Parts to be tightened Parts to be tightened Remarks Remarks mSkg ftSlb Sliding frame and slide runner Slide rail suspension mounting bolt  Rear pivot arm and bracket Apply LOCTITE Shock absorber and rear pivot arm Rear pivot arm and rod Rear suspension bracket and rod Control rod and sliding frame...
  • Page 63 SPEC MAINTENANCE SPECIFICATIONS –59–...

  • Page 64: Cable Routing <500

    SPEC CABLE ROUTING CABLE ROUTING <500> –60–...
  • Page 65 SPEC CABLE ROUTING CABLE ROUTING <For 500> 1 Oil pump cable 2 Throttle cable 3 Fasten the wire harness. Do not fasten the throttle cable and oil pump cable. 4 Fasten the throttle cable and oil pump cable with a plastic clamp. Route the cable along the side of the handle holder.
  • Page 66 SPEC CABLE ROUTING –62–...
  • Page 67 SPEC CABLE ROUTING 35 To the conduction 36 Voltage regulator 37 Rectifire regulator 38 Fasten the wire harness with a plastic clamp. 39 Rectifire regulator (ECC model) 40 Brake hose holder 41 Fasten the wire harness with a plastic clamp. 42 To reverse gear 43 Fasten the wire harness, fuel breather hose and oil...
  • Page 68 SPEC CABLE ROUTING –64–...
  • Page 69 SPEC CABLE ROUTING 1 Wire lead (electrical starter model) 2 Carburetor switch coupler 3 Fasten the throttle cable and oil pump cable with a plastic clamp. 4 Air temperature sensor coupler (ECC model) 5 Coolant hose 6 Starter relay lead 7 Starter relay sub lead (electrical starter model) 8 Fasten the wire harness,...
  • Page 70 SPEC CABLE ROUTING –66–...
  • Page 71 SPEC CABLE ROUTING 32 Solenoid coupler (ECC model) 33 Ignition coil 34 Carburetor heating lever 35 Coolant hose 36 Speedometer cable 37 Fasten the throttle cable, water temperature sensor lead, carburetor switch lead and solenoid lead with a plastic clamp. 38 Water temperature sensor coupler 39 Under 50 mm (1.97 in)
  • Page 72 SPEC CABLE ROUTING –68–...
  • Page 73 SPEC CABLE ROUTING 1 Make sure that the oil tank cap and oil breather hose do not touch each other. 2 Route the fuel breather hose along the upper of the main harness. 3 Route the oil breather hose along the upper of the main harness.

  • Page 74: Cable Routing <700

    SPEC CABLE ROUTING CABLE ROUTING <700> –70–...
  • Page 75 SPEC CABLE ROUTING CABLE ROUTING <For 700> 1 Oil pump cable 2 Throttle cable 3 Do not fasten the throttle cable and oil pump wire with a plastic clamp. 4 Thumb warmer coupler 5 Engine stop switch coupler 6 Holder 7 Grip warmer coupler 8 Brake light switch coupler 9 Head light switch coupler...
  • Page 76 SPEC CABLE ROUTING –72–...
  • Page 77 SPEC CABLE ROUTING 37 DC back buzzer (reverse model) 38 Voltage regulator 39 Rectifier regulator 40 DC back buzzer coupler 41 Fasten the wire harness with a plastic clamp. 42 Brake hose holder 43 Fasten the wire harness with a plastic clamp. 44 To reverse gear 45 Fasten the wire harness, fuel breather hose and oil...
  • Page 78 SPEC CABLE ROUTING –74–...
  • Page 79 SPEC CABLE ROUTING 1 Fasten the carburetor switch, water temperature sensor lead, coolant hose, wire lead and battery negative lead with a plastic clamp. 2 Clamp 3 Fasten the ignition coil and starter cable with a plastic clamp. 4 Fasten the wire lead, battery negative lead and coolant hose with a plastic clamp.
  • Page 80 SPEC CABLE ROUTING –76–...
  • Page 81 SPEC CABLE ROUTING 1 Wire harness 2 50 mm (1.97 in) 3 Make sure that the oil tank cap and oil breather hose do not touch each other. 4 Route the fuel breather hose along the upper of the main harness.
  • Page 82 WIRING DIAGRAM VX500SXB CDI magneto Brake light switch Rectifier / regulator Tail / brake light Starter relay / fuse Speedometer assembly Battery Oil level indicator light Starter motor Water temp. indicator light Main switch High beam indicator light Engine stop switch Speedometer light Throttle switch Tachometer assembly...
  • Page 83 WIRING DIAGRAM VX700ER CDI magneto Brake light switch Rectifier / regulator Tail / brake light Starter relay / fuse Speedometer assembly Battery Oil level indicator light Starter motor Water temp indicator light Main switch High beam indicator light Engine stop switch Speedometer light Throttle switch Tachometer assembly...
  • Page 84 PRINTED IN USA PRINTED ON RECYCLED PAPER...

This manual is also suitable for:

Vx700erc

Table of Contents