Sony DSR-45 Service Manual page 29

DSR-45/45P
DISPLAY SET menu
Submenu
Icon/Menu Setting
(page)
DISPLAY DATA CODE Selects whether or not to display the data codes on the LCD monitor and the MONITOR
DISP
SET (page 36 (GB))
VIDEO output.
OFF : Does not display the data codes.
DATE: Displays the date when recorded.
CAMERA: Displays the camera data.
EE/PB SEL Sets the stop, fast-forward and rewind modes.
(page 17 (GB)) EE : Outputs EE pictures (sound, time code).
PB: Mutes the image and sound.
Notes
• Even if EXT SYNC on the VIDEO SET menu is set to ON, the line-outs (VIDEO OUT,
COMPONENT OUT, S VIDEO OUT) in the EE mode are delayed from those of the input
signals as follows:
– delayed for two lines when signals are input via the VIDEO IN REF.IN connector.
– delayed for one line when signals are input via the S VIDEO IN or COMPONENT IN
connector.
• If this item is set to PB, the output from the unit will be as follows when you press any of
the REC, DUP, or AUDIO DUB buttons separately when the unit is stopped (unless the
cassette has been write-protected).
REC button EE picture of
the input image
DUP button Image input to
the DV jack
AUDIO Mute screen
DUB button (black)
Mute screen
No button
(black)
is pressed
LTR SIZE Changes the font size of the menu line at the cursor.
NORMAL : Normal size
2×: Double height size
COLOR BAR Displays/hides the color bars.
(for DSR-45) / OFF : Does not display the color bars.
COLOUR BAR
ON: Displays the color bars.
(for DSR-45P)
Notes
• You cannot display the color bars while the unit is playing the tape or when the INPUT
SELECT selector is set to DV.
• The color bars are displayed only on the LCD monitor or MONITOR VIDEO output.
• If you record when the color bars are displayed, the color bars will also be recorded on the
tape.
• You cannot adjust the MONITOR VIDEO output. Do not use the color bars output from the
MONITOR VIDEO jack as a reference signal.
• The reference sound signals are not output even if this item is set to ON.
• This item will be automatically set to OFF if you set the INPUT SELECT selector to DV or
you operate the unit to play back a tape.
Submenu
Icon/Menu Setting
(page)
VIDEO SET PB LEVEL Adjusts the output video signal levels. (This is available only when the mode is playback,
V
(page 68 (GB)) playback pause, slow playback, cue, or review.)
SETUP: Switches the luminance signal setup level (0% or 7.5%). (This item is only for the
DSR-45. The setup level for the DSR-45P is fixed to 0%.)
Y LEVEL: Adjusts the Y signal level of the component signals. (If you change this, the Y
signal level of the composite video and S VIDEO will also be changed.)
R-Y LEVEL: Adjusts the R-Y signal level of the component signals. (If you change this,
the chrominance level of the composite video and S VIDEO will also be changed.)
B-Y LEVEL: Adjusts the B-Y signal level of the component signals. (If you change this,
the chrominance level of the composite video and S VIDEO will also be changed.)
CHROMA: Adjusts the chrominance level in the composite signals.
Notes
• You can adjust the video levels only while playing the tape.
• Adjust the video levels by looking at the bars (except SETUP). (The triangles under the
bars are displayed in green when the settings are set to the factory preset values.)
• The SETUP default is 0%. Other defaults are their center values.
• The output video signals can be adjusted only for VIDEO OUT, COMPONENT OUT, or S
VIDEO OUT.
• Set SETUP to 7.5% only if the tape has been recorded at 0% and you want to play back
the tape at 7.5%. If you play back a 7.5% tape at the 7.5% setting, the tape will not be
played at the proper brightness. If you set SETUP at 0% and if you play back a 7.5% tape,
the tape will be played at 7.5%. (You cannot play the tape at 0%.)
EXT SYNC Switches the externally synchronized playback setting.
OFF : No external synchronization
ON: External synchronization
Notes
• It may take three or more seconds until a stable image is output in the externally-
synchronized playback mode.
• In the externally-synchronized playback mode, jitter may appear on the MONITOR VIDEO
output or on the LCD monitor image. Use the VIDEO OUT connector to output an
externally-synchronized image. Set this item to OFF when you use the MONITOR VIDEO
output.
H PHASE Roughly adjusts the sync phase in the externally-synchronized playback mode.
(page 66 (GB)) Press the J/j buttons to move the bar and press the EXEC button to select. (The triangle
under the bar is displayed in green when the setting is set to the factory preset value.)
Notes
• You can adjust this item only in the externally-synchronized playback mode.
• If you change this item, the H PHASE F value will be set to the factory preset value.
H PHASE F Finely adjusts the sync phase in the externally-synchronized playback mode.
(page 66 (GB)) Press the J/j buttons to move the bar and press the EXEC button to select. (The triangle
under the bar is displayed in green when the setting is set to the factory preset value.)
Notes
• You can adjust this item only in the externally-synchronized playback mode.
• If you change the H PHASE value, this item is set to the factory preset value.
Image Sound Time code
EE sound of the
input sound
Sound input to
the DV jack
(See page 63 (GB))
EE sound of the
input sound
Mute
(no sound)
Chapter 6 Adjusting and Setting Through Menus
(Continued)
Chapter 6 Adjusting and Setting Through Menus
Operating the Menus
Submenu
Icon/Menu
(page)
DISPLAY DATE DISP
DISP
SET
TIME DISP
VIDEO SET menu
Note
To perform the adjustment in H PHASE, H PHASE F,
SC PHASE, or SC PHASE F, you must set EXT
SYNC to ON and input the reference video signals to
the VIDEO IN REF.IN connector.
Submenu
Icon/Menu
(page)
VIDEO SET PB YNR
V
PB CNR
85 86
(GB) (GB) Chapter 6 Adjusting and Setting Through Menus
Operating the Menus
Submenu
Icon/Menu
(page)
VIDEO SET SC PHASE
V
(page 66 (GB))
SC PHASE F
(page 66 (GB))
AUDIO SET menu
Submenu
Icon/Menu
(page)
AUDIO SET AUDIO
A
MODE
(page 74 (GB))
AUDIO DUB
(page 74 (GB))
JOG AUDIO
87 88
(GB) (GB) Chapter 6 Adjusting and Setting Through Menus
1-20
Setting
Selects the form of the date displayed on the search screen or of the data codes and so on.
Y/M/D: Displays YY/MM/DD (year/month/day).
M/D/Y: Displays MM/DD/YY (month/day/year).
D/M/Y: Displays DD/MM/YY (day/month/year).
Note
The default is M/D/Y for the DSR-45; and D/M/Y for the DSR-45P.
Selects the form of the time displayed on the search screen or of the data codes and so on.
24H : Displays 24-hour time.
12H: Displays 12-hour time.
Note
The counter of this unit operates only on a 12-hour cycle. Even if you set this item to 24H,
the counter value is displayed on a 12-hour cycle.
Setting
Switches the noise reduction level for the luminance signals when a tape is played.
OFF : No noise reduction
LOW: Low noise reduction
HIGH: High noise reduction
Notes
• When you use noise reduction, there may be an afterimage depending on the condition of
the picture.
• The setting of this item does not affect a signal output via the DV jack.
Switches the noise reduction level for the chrominance signals when a tape is played.
OFF : No noise reduction
LOW: Low noise reduction
HIGH: High noise reduction
Notes
• When you use noise reduction, there may be an afterimage depending on the condition of
the picture.
• The setting of this item does not affect a signal output via the DV jack.
Setting
Reverses the subcarrier phase in the externally-synchronized playback mode.
0 DEG : The subcarrier phase is not reversed.
180 DEG: The subcarrier phase is reversed.
Note
You can adjust this item only in the externally-synchronized playback mode.
Finely adjusts the subcarrier phase in the externally-synchronized playback mode.
Press the J/j buttons to move the bar and press the EXEC button to select. (The triangle
under the bar is displayed in green when the setting is set to the factory preset value.)
Note
You can adjust this item only in the externally-synchronized playback mode.
Setting
Selects the audio mode.
FS32K : Switches the audio mode to the four channel mode (12-bit mode).
FS48K: Switches the audio mode to the two channel stereo mode (16-bit mode). (This
setting records the sound in all audio ranges, providing a high-quality sound recording.)
Notes
• When signals are input via the DV jack, the audio mode of the signals to be recorded is
the same as that of the input signals. The setting of this item is ignored.
• You cannot change the setting of this item during recording.
• Noise may occur at the instant you switch the audio mode.
Selects the input channel for audio dubbing.
CH1,2: Selects channels 1 and 2.
CH3,4 : Selects channels 3 and 4.
OFF: Disables audio dubbing.
Note
You cannot change the setting of this item while dubbing the sound.
Turns sound output on/off when the tape is played at a speed other than normal.
OFF : Does not output the sound when playing a tape at a speed other than normal.
ON: Outputs the sound when playing a tape at a speed other than normal.
Note
Even if you have set this item to ON, the sound may not be output or interrupted depending
on the tape format (DVCAM/DV) or tape conditions.